Fundamentals%20of%20Liquid%20Cooling

1
Fundamentals of Liquid Cooling

• Thermal Management of Electronics
• San José State University
• Mechanical Engineering Department

2
Air as a Coolant

• PROS
• Simplicity
• Low Cost
• Easy to Maintain
• Reliable

• CONS
• Inefficient at heat removal
• (low k and Pr)
• Low thermal capacitance (low ? and Cp)
• Large thermal resistance

3
Using Alternate Coolants

• As electronic components get smaller and heat
  transfer requirements increase air becomes a less
  efficient coolant
• Liquid cooling provides a means in which thermal
  resistance can be reduced dramatically

4
Types of Liquid Cooling

• Indirect
• The coolant does not come into contact with
  the electronics.
• Direct (Immersion)
• The coolant is in direct contact with the
  electronics.

5
Fluid Selection

• Is the fluid in direct contact with the
  electronics?
• No. Water will normally be used due to the fact
  that it is cheap and has superior thermal
  properties.
• Yes. A dielectric must be used. Consideration
  must be given to the thermal properties of
  different dielectric fluids.

6
Microchannels

• Microchannels are most commonly used for indirect
  liquid cooling of ICs and may be
• Machined into the chip itself.
• Machined into a substrate or a heat sink and then
  attached to a chip or array of chips.

7
Microchannels

• Example Thermal Conduction Module used on IBM
  3080X/3090 series
• Heat is transmitted through an intermediate
  structure to a cold plate through which a coolant
  is pumped

Incropera, pg. 3
8
Microchannels
Incropera, pg. 155

• Rth,h Conduction Resistance through the chip
• Rth,c Contact Resistance at the Chip/Substrate
  Interface

• Rth,sub 3-D Conduction Resistance in the
  substrate (spreading resistance)
• Rth,cnv Convection Resistance from the
  substrate to the coolant

Note that this network ends with the mean fluid
temperature. If we use the inlet fluid
temperature, we also need to include Rcaloric
9
Motivating Example

• Laminar flow through a rectangular channel

Kandlikar and Grande, pg. 7
Kandlikar and Grande, pg. 8
10
Pressure Drop in Microchannels

• The pressure drop due to forcing a fluid through
  a small channel may produce design limitations.

• Limitations may include
• Pumping Power
• Mechanical Stress Limitation of the Chip Material

11
Pressure Drop Example

• If chip power increases mass flow rate must
  increase
• If mass flow rate increases pressure drop
  increases

Kandlikar and Grande, pg. 9
12
Optimization of Microchannels
Kandlikar and Grande, pg. 9

• How should the channels in the silicon substrate
  be designed for optimal heat transfer? Should the
  channel be deep or shallow? Make sure to give a
  valid reason.

13
Optimization of Microchannels
Kandlikar and Grande, pg. 9

• The channels should be deep so that the hydraulic
  diameter is small but the channel surface area is
  large.
• Caution Making the channels too small may result
  in unreasonable pressure drop.

14
Microchannel Issues

• Liquids Electronics
• Self-explanatory
• Fouling Leading to Clogging
• Clogging prevents flow of liquids through a
  channel
• Local areas where heat is not pulled away from
  components at a high enough rate are developed

15
Microchannel Issues

• Mini-Pumps
• Able to move liquid through the channel at a
  required rate
• Able to produce large pressure heads to overcome
  the large pressure drop associated with the small
  channels
• Tradition rotary pumps can not be used due to
  their large size and power consumption
• For information on some current solutions refer
  to
• http//www.electronics-cooling.com/html/2006_may_
  a3.html

16
Current Research for Single Phase Convection in
Microchannels

• Surface Area
• Adding protrusions to the channels to increase
  surface area.
• Adding and arranging fins in a manner that is
  similar to a compact heat exchanger.

Microstructures

• Examples of different geometries
• Staggered Fins
• Posts
• T-Shaped Fins

Silicon Substrate
Kandlikar and Grande, pg. 10
17
Current Research for Single Phase Convection in
Microchannels

• Manufacturing Technology
• Reducing cost of manufacturing
• Producing enhanced geometries
• For further information refer to article by
  Kandlikar and Grange

18
Current Research for Single Phase Convection in
Microchannels

• Justifying deviation from classical theory for
  friction and heat transfer coefficients when
  microchannel diameters become small
• Lack of a good analytical model
• Surface Roughness
• Accurate measurements of system parameters
• Ect.
• If you are interested in this take a look at
• Palm, B. Heat Transfer in Microchannels.
  Microscale Thermophysical Engineering 5155-175,
  2001. Taylor Francis, 2001.

19
Jet Impingement

• Benefits of using a jet in thermal management of
  a surface
• A thin hydrodynamic boundary layer is formed
• A thin thermal boundary layer is formed

Incropera, pg. 56
20
Classifying Impinging Jets

• Jets can be
• Free-Surface discharged into an ambient gas
• Submerged discharged into a liquid of the same
  type

• Cross Sections
• Circular
• Rectangular
• Confinement
• Confined Flow is confined to a region after
  impingement
• Unconfined Flow is unconfined after impingement

21
Classify the Following Jets

• Liquid jet released into ambient gas
• Liquid release into liquid of the same type

Incropera, pg. 56
Incropera, pg. 65
22
Classify the Following Jets

• Unconfined, circular, free-surface jet
• Unconfined, circular, submerged jet

Incropera, pg. 56
Incropera, pg. 65
23
Nozzle Design

• Nozzles are designed to create different jet
  characteristics
• Example Sufficiently long nozzles will produce
  both fully developed laminar or turbulent jets
  (Shown in b)

Incropera, pg. 58
24
Flow Regions

• Stagnation Region Jet flow is decelerated
  normal to the impingement surface and accelerated
  parallel to it. Hydrodynamic and thermal boundary
  layers are uniform.
• Wall Jet Region Boundary layers begin to grow

Incropera, pg. 62
25
Degradation of Heat Transfer During Jet
Impingement

• Splattering Droplets are eject from the wall
  jet region due to the distance the nozzle is from
  the heat source and the surface tension of the
  jet fluid
• Hydraulic Jump An abrupt increase in film
  thickness and reduction in film velocity
  occurring in the wall jet region

26
Confining Fluid Flow

• Adding a confining wall
• Adds low and high pressure regions
• Sometimes adds secondary stagnation regions
• Degrades convection heat transfer
• Decreases space needed to use jet impingement

Incropera, pg. 69
27
Two-Phase Boiling in Microchannels

• Fluid entering microchannels is heated to the
  point where it boils
• Flow in microchannels is highly unpredictable and
  can produce large voids and multiple flow regimes
  inside of tubes
• No accurate analytical models currently exist
  many analytical models have errors ranging from
  10 to well over 100

28
Flow Regimes in Two-Phase Applications
Garimella, pg. 107
29
Immersion (Direct) Cooling

• In direct cooling electronics are immersed into a
  dielectric liquid
• Closed loop systems are normally used due to both
  the cost of the liquids used and the
  environmental issues associated with the liquids
  escaping into the atmosphere

30
Typical Liquids Used in Immersion
Cengel, pg. 920
31
Boiling Used in Immersion
Cengel, pg. 918

• Electronics expel heat into the liquid
• Vapor bubbles are formed in the liquid
• The vapor is collected at the top of the
  enclosure where it comes in contact with some
  sort of heat exchanger
• The vapor condenses and returns to the liquid
  portion of the reservoir

32
Boiling Used in Immersion
Cengel, pg. 919

• Electronics dissipate heat through the liquid
• Vapor bubbles are generated
• As vapor bubbles rise they come in contact with
  the cooler liquid produced by an immersed heat
  exchange and they implode
• The prior example is more efficient due to the
  heat transfer coefficient associated with
  condensation

33
Cray-2 Supercomputer

• Cold fluid enters between the circuit modules
• Convection occurs, pulling heat from the
  electronics to the liquid
• The heated fluid is pumped to a heat exchanger
• Heat is transfer from the immersion liquid to
  chilled water in the heat exchanger

Incropera, pg. 6
34
Concerns with Immersion

• Introduction of incompressible gasses into a
  vapor space
• This will limit the amount of condensation that
  is allowed to occur and degrade heat transfer
• Leakage
• Environmental Concerns
• Reliability

35
Sources

• Cengel, Yunus A. Heat Transfer A Practical
  Approach. 1st edition. New York, NY McGraw Hill.
  1998
• Incropera, Frank P. Liquid Cooling of Electronic
  Devices by Single Phase Convection. Danvers, MA
  John Wiley Son. 1999
• Kandlikar, Satish G. and Grande, William J.
  Evaluation of Single Phase Flow in Microchannels
  for High Heat Flux Chip Cooling Thermohydrolic
  Performance Enhancement and Fabrication
  Technology. Heat Transfer Engineering. Taylor
  Francis Inc. 25(8). 2004
• Palm, Bjorn. Heat Transfer in Microchannels.
  Microscale Thermophysical Engineering 5155-175,
  2001. Taylor Francis, 2001.
• Kandlikar, Satish G. and Grande, William J.
  Condensation Flow Mechanisms in Microchannels
  Basis for Pressure Drop and Heat Transfer
  Models. Heat Transfer Engineering. Taylor
  Francis Inc. 25(3). 2004