Title: Quantum Optics
1Quantum Optics
Page 127
- Behavior of light at the atomic level
- Best explains the interaction of light with
matter - Wave theory starts to break down at the atomic
level the classical example of this breakdown is
the photoelectric effect
2The Photoelectric Effect
Collector Plate (Anode)
VACUUM TUBE
Light shone at the metal cathode in a vacuum tube
causes electrons to be released toward the anode
? current flows in the circuit
Current flows
Ammeter
3Photoelectric Effect
- When light energy is shone on a metal plate,
electrons are released by the metal - Wave theory predicts that
- the cumulative energy of absorbed light will
eventually cause an electron to escape
(sunbathing effect) - Any wavelength of light will produce stimulated
emission of electrons provided sufficient total
energy is incident - The more intense the incident light energy, the
higher the energy contained in released electrons
4Photoelectric Effect
Quantum theory proves wave theory wrong, showing
that
(a) the cumulative energy of absorbed light will
eventually cause an electron to escape
electron release is instantaneous provided
incident photon energy exceeds electron-binding
energy
(b) any wavelength of light will produce
stimulated emission of electrons provided
sufficient total energy is incident
Only wavelengths of light that deliver energygt
binding energy will stimulate electron release
- (c) The more intense the incident light energy,
the higher the energy contained in released
electrons
Kinetic energy of released electrons is
independent of incident light intensity
5Atomic Energy Levels(not accounted for by Wave
Theory)
- At the atomic level, light exists as packets of
energy (photons) - Photons have discrete energy levels
- Electrons orbiting an atomic nucleus also have
discrete energy levels
6Quantum Optics Photon Energy
7Frequency (wavelength) vs. Photon Energy
- Compare the energy carried by a green photon
(587.6 nm) to that of a 400 nm blue photon
8Defining the electron Volt (eV)
- Avoid dealing with large negative exponents
(10-19 range) for photon energy (joules) ? define
a more convenient energy unit
- 1 electron volt energy obtained by a photon
when it is accelerated through a potential
difference of 1 volt (J/C)
9Photon Energy in eV
Blue light (400 nm) E 3.10 eV Green light
(587.6 nm) E 2.11 eV Red light (700 nm)
E 1.77 eV
10Atomic Energy Levels explain the Photoelectric
Effect
11Energy Levels Photon Absorption
Absorbing a photon of sufficient energy, an
electron jumps to a higher energy level
12Energy Levels Photon Emission
13Energy Levels Photon Emission
When an electron drops to a lower energy level, a
photon is emitted
14Atomic Energy Levels
Page 128
- Ground state (E0) lowest, most stable energy
level in an atom - strongest electrostatic attraction between
nucleus and electron - lowest electron kinetic energy
- Excited states (E1 E2 etc.) with elevation to
higher energy levels, electrons become less
stable - weaker electrostatic attraction
- higher electron kinetic energy
- farther (on average) from nucleus
15Atomic Energy LevelsHydrogen Atom
Page 129
16Energy Levels Hydrogen Atom
- Negative sign ? indicates electrostatic
attraction to nucleus (Binding Energy) - Consider negative electron energy as the
electrostatic hill that the electron must climb
to be freed from the atom - Zero energy ? free electron
17Atomic Energy Diagram
- Shows all the valid energy levels for the atom.
- Energy required for an electron to jump to a
higher level - Photon energy released as an electron drops to a
lower level
18Hydrogen Energy Diagram
19Ionization State
13.6 eV
0
E5
E4
E3
12.74 eV
-1
12.09 eV
E2
Fig 78, p 128
-2
486 nm
656 nm
-3
E1
10.2 eV
-4
-5
-6
-7
-8
Transition Level above Ground State (eV)
121 nm
Electron Energy (eV)
-9
-10
HYDROGEN ENERGY LEVEL DIAGRAM
-11
-12
-13
E0
0 eV
-14
20Hydrogen Balmer series encompasses transitions up
or down to/from the first excited state
(E1). Note the hydrogen F line (E3 ? E1) and C
line (E2 ? E1)
21Energy Levels Hydrogen Atom
- After absorbing energy, the electron remains in
an excited state for an extremely short period (
10 nsec) - Spontaneous emission as the unstable, excited
electron drops to a lower energy level, it emits
a photon. - Photon energy is equal to the difference in
atomic energy levels
22Energy Levels Hydrogen Atom
Photon energy for the transition from E2 to E1
Hydrogen C-line
23Energy Levels Hydrogen Atom
- A single energy jump from a higher excited state
causes a smaller energy transition (e.g. from E3
to E2)
24Energy Levels Hydrogen Atom
- Multi-level energy transitions can also occur
(e.g. from E3 to E1)
Hydrogen F-line
- The greater the energy transition as an electron
jumps to a lower energy level, the shorter the
wavelength of the emitted photon
25Atomic Spectra Hydrogen
- All energy transitions (single-level and
multi-level) are possible for the hydrogen atom. - Photons corresponding to all possible transitions
are emitted - gives rise to characteristic discrete spectral
lines of low pressure H2 gas
26Atomic Spectra Hydrogen
- Discrete hydrogen spectral lines ? fingerprint
for hydrogen. - Discrete hydrogen spectra used extensively in
astronomy - Characteristic atomic spectra in a gas best seen
at low pressure - at higher pressures, spectra
begin to change
27Atomic Spectra
Spectroscope
- Bunsen burned salts containing various elements
in a flame - placed a series of slits in front of the flame
- directed the light through a prism to disperse
?s - This allowed him to view the line spectra of
elements
28Absorption vs. Emission Spectra
                                               Â
       Â
29Absorption Spectra
30700 nm
600 nm
500 nm
400 nm
www.chem.uidaho.edu
31Solar Spectrum
www.chem.uidaho.edu
32Emission Spectra
33(No Transcript)
34Atomic Spectra
The colors of fireworks are created by atomic
line spectra
35Atomic Spectra Hydrogen
- Increasing gas temperature excites a greater
proportion of H atoms ? more atoms spontaneously
emitting photons - Explains why gas discharge lamps glow brighter as
they warm up
36Atomic Spectra
- Increasing gas pressure changes atomic spectra ?
collisions between molecules also cause energy
exchanges. - As pressure increases, collision frequency
increases ? discrete spectra gradually give way
to a continuous spectrum
37Continuous Spectrum
38QQ1. Which transition in the hydrogen atom would
result in emission of the shortest wavelength
photon?
- E0 ? E1
- E3 ? E1
- E4 ? E1
- E5 ? E2
wrong direction
3.4 0.85 2.55 eV
3.4 0.54 2.86 eV
?
1.51 0.38 1.13 eV
39QQ2. What type of atomic spectrum would most
likely be seen for a hydrogen gas cloud in space?
- Absorption spectrum
- Emission spectrum
- Continuous spectrum
- All of the above
? Low pressure, cold gas
40Fraunhofer Lines (Solar Absorption Spectrum
Page 129
41Major Fraunhofer Lines (Solar Spectrum)
Page 129
Designation Element Wavelength (nm) Designation Element Wavelength (nm)
y O2 898.765 c Fe 495.761
Z O2 822.696 F H ß 486.134
A O2 759.370 d Fe 466.814
B O2 686.719 e Fe 438.355
C H a 656.281 G' H ? 434.047
a O2 627.661 G Fe 430.790
D1 Na 589.594 G Ca 430.774
D2 Na 588.997 h H d 410.175
D3 He 587.565 H Ca 396.847
E2 Fe 527.039 K Ca 393.368
b1 Mg 518.362 L Fe 382.044
b2 Mg 517.270 N Fe 358.121
b3 Fe 516.891 P Ti 336.112
b4 Fe 516.751 T Fe 302.108
b4 Mg 516.733 t Ni 299.444
42Solar Spectrum
- Series of absorption lines produced when sunlight
emitted from the hotter solar chromosphere is
absorbed by the cooler outer solar photosphere - Hydrogen makes up 92.1 of the suns atoms,
helium 9.2, and sodium, calcium, and iron 0.1 - Overall, several thousand solar Fraunhofer lines
representing 67 elements
43Table 1 Major Solar Fraunhofer Lines Table 1 Major Solar Fraunhofer Lines Table 1 Major Solar Fraunhofer Lines
Designation Wavelength (nm) Origin
A 759.4 terrestrial oxygen
B 686.7 terrestrial oxygen
C 656.3 hydrogen (Ha)
D1 589.6 neutral sodium (Na I)
D2 589.0 neutral sodium (Na I)
E 527.0 neutral iron (Fe I)
F 486.1 hydrogen (Hß)
H 396.8 ionized calcium (Ca II)
K 393.4 ionized calcium (Ca II)
44Fluorescence
Page 129
45Fluorescence
Page 129
- Fluorescence is an example of energy absorption
followed by spontaneous photon emission. - Many substances that can be raised by a
stimulating source from ground state to an
excited state, then spontaneously emit photons,
will theoretically fluoresce.
46Fluorescence
- Typically a high frequency source (UV) is needed
to raise atoms from the ground state. - A fluorescent substance could undergo a single
energy level transition E0 ? E1 for excitation,
followed byE1 ? E0 for spontaneous emission.
This is rare. - Most fluorescent substances, after excitation,
will undergo a non-radiative transition (e.g.
E2 ? E1) followed by photon release (e.g. E1 ? E0)
47Fluorescence (typical case)
Fig 79, p 130
energy loss to surroundings
non-radiative transition
fluorescence emission
high frequency radiation (UV)
lower frequency radiation
48Fluorescence
- Most substances are not 100 efficient, emitting
less energy than they absorbed. - Thermal agitation (vibrational loss) is the most
common cause of the energy loss between
absorption and emission (non-radiative
transition) - The emitted photon will therefore have lower
energy than the exciting photon
49Fluorescence Stokes Reaction
Fluorescence emission (photon)
50Fluorescence
- Thermal losses explain why fluorescent emission
usually has longer wavelength (different color)
than the excitation source. - e.g. blue light may be absorbed by a fluorescent
substance. Thermal agitation causes energy loss
from the excited atoms, leaving less energy for
emission. The emitted photon will have longer ?
(e.g. green) - The difference in energy between the excited and
emitted photon is called Stokes shift
51Explaining Stokes Shift
- Molecules contain discrete electronic energy
levels (E0, E1, E2 , etc. ..). - Each energy level also consists of a series of
vibrational sub-levels (due to motion of the
non-rigid nucleus within the molecular
framework) - Interaction with surrounding molecules causes
rapid loss of vibrational energy to the
environment (this is the thermal agitation
loss non-radiative transition) - The various types of atomic energy (electronic,
vibrational, spin angular momentum etc.) are
depicted in Jablonski diagrams
52Jablonski Diagram for Fluorescence
- Incident radiation excites the ground state
molecule (A) - The molecule is also excited to vibrational
levels of the excited state - Vibrational levels rapidly deactivate due to
collisions with the surrounding environment until
the molecule reaches its lowest excited state
(vibrational relaxation) - If the interaction between the excited molecule
and its surroundings is not enough to cause the
large energy transfer to return it to ground
state, the molecule fluoresces (F, radiative
decay)
53Ophthalmic Applications of Fluorescence
Page 131
54Ophthalmic Applications of Fluorescence
- Sodium fluorescein has several applications in
ophthalmic practice - tear film instillation to
- visualize ocular surface anomalies
- evaluate tear film stability
- Fluorescein angiography
55Fluorescein
- A cobalt blue filter provides excitation energy
(365 - 470 nm) - Thermal agitation decreases the energy available
for emission - 522 nm green photons are emitted
56Fluorescein Ocular Surface Evaluation
- Includes detection of corneal surface abrasions,
superficial punctate keratitis, foreign body
tracks in contact lens wearers etc. - Fluorescein is placed into the tear film and the
green emission pattern is viewed through a
(stimulating) cobalt blue filter (usually with a
biomicroscope)
57Superficial punctate keratitis
58CorneaDouble Abrasion
Fluorescein
59Fluorescein Angiography
Page 132
- Fluorescein dye is injected into the blood (or
may be taken orally) - A retinal camera equipped with UV filter is used
to monitor the passage of fluorescein through the
pre-retinal vasculature - Any fresh hemorrhages, vascular leak etc. shows
up as fluorescent green patches outside the blood
vessels (which also fluoresce)
60Fluorescein Angiography Eye
Arterial Phase NORMAL
61Fluorescein Angiography Eye
Early venous phase - Normal
62Fluorescein Angiography Eye
Complete Filling Arteries Veins NORMAL
63Fluorescein Angiography Eye
Late Phase - Fading of Dye NORMAL
64Fluorescein Angiography Eye
Early Phase - Dye leakage DIABETIC RETINOPATHY
65Fluorescein Angiography
- Fluorescein angiography is especially useful in
diabetes where microaneursyms, and dot and
blot hemorrhages show up.
66Fluorescein Angiography Eye
Arterio-venous Phase - Neovascularization
DIABETIC RETINOPATHY
67Fluorescein Angiography Eye
Late Phase - Hemorrhage from new vessels
DIABETIC RETINOPATHY
68Fluorescein Angiography Dot Hemorrhages
Microaneurysms
69Fluorescein Angiography Dot Hemorrhages
Microaneurysms
70Fluorescence Microscopy
- Fluorescence overlay antigen mapping (C) of a
skin section using two Mabs. - A RITC-conjugate
- B FITC-conjugate
- C overlay image of A and B shows yellow
fluorescence on sites where both antigens are
present (between arrows). (Bar, 50 microns) - From Jonkman J Clin Invest, Volume 95(3).March
, 1995.1345-1352
71Phosphorescence
Page 132
72Phosphorescence
Page 132
- Same principle as fluorescence, but atoms of a
phosphorescent substance will remain in the
excited state for a much longer period of time. - This requires the existence of a metastable state
- i.e. a relatively stable excited state that the
atom may remain in from second to hours. - To understand the basis of a metastable state
(also applies to lasers) must look at sources of
atomic energy beyond electronic energy
73Practice Problem I
Most fluorescent substances emit a photon of
different wavelength than the absorbed photon.
The reason for this is
- spontaneous emission occurs in a random direction
with a random wavelength - vibrational losses in the excited substance
reduce the energy available for emission - thermal transfer increases the energy of the atom
resulting in an emitted photon of shorter
wavelength - metastable substances build up stored energy
resulting in emission of a higher energy photon
?
74Practice Problem II
Fluorescence could be described as a process of
- stimulated emission, where high energy photons
cause an atom to drop immediately to the ground
state, emitting photons of longer wavelength due
to thermal loss - thermal agitation of an atom from a metastable
state to a higher, unstable state, causing an
immediate drop to ground state, accompanied by
photon emission - spontaneous emission, where longer wavelength
photons are absorbed and shorter wavelength
photons are emitted due to thermal loss - spontaneous emission, where higher energy photons
are absorbed, and lower energy photons are emitted
?
75Practice Problem III
In the process of fluorescence, Stokes shift
refers to
- the almost immediate drop by an excited atom to a
slightly lower energy level prior to spontaneous
emission of a fluorescent photon of shorter
wavelength than the exciting photon - the increase in atomic energy level that occurs
when the atom absorbs a photon of sufficient
energy to raise it to the required state to allow
subsequent fluorescent emission - the difference in energy level between excitation
and emission energy that is responsible for the
characteristic wavelength of the emitted photon - the tendency of atoms to vibrate and make
translational movements as they are raised to
higher energy levels by exciting photons
?
76Practice Problem IV
Compared with fluorescence, phosphorescence
differs
- in that phosphorescent atoms must be raised to
substantially higher energy levels due to the
much more significant thermal losses that occur
for the prolonged life of the excited state - in that phosphorescence involves a combination of
spontaneous and stimulated emission, while
fluorescence involves only spontaneous emission - only in the presence of a metastable state to
maintain excited phosphorescent atoms above
ground state for prolonged time periods - only in the fact that phosphorescent atoms do not
suffer any vibrational (thermal) loss after
initial excitation, so the stimulating energy is
equal to the transitional energy giving rise to
the emitted photon
?