Cell Phone Docking Station - PowerPoint PPT Presentation

1 / 27
About This Presentation
Title:

Cell Phone Docking Station

Description:

Design a system to interface a home telephone network with a cell phone. ... Test audio I/O between cell and land phone, and also multiple land phones ... – PowerPoint PPT presentation

Number of Views:147
Avg rating:3.0/5.0
Slides: 28
Provided by: danf76
Category:

less

Transcript and Presenter's Notes

Title: Cell Phone Docking Station


1
Cell Phone Docking Station
ECE 345 Project Presentation
  • Daniel Finch
  • Mihir Shah
  • David Johns
  • TA Jeff Cook

2
Introduction
  • What
  • Who
  • Where
  • When
  • Why?

3
What
  • Design a system to interface a home telephone
    network with a cell phone.
  • Allow incoming calls to a cell phone to ring a
    home network
  • Allow audio communications between a cell phone
    and home network
  • Provide a seamless environment between the cell
    phone, the home network, and the subscriber line

4
Who, Where, When, Why
  • A person wishing to answer cell calls while at
    home without the discomfort of a small cell phone
  • A person wishing to charge a cell phone while
    keeping the cells connectivity readily
    available.
  • After work, plug the cell phone in the unit,
    charge it up and keep connected.

5
Objective - the original plan
  • What we intended to do
  • Provide 100 cell phone functionality through use
    of the landline phone

6
BUT
  • Motorola has no university support!

7
What we built
SLIC
8
DC / DC Converter
  • Uses MC34063A IC
  • Inverts 5V to -24V
  • Provides reference voltage for SLIC and ringing
    off hook detector

9
SLIC (MC33121) Functionality
  • Subscriber Line Integrated Circuit
  • Provides Tip/Ring telephone line conversion to
    audio I/O.
  • Audio dB level controlled by network attached to
    chip
  • Provides hook status of subscriber line

10
Audio Isolation
  • 11 Isolation transformers used to reduce
    feedback on audio I/O


SLIC
RXI
TIP
Audio Out
-
-
Audio In
TXO
RING

11
Ring Generator Circuit
  • 90V, 20Hz AC signal generated by Cambridge Black
    Magic ring generator (12VDC input).
  • Controlled by logic signals from the STAMP and
    component network

12
Ringing Hook Detector
  • Custom circuit.
  • Provides signal for the STAMP to switch the relay
    from the ringing circuit to the SLIC audio
    conversion circuit.

Rectifier And Reference
Inverter
-24V
12V
-
741
1k?
1k?
20Hz
1.3M?
620?

-
12V
741
-12V
Ring

270k?
20Hz Square Wave (when switched) 0V Else
Unity Gain Follower
-12V
1k?
13
Ringing Generator Output
  • Black Magic Telephone Ringing Generator (LS0014)
  • 20 Hz AC Sine Wave
  • 90 Vrms

14
Ring Output Rectifier
  • Diode -Resistor Network
  • Remove positive component of sine wave

15
After Unity Gain Follower
  • Provides current to drive the ring signal
  • Makes sinusoid more of a square wave

16
After Inversion
  • Provides positive ring signal for Basic Stamp 2
    to decode
  • 20 Hz square wave

17
Cellular Phone Ring Detection Attempts
  • Audio out from data connector
  • Too small (153mV)
  • Too Fast (900MHz)
  • Data Bus signals
  • Not readable by Basic Stamp 2
  • Current Sensing IC
  • Didnt work for Vin gt 5V

18
Final Cellular Phone Ring Detection Design
  • Audio out from 2.5mm audio jack on phone (20 Hz,
    1V-pp signal)

19
Amplified Cellphone Ring Signal
  • Amplified output, compared in Basic Stamp to
    amplitude level
  • High amplitude signal (- line noise) ring.

20
Stamp functionality
  • Cell ring detection

waitforring2 for reps 1 to 5 pause 20 if in20
then dialtone if in10 then noring totaltotal1 n
oring next if totalgt1 then ring goto waitforring
21
Stamp functionality
  • Ringing off-hook detection

pulsin 3, 1, stuff2 ' wait for pickup if
stuff2gt10000 then goback if stuff2lt30 then
goback goto pickup
22
STAMP flow chart
23
The Mechanical Finger
  • STA Push Tubular Solenoid
  • 5.2V input
  • Draws 3A
  • 12V / 5A Radio Shack Relay - Basic Stamp 2
    controlled
  • Mounted in custom built cradle for cell phone to
    line up with the solenoid.

24
Functionality and Testing
  • Test cell ring detection - no erroneous rings
  • Test 2 second on, 4 second off ringing - 5 ring
    maximum
  • Test hook status functionality
  • Test solenoid functionality of send button
  • Test audio I/O between cell and land phone, and
    also multiple land phones
  • Test cell hang up when phone goes on-hook

25
Challenges
  • Contacting Motorola - for both iDen and Microtac
    cell phones
  • Cell phone ring detection
  • Ringing off-hook detection
  • Implementing solenoid
  • Debugging noise from SLIC circuit

26
Recommendations
  • Dialtone generator
  • Databus decoding - Motorola or other brand
  • Ability to dial land-line phone using cell line
    connection
  • Better cell ring detection (using databus)

27
?Any Questions??Any Comments?
  • Where can I buy one?
Write a Comment
User Comments (0)
About PowerShow.com