Hitachi Z31A Camera Setup and Operation - PowerPoint PPT Presentation

1 / 35
About This Presentation
Title:

Hitachi Z31A Camera Setup and Operation

Description:

Use lever on front of tripod plate to attach camera to tripod, always keeping ... zoom rocker to change the optics of the lens from W (wide-angle) to T (telephoto) ... – PowerPoint PPT presentation

Number of Views:242
Avg rating:3.0/5.0
Slides: 36
Provided by: david1035
Category:

less

Transcript and Presenter's Notes

Title: Hitachi Z31A Camera Setup and Operation


1
Hitachi Z-31A CameraSet-up and Operation
2
Tripod Parts 1
Plate

Head
Panhandle

Legs or Sticks

Dolly
3
Tripod Parts 2
Plate

Mounting Plate
Head
Panhandle
4
Tripod Set-Up 1
  • Use lever on front of tripod plate to attach
    camera to tripod, always keeping one hand on
    camera handle to keep it from falling

Attach camera to tripod plate with this lever
(pushing red button will allow camera to be taken
back off plate)
5
Tripod Set-Up 2
Your handle hand never leaves the camera until
you are sure the camera is securely mounted on
the tripod.
  • To verify that camera is securely attached to
    tripod plate, pull straight up on camera with
    your handle hand
  • If camera will not come off of tripod plate when
    pulling up on it firmly, it is safe to let go of
    camera

6
Tripod Set-Up 3
If your tripod has a claw ball, it may be used to
quickly level the camera as follows Loosen claw
ball with one hand, while the other hand firmly
holds camera by its top handle
Claw ball
Claw ball knob
  • Rotate camera on claw ball until it is level
  • Once level, retighten camera on tripod using claw
    ball knob

7
Tripod Operation 1
  • Before walking away from camera on the tripod,
    always tighten tilt lock
  • The pan lock
  • lever is located
  • on the back
  • of the tripod
  • head

Make sure to release tilt and pan locks before
attempting to move camera in either direction, or
you risk damaging tripod head!
8
Tripod Operation 2
  • Tighten pedestal lock to secure camera at one
    height
  • Use pedestal crank to raise or lower whole camera

9
Tripod Operation 3
Panhandle always points opposite lens
  • Use panhandle, and not camera itself, to control
    camera movement
  • Use tilt tension knob to set desired level of
    tilt resistance

Tilt tension knob is located left side of tripod
head
10
Tripod Operation 4
Expander locks
  • The tripod may be extended and/or leveled by
    using knobs on lower legs (expander locks may
    have to be loosened at same time)
  • On the Bogen Auto-dolly, a single pedal is used
    to unlock all three wheels on the dolly (down
    position) causing the dolly to roll, or to raise
    the wheels (up position) and drop the dolly into
    a stationary position on the floor

Tip up with toe to lock
Push down on pedal to unlock
Dolly lock- unlock pedal
11
Power-Up 1
  • Before power-up, make sure that the camera power
    switch, located to the left of the GAIN switch,
    is set to the OFF/down position
  • This prevents the camera from receiving a harmful
    power surge as the power is brought on line
  • The last step of power-up is to turn on the camera

This panel is located on lower left of the
cameras left side
12
Power-Up 2
  • Buckle battery belt around legs of tripod with
    the switch and jack facing up

Power jack
Power switch
13
Power-Up 3
  • Using the 5 to 3-pin power cable, plug the
    battery belt into the jack on the back of the
    camera
  • Align both the pin and barrel parts of the 3-pin
    connector before pushing it onto the jack. Then
    spin the barrel clockwise to lock the connector
    onto the jack.
  • Make sure belt is on charge and camera is on
    standby

Power jack located on back side of camera
14
Power-Up 4
  • Switch the charge-operate lever on the battery
    belt to operate, making sure that the camera is
    still in OFF mode
  • Last, switch the camera power switch from the
    OFF/down to the ON/up position
  • The Power indicator light should glow green

15
Power-Up 5
  • Verify that camera has power by pressing zoom
    rocker (if camera has power, lens will move)

Zoom rocker located on right side of camera next
to lens
Zoom rocker
16
Power-Up 6
power select switch
  • If camera still does not power-up with a good
    battery belt, flip the camera power switch on
    back to the Power/left position. This switch
    may have accidentally been switched to the
    VTR/right position, which requires the
    multi-pin cable.

This panel located on back of camera
17
Lens Filters
Dial lens filter to appropriate setting
This panel located on the cameras left side
next to the lens
  • Use 1 (3200 oK) for indoor, tungsten lighting
  • Use 2 (5600 oK 1/8ND) for outdoor lighting with
    neutral density filtering to cut glare, but light
    level also will be cut
  • Use 3 (5600 oK) for outdoor lighting
  • Lens dial 4 is the internal lens cap, and should
    be used when the camera is put away

Lens dial
18
Color Balance Preset
Color balance switch
Once the lens filter has been set for existing
lighting conditions, setting the color balance
switch to the preset/up position will give the
cameras best guess of color balance.
This panel located behind sliding door on
cameras left side
19
Switch Settings forManual Color Balance
The first step to manual white balance is to set
the switches properly, without which the camera
will not accept a manual white balance
  • Set Monitor Select G R Switches to middle the
    position
  • Set Gain Switch to Auto/down position
  • Gain in the Preset/up position will give the
    cameras best guess as to white balance

This panel located behind sliding door on
cameras left side
20
Color Balance Manual
  • Next zoom into something white so that it fills
    the lens, and throw the camera out of focus
  • Then, hold the AUTO WHT/BLK switch up for 3
    seconds.
  • Last, black balance by holding the AUTO WHT/BLK
    switch down and then releasing it.

These switches located at bottom left of cameras
left side
21
Proper Use of White Card
NOTE It is very important when manual white
balancing using a white card, that the card be
held by the talent under the exact lighting
conditions to be used during the shoot. So, only
white balance AFTER all portable lights have been
set-up and turned on, and have the talent hold
the white card near, or in front of, their face
(the most important part of the scene). Common
mistakes are to white balance before the lights
have been set-up, or to hold the white card in
front of the camera lens, rather than in front of
the talents face.
22
Color Bars
  • Flipping the BAR/CAM switch to BAR will cause
    SMPTE color bars to be output from the video
    out jack on the cameras back panel. Color bars
    also will appear in the viewfinder (in black and
    white)
  • Flipping the switch to CAM will return the
    camera to normal operation.

These switches located at bottom left of cameras
left side
23
Gain Up
  • In low-light situations, to electronically boost
    the video signal, put the GAIN switch into 18dB
    for max. boost, and 9dB for partial boost.
  • The Gain switch also boosts video noise, and
    lowers the quality of the video signal, so make
    sure that the aperture is fully open before
    resorting to gain.

These switches located in lower left of cameras
left side
24
Zoom Control 1
  • Use the zoom rocker to change the optics of the
    lens from W (wide-angle) to T (telephoto)
  • Pushing the W side of the rocker will widen the
    lens angle, taking in more of the scene but
    making the subject appear smaller
  • Pushing the T side of the rocker will narrow the
    lens angle, taking in less of the scene but
    making the subject appear larger

The zoom rocker is located on the right side of
the camera next to the lens
25
Zoom Control 2
  • To put the lens into manual zoom, turn the Zoom
    MANU-SERVO knob MANU (manual)
  • The zoom then can be manually controlled using
    the zoom ring on the lens

The Zoom MANU-SERVO knob is located on the
underside of the lens
The manual zoom ring is located directly behind
the focus ring on the lens, and has a silver
lever on it for easy access
26
Focus Control 1
  • Use the focus control ring to bring the picture
    into or out of focus.
  • As with most 3-chip professional cameras, there
    is no automatic focus on the Z-One.

The focus control ring is the largest grippable
ring on the front of the lens
27
Focus Control 2
Remember that the steps for focusing on a subject
are as follows
1
  • Zoom in ALL-THE-WAY
  • to the main subject

2
  • Pick a detail on the subject
  • (such as the eyes or hair),
  • and use the focus ring
  • to bring it into focus
  • Zoom back out to desired
  • shot

3
28
Exposure Control 1
  • For manual exposure control, slide the Iris A-M
    switch to M
  • When in M, pushing the iris button will
    temporarily invoke automatic exposure. Use it
    when you are unsure of the proper exposure and
    want to see the cameras best guess.

These switches located on cameras right side
next to lens
29
Exposure Control 2
  • Once M has been selected with A-M switch, the
    exposure ring may be used for manual exposure
    control.
  • F1.6 lets in the most light, F16 lets in the
    least.
  • C closes the aperture entirely

manual zoom
exposure ring
macro focus
30
Macro Focus
  • Activate Macro Focus by pulling up on the macro
    release knob and rotating macro focus ring
    counter-clockwise.
  • Once lens is in macro focus, the zoom rocker is
    used for fine focus (not the focus ring)
  • Lens MUST be taken back out of macro focus to
    resume normal operation (macro knob will click
    back in place)

Macro focus ring
Macro release knob
Back plane focus
31
Back Plane Focus
  • If the lens will not focus normally even after
    taking it out of macro focus, the back plane
    focus probably is out of adjustment (which may
    have happened by mistake when macro focusing)
  • Unlike the macro focus knob which pulls out, the
    back plane focus knob unscrews
  • The back plane focus controls the way the lens
    maintains focus through its zoom range

Macro focus ring
Macro release knob
Back plane focus
32
Back Plane Focus 2
There are 4 steps for resetting the back plane
focus
  • Zoom in all the way to a subject and focus on a
    detail
  • Zoom out all the way and loosen the back plane
    focus knob by unscrewing it
  • Focus on the same detail from the zoom out
    position by moving the back plane focus ring
  • Retighten the back-plane focus knob in order to
    keep the back-plane setting

Macro focus ring
Macro release knob
Back plane focus
33
Back Panel Jacks
This panel located on the back of the camera
Video cable with bnc connector
  • Use CAM OUT for color video output, by
    connecting a bnc cable from this jack to the
    input of the video deck
  • MON OUT gives a black and white video signal
  • GL IN (for genlock in) is used for synching the
    camera in a studio situation

34
Multi-Pin Cable
  • The multi-pin cable connects directly to the
    portable video deck, and allows the camera to
    communicate with the deck for power, video signal
    and pause/record control.
  • The Power Select switch must be set to VTR in
    order to get power from the video deck

power select switch
multi-pin cable connector
This panel located on the back of the camera
35
The End
Write a Comment
User Comments (0)
About PowerShow.com