Title: Why Study Soil-Plant-Water Relations?
1Why Study Soil-Plant-Water Relations?
An-Najah National University Faculty of
graduated studies Department of environmental
sciences
- Soil, Water Plant Relationship 400555
- Date 8-6-2011
- Dr. Heba Al-Fares
2Introduction
- A . Population
- Of the four soil physical factors that affect
plant growth (mechanical impedance, water,
aeration, and temperature) (Shaw, 1952 Kirkham,
1973), water is the most important. - Drought causes 40.8 of crop losses in the United
States, and - excess water causes 16.4
- insects and diseases amount to 7.2 of the losses
(Boyer, 1982).
3- Water is lost from both the soil surface
(evaporation) and the plant surface
(transpiration), and is seldom optimal for
maximum crop production in dry land
(non-irrigated) agriculture.
4- People depend upon plants for food.
- Because water is the major environmental factor
limiting plant growth, - we need to study soil-plant-water relations to
provide food for a growing population.
5What is our challenge?
The human population growth curve
6B. The Two-Square-Yard Rule
- The population is limited by the productivity of
the land. - There is a space limitation which is a space of
two square yards per person. - The suns energy that falls on two square yards
is the minimum required to provide enough energy
for a human beings daily ration.
7Movement of water through the soil-plant-atmospher
e continuum
- The movement of water through the SPAC is divided
into three parts - 1) water movement in the soil and to the plant
root - 2) Water movement through the plant, from the
root to the stem to the leaf and - 3) water movement from the plant into the
atmosphere
8What do plant growth curves look like?
- A. The Importance of Measuring Plant Growth and
Exponential Growth - Equations describing plant-growth curves
demonstrate how we can quantify, and thus
predict, plant growth. - Because water is the most important soil physical
factor affecting plant growth, it is important to
quantify plant growth to determine effects of
water stress. - We first consider the growth of the bacterium
E.coli.
9- If the start of our observations, at the time 0
min, there is 1 cell. When 20 min have elapsed
there are 2 cells. When 40 min have elapsed there
are 2 2 22 cells. - if N denotes the number of cells present at the
moment when t minutes have elapsed, then the
relation we seek is given by the equation - N 2t/20.
- Linnaeus showed that an annual plant would have
a million offspring in twenty years, if only two
seeds grew up to maturity in a year. - X 220
- where X is the number of offspring from the plant
in twenty years.
10B. Sigmoid Growth Curve
- The S-shaped, or sigmoid, curve is typical of the
growth pattern of individual organs, or a whole
plant, and of populations of plants
11The Role of Water in Plant Life
- Water comprises more than 80 of the living and
growing cells of most plants. - All actively growing plants have continuous
liquid phase from soil to leaf. - Growing plants need large amounts of water
- Water lose through leaves transpiration- in
dry climates, weight of water lost may be 100s or
1000s of time dry weight of plants. -  Water loss through stomata. If these partially
close to shut down some transpiration, it
inhibits CO2 intake and slows photosynthesis. - Â Plant suction in the day might be so high that
little growth takes place. Crop may make large
portion of its growth at night.
12The Role of Water in Plant Life
- Â Number of units of water/unit of D.M. produced
is called transpiration ratio. - Inverse of this ratio called water use
efficiencyÂ
13The Role of Water in Plant Life
- Soil the unconsolidated cover of the earth,
made up of mineral and organic components, water
and air and capable of supporting plant growth.
Most important function GROW PLANTS - As a medium for plant growth, soil performs four
functions - Anchors roots
- Supplies water
- Provides air
- Furnishes minerals for plant nutrition
- The pore space between the solids is taken up by
water and air. - Air takes up part of the pore space not occupied
by water. As the water increases, the air
content decreases.
14The Role of Water in Plant Life
- Functions of Water in the Plant
- Plants differ from animals because they are
nutritionally self-sufficient, or autotrophic. - Water serves as a hydrogen donor and thereby as a
building block for carbohydrates, which are
synthesized by plants making use of sunlight. - Exchange of gases uptake of CO2 and release of
water vapour to the atmosphere (transpiration). - Plants live permanently in one place, so they
have to remove water from the soil water
reservoir in their immediate vicinity.
15- Water is an important constituent of all plants.
- Root, stem and leaf of herbaceous plants consist
of 7095 water. - In contrast, water comprises only 50 of ligneous
tissues, and finally dormant seeds contain only
515 water. - water has a unique physiological importance in
the life of plants for CO2 assimilation, for
biochemical transformations and for the
transmission of impulses and signals.
16- As a chemical agent it takes part in many
chemical reactions, for instance in assimilation
and respiration. It is a solvent for salts and
molecules, and mediates chemical reactions. - Water is the medium of transport for nutrient
elements and organic molecules from the soil to
the root and the means of transport of salts and
assimilates within the plant. - Stimulation and motion of organelles and cell
structures, cell division and elongation are
examples of processes controlled by hormones and
growth substances, and water is the carrier of
these messengers, enabling the regulatory system
of the plant.
17- Water confers shape and solidity to plant
tissues. - The hydrostatic pressure in cells is dependent on
their water content, and permits cell enlargement
against pressure from outside, which originates
either from the tension of the surrounding tissue
or from the surrounding soil. - The large heat capacity of water greatly dampens
the daily fluctuations in temperature that a
plant leaf might undergo, due to the
considerable amount of energy required to raise
the temperature of water. - The vapour that transpires from leaves causing
cooling due to evaporation
18Availability of Soil Water to Plants   Â
- Â Water moves into the plant whenever suction in
the water in the plant is greater than that in
the water in the soil. Most plants withdraw water
from soils until soil moisture reaches about 15
bars. - Fine textured soils hold more water than sands at
field capacity - Fine textured soils are less droughtyÂ
19Depending on soil texture, which is determined by
the particle-size distribution, soils will vary
in water content at field capacity and at the
permanent wilting point. Both characteristic
values enclose the plant-available water content.
Silt loam soil contains the maximum of available
water. The water at the permanent wilting point
is not available to plants. The fineness of
texture increases with the silt and clay content,
presented as approximate percentages.
20Water Requirements of Crop Plants
- Â The rate at which water if available would be
removed from the soil and plant surface is
potential evapotranspiration (PET). - The ratio of evapotranspiration (ET) to (PET)
gives figure called relative evapotranspiration
or crop coefficient (Kco). - Energy is required to evaporate water from soil
and to cause plants to transpire.   - Crops utilize only 1 to 2 of energy
received. Utilization of energy may become the
next limiting factor when moisture is adequate
and good cropping practices are followed. - Â Many crops have critical stages of growth when a
water deficient will cause unusually large
reduction in yield. Â
21Adaptation Strategies of Plants to Overcome Water
Shortage
- According to the presence and supply of water,
ecologists divide terrestrial plants into - hygrophytes,
- mesophytes and
- xerophytes.
22Hygrophytes
- Hygrophytes are plants that thrive in generally
humid habitats, where there is no shortage to the
water supply throughout the growing season. - In temperate zones, in addition to these plants
with a humid biotype, there are many shade-loving
herbaceous forest species that also belong in
this category.
23Xerophytes
- Xerophytes are adapted to water shortage, which
may occur regularly and may persist over long
periods of time. - Anatomical and physiological specialization has
taken place to meet the requirements of these
plants so that they can survive extended periods
of drought. - To this group belong succulent plants that
establish an internal water reservoir for use
during drought, thereby postponing desiccation. - Another group of xerophytic plants are able to
endure considerable water loss from their tissues
without losing their ability to survive.
24Mesophytes
- Mesophytes fit in between these two extremes.
- Many plants from temperate climates belong to
this group, but the cultivated plants from those
regions are also included. - The latter cannot endure an extreme form of arid
climate without being irrigated. - However, for short periods of water shortage they
are well prepared. - When water supply falls short, they can reduce
their transpiration rate dramatically and modify
other processes.
25- How do plants react to water shortage?
- , and
- what kind of strategies have they developed with
respect to drought resistance?
26Drought escape
- Those plants that are adapted to drought escape
will germinate from dormant seeds only when there
is abundant rainfall. - Afterwards they can manage with a limited supply
of water because they can terminate vegetative
growth and become reproductive after a very short
life cycle of just a few weeks, even ending with
mature seed. - Subsequent dry periods are escaped through seed
dormancy.
27Drought escape
- Among cultivated plants, the short-lived two
rowed barley is a drought escaper. - Groundnut and cowpea are classed in this group
along with the C4 plants from the different
species of millet. - All of these crops reach maturity, although
annual precipitation may not exceed 250300 mm
28drought avoidance.
- Plants at adapted todrought avoidance may avoid
or at least retard desiccation of their tissues
by increasing water uptake, reducing water loss,
or by enhancing the internal storage of water. - Like the first group these plants maintain a
water balance that is largely in equilibrium. - They belong to the hydrostable or homoiohydric
species.
29- Water savers
- Many of these plants are succulents and can save
a large volume of water within parenchymatous
tissue when the very short periods of rainfall
occur. - Quite a number of species in the family Cactaceae
belong to this group. - Cacti, as well as plants of the families
Crassulaceae and others are representatives of a
group that demonstrate CAM. - These CAM plants effect a unique physiological
adaptation to water shortage. - During the night, however, they will be opened
for CO2 assimilation and accumulation in the form
of organic acids, which during the daytime supply
CO2 again for producing carbohydrates by
photosynthesis
30- There are also water savers among C3 and C4
plants - In many cases the plants possess distinct
anatomical features such as stomates that are
deeply sunk into the epidermis, thick and
leathery or fleshy leaves, small leaves, leaves
with waxy coatings over the cuticle and leaves
with a felt-like cover of fine hairs. - Some of the water savers restrict water loss
during dry periods by rolling or folding their
leaves
31Water spenders
- These plants raised water through deep rooting
system during the night from deep layers to more
shallow ones, where the water was released from
the roots into the surrounding soil. - This hydraulic lift enables plants to make use
of a larger water supply during the day for
transpiration and for CO2 assimilation. - Water spenders include esparcet.
- This is a perennial deep-rooted forage legume,
adapted to calcareous soils and native to
Mediterranean regions
32Drought tolerance
- Plants relying on this strategy are able to
tolerate a certain level of tissue desiccation. - During phases of desiccation they limit their
vital functions quite considerably. - The plants are said to be hydrolabile
33Osmotic adjustment
- The capability of solute accumulation is termed
osmotic adjustment. - When desiccation develops slowly over time, many
plants are able to accumulate inorganic ions or
organic compounds, such as sugars, alcohols and
amino acids, in their tissues. - The solutes are concentrated in the cytoplasm and
vacuoles, but the water content of the cells is
maintained at a more or less stable level. - By osmotic adjustment plants guard against a loss
of turgidity. - This adjustment will allow the plant to survive
periods of drought more vigorously and for longer
periods of time, and can allow the extraction of
water from soil - Sorghum is considered as a crop species
characterized by a strongly developed drought
tolerance compared with other crops. - soybean are capable of osmotic adjustment, and
the same is true of other grain legumes and
sugarbeet
34Water and Net Primary Production
- There is a well defined relationship between
water use and the amount of dry matter produced. - the net primary production, i.e. gross primary
production minus respiration
35Water, temperature and radiation
- Factors influence plant growth and can regulate
net primary production through - Net assimilation rate (NAR, rate of growth per
unit of leaf area). - A small biomass will result in a small leaf area
index (LAI, total green area of one side of a
leaf as a ratio of one unit of soil surface
area). - A small LAI is the second cause of reduced
productivity. - The Crop Growth Rate (CGR) is the rate of growth
per unit of soil surface area. - CGR NAR LAI (1.1)
- Equation 1.1 establishes that the productivity of
a crop stand is dependent on the photosynthetic
net productivity of the single leaf and of the
size of the total leaf canopy
36Relationship between net primary production of
terrestrial forests and annual precipitation as a
rough index of the level of available water.
37Seed yield of groundnut as related to water use.
The water use includes the transpiration of the
crop and the evaporation from the soil. Lysimeter
studies in Georgia and Florida, cultivar is
Florunner (after Boote and Ketring, 1990).
38Influence of temperature on the rates of gross
photosynthesis, respiration and net
photosynthesis (A) as well as on growth rate (B).
The three cardinal points for temperature are
the minimum, optimum and maximum values (Tmin,
Topt and Tmax). (Schematic after Pisek et al.,
1973 for (A) and Fitter and Hay, 1981 for (B).)
39The Role of Water in Soil
- Soil Genesis and Soil Functions
- Water is of primary importance for soil genesis.
- Without the action of water, soils would not
develop. - Soils originate from parent rock.
- The first step towards soil formation is the
weathering of these rocks. - Water contributes to the processes of weathering
through physical and chemical actions.
40The Role of Water in Soil
- The development of soil can be thought of as
occurring in two phases - Soil Genesis the weathering of rock substrates
by - Mechanical forces
- Chemical reactions
41The Role of Water in Soil
- 2) Soil Formation Hans Jenny (1941)
characterized soil formation as a function of
five independent variables climate, organisms,
topography, parent material, time. - Organism include such elements as the soil
microbial community, litter inputs, vegetation
type. - Parent material largely determines chemical
characteristics of the derived soils. - ? The interaction of organisms parent material
with climate produce a soil with characteristic
features.
42Soil genesis
- Soil genesis is accompanied by the formation of
soil structure, which is essentially dependent on
soil water. - Water causes the clay minerals to swell and
shrink, and the soil matrix becomes subdivided by
planes of weakness or by visible fissures.
43Soil genesis
- Also, ice formed by frost can separate the soil
matrix into aggregates of characteristic size and
form. - Without water there would be no transport
processes in the soil. Water in the soil is
seldom in a state of equilibrium. - Usually it is in constant motion within the soil
profile. The reason is that the energy state of
water, its potential, is generally not the same
but varies between different locations within the
profile.
44Physical weathering
- Physical weathering splits rocks and minerals,
but their chemical composition is not basically
changed. - Water is the main agent and works through frost
action, but in arid regions differential thermal
expansion of minerals can also split rocks. - The fragments formed are transported by surface
water from higher elevations downhill into the
valleys. - Here the fine debris is deposited in alluvial
fans, burying the former bottom of the valley,
and leveling the topographical features.
45Chemical weathering
- Chemical weathering breaks down minerals by
hydration, hydrolysis and dissolution. - The disruptive force of water is greatly
augmented by protons or hydronium ions (H3O)
that are derived from organic and inorganic
acids. - In this way even the very insoluble silicates are
finally broken down. - Increasing the temperature accelerates the
kinetics of destruction.
46- Water moves cations, silicic acid, and iron and
aluminium compounds solutes as well as colloidal
solids deeper into the soil body or even beyond
the soil into deeper strata. - Disintegration, displacement, precipitation and
leaching are essential parts of the pedogenic
processes, supported by water.
47Soil water
- Soil water is the most limiting factor for crop
production in the world. - Only 45 of the earth's arable land receives
adequate moisture for crop growth - Soil water carries nutrients to a growing crop
and has a significant effect on aeration and
temperature of the soil.
48Soil WaterÂ
- One of the most important factors affecting crop
production. - Water must be available to replenish that lost by
evaporation and transpiration. - Soil water carries nutrients in solution to the
growing crop. - Has significant effect on aeration and
temperature conditions of the soil. - Seldom is the water content of soil at optimum
value for maximum crop production.
49How is Soil Water Classified?
- 1) Hygroscopic Water is held so strongly by the
soil particles (adhesion), that it is not
available to the plants. - 2) Capillary Water is held by cohesive forces
greater than gravity and is available to plants. - 3) Gravitational Water is that water which cannot
be held against gravity. - as water is pulled down through the soil,
nutrients are "leached" out of the soil (nitrogen)
50Soil water
- There are certain limits for soil water.
- Field capacity is when the soil pores are so full
of water that the next drop will leach downward
out of the rooting zone. - The opposite extreme is wilting point, the level
at which plant roots can no longer take in water
and turgor is lost (wilting). - The goal of a soil, water, plant continuum is to
maintain the soil water between these extremes,
allowing nutrient movement, aeration, and
supplying water in excess of evaporation and
transpiration (evapotranspiration). - Measuring plant available water and adjusting
water levels with irrigation is another way
mankind has tried to modify the environment to
maximize food and fiber production
51Depending on soil texture, which is determined by
the particle-size distribution, soils will vary
in water content at field capacity and at the
permanent wilting point. Both characteristic
values enclose the plant-available water content.
Silt loam soil contains the maximum of available
water. The water at the permanent wilting point
is not available to plants. The fineness of
texture increases with the silt and clay content,
presented as approximate percentages.
52Moisture holding capacity is an essential feature
of soils
- Soil can become saturated if all pores filled
- All water is hold by soil particulars, at field
capacity (FC) - Capillary water is usually present
- Extracted by plants
- Wilting point (WP)
- Plant no long extract water
- All affected by soil texture
- Sand
- Lower capacity
- Clays
- Higher capacity
53WATER CONTENT
- Water content is a measurement of the amount of
water in the soil either by weight or volume and
is defined as the water lost from the soil upon
drying to constant mass at 105C
54Water content at different soils
55- Energy Concept of Soil MoistureÂ
- Expression in terms of energy makes it more easy
to compare availability of the moisture in soils
of different textures.    - Most commonly accepted unit at present is bars of
suction. Suction is negative pressure, the higher
the numerical value the lower the energy status
of the water. - Soils at field capacity - 0.1-0.3 bars of
suction - When soils at wilting point - 15 bars of suction
56Water Holding Capacities of Soils
- The amount of water a soil can retain is
influenced by - soil texture
- soil structure
- organic matter.
57Water Holding Capacities of Soils
- Soil Texture
- The smaller the soil particles, the greater the
soils water holding capacity. Clay has more
water holding capacity than sand. - Small soil particles (clay) have more small pores
or capillary spaces, so they have a higher water
holding capacity. Large soil particles (sand)
have fewer capillary spaces, therefore less
ability to hold water.
58Water Holding Capacities of Soils
- Soil Structure
- Â is the way soil particles (sand, silt, clay)
arrange, and combine. Many soil structure classes
are differentiated on the basis of their
aggregate size, shape, arrangements - A soil structure has a direct correlation to the
amount of water it can retain. - Â
59Water Holding Capacities of Soils
- Organic Matter
- Organic matter aids in cementing particles of
clay, silt, and sand together into aggregates
which increases the water holding capacity. - Decomposition of organic matter also adds
vital nutrients to the soil.Â
60- Water Movement in Soils  Â
- Water will move in a soil from one point to
another if the water at the first point has
higher energy status than the water at the
second.    - Water entering a dry soil is held at higher
suction in the zone below the wetting front and
water moves down. The rapidity of movement
depends on the size of the energy difference and
soil characteristics. - If water is applied to the surface by rain or
irrigation much faster than it can enter soil and
be transmitted downward, the excess water
accumulates on the surface. If the slope is
great, erosion will likely result (unless surface
stable or protected by plant residues). - The kinetic energy of rain can break down
aggregates at the soil surface
61Drainage
- Â Â Â
- Detrimental effects of excess water areÂ
- Water moving laterally across the surfaceÂ
- Water loss and erosion
- A layer with limited water permeabilityÂ
- Can be treated with subsoiler
62Soil Fauna and Vegetation Cover
- The soil is a porous body built up from inorganic
and organic solid particles with pore spaces in
between. - The development of immature soils is accompanied
by - humification,
- weathering of minerals,
- release of nutrients,
- a vigorous development of plant cover,
- stronger rooting and
- soil colonization and an intensified nutrient
cycling. - Such soils become more porous.
63Soil Fauna and Vegetation Cover
- Soil animals of different sizes work through the
ground, - mixing inorganic and organic particles, creating
connecting pores, and - stabilizing aggregates within soil horizons and
near the surface. - In the course of this development the soils
quality as a habitat for plants improves.
64Soil Fauna and Vegetation Cover
- The development of the soil and of the plant
association go along with (and depend on) each
other. - The soil is effectively protected against erosion
by a dense vegetative cover, by roots and by a
litter layer. - Stabilized soil surfaces allow rain water to
enter the soil at high rates, a very important
characteristic during intense rain storms.
65- The favorable state of soil conditions under
vegetation cover will not last forever. - Climatic change, leaching of calcium carbonate,
progress in weathering, acidification, or human
impacts can contribute to soil degradation and
loss of its properties as a habitat
66Controlling and Measuring Soil Moisture Â
- Maximum crop production would be attained if soil
moisture suction could be held at a value low
enough that the energy exerted by the plant would
be minimal. - Instruments of many types marketed for measuring
soil moisture. - TensiometerÂ
- More useful in sands
- Â Removing a soil sample from appropriate
depth/drying/weighing will give you a reasonable
figure. - Some soils change color as they go from wet to
dry. You "feel" it.   Observe both crop and soil
closely for signs of moisture stress. Leaf
rolling in corn - Measure rainfall/estimate ET on open pan.
Computer using meteorological data to make
recommendation to farmer.