ICAO ANNEX 14 HELIPORT DESIGN WORKSHOP - PowerPoint PPT Presentation

1 / 58
About This Presentation
Title:

ICAO ANNEX 14 HELIPORT DESIGN WORKSHOP

Description:

DESIGN FOR HOVER TAXI GENERALLY REQUIRED BUT HIS MAY BE LIMITED TO SMALLER HELICOPTERS. ... BASIC AIR/HOVER MANOEUVER' STAND. 1RD (shown for reference only) ... – PowerPoint PPT presentation

Number of Views:408
Avg rating:3.0/5.0
Slides: 59
Provided by: levertonas
Category:

less

Transcript and Presenter's Notes

Title: ICAO ANNEX 14 HELIPORT DESIGN WORKSHOP


1
ICAO ANNEX 14HELIPORT DESIGN WORKSHOP

Dr John Leverton Former HAI/AHS Heliport Design
AC Focal Point IFHA Representative to ICAO
Aerodrome Panel
2
  • TAXIWAYS/TAXI-ROUTES

3
TAXIWAY/TAXIROUTEDEFINITIONS
  • CENTER SECTION (PATH) MARKED OR SEPARATE
    PAVED SECTION IS THE TAXIWAY FOR FAA AND ICAO
  • TOTAL WIDTH IS THE TAXI ROUTE FOR FAA AND ICAO
  • SECTION OUTSIDE TAXIWAY HAS DIFFERENT NAMES
    FAA TERMS THIS CLEARANCES ICAO SHOULDERS
  • WIDTH IS FUNCTION OF UNDERCARRIAGE (UC) MAX.
    WIDTH OR LENGTH AND ROTOR DIAMETER (RD) SIZE
  • THE SIZE IS IN GENERAL COMPLEX TO DETERMINE FOR
    BOTH FAA AND ICAO REQUIREMENTS/REGULATIONS
  • DESIGN FOR HOVER TAXI GENERALLY REQUIRED BUT
    HIS MAY BE LIMITED TO SMALLER HELICOPTERS. AS
    RESULT, SIZE MAY DEPEND ON LARGE HELICOPTER
    USINGGROUND TAXI.

4
Taxiways/taxi Routes
Taxiway Width
Center Line Marking/Lights
Sideline Markers or Lights
Width of Sideline Markers or Lights
FAA Rotor Tip Clearance ICAO Shoulders
Taxi Route Width
5
TAXIWAY / TAXI ROUTEHOVER TAXI
  • FAA - COMPLEX
  • AC-2B
  • TOTAL WIDTH (TAXI ROUTE) WIDTH VARYS WITH
    MARKINGS
  • ICAO USES TERM AIR TAXIWAYS
  • TOTAL WIDTH 2 RD
  • ICAO ALSO DEFINES AIR TRANSIT ROUTE (AIR TAXI
    AT HEIGHT ABOVE 30m/100ft).
  • TOTAL WIDTH 7RD FOR DAY OPERATIONS
  • 10RD FOR NIGHT
    OPERATIONS

6
TAXIWAY REQUIREMENTS - GA
7
HOVER TAXIWAYS
ICAO Annex 14
2RD
8
TAXIWAY/TAXI ROUTE(GROUND TAXI)
  • FAA REQUIREMENTS
  • NEW AC-2B
  • TAXIWAY 2 x U/C
  • TOTAL WIDTH/TAXI ROUTE MINIMUM 1RD or 35 ft
    (10.7 m) which ever is larger 20 ft.

9
TAXIWAY REQUIREMENTS - GA
10
TAXIWAY/TAXI ROUTE(GROUND TAXI)
  • ICAO REQUIREMENTS DEFINED IN TERMS OF SIZES OF
    UNDERCARRIAGE FOR RANGE OF HELICOPTER SIZES
  • e.g. for UC 4.5m TO 6m (15ft TO 35ft)
  • PAVED/MARKED TAXIWAY 10.5m (35ft) SHOULDERS
    OF ½ RD.
  • TOTAL WIDTH 1RD 10.5m (35 ft.) IF RD 50 ft
    (15 m) TOTAL WIDTH 85ft (26 m).

Extract from ICAO Annex 14
11
GROUND TAXIWAYS
New AC-2B
7.5 m / 25 ft
1/2 RD
1.5 RD
OBJECT
ICAO Annex 14
For UC up to 4.5 m(14.75 ft)
12
AC-2B Parking
Taxi Route
Offset from Taxi Route
Figure 2-14. Parking Area Design - Turn-around
Parking Positions GENERAL AVIATION
13
AC-2B Parking
14
BASIC TAXI ROUTE / TAXIWAY CONCEPT
Air Taxi-Route / Air Taxiway
Ground Taxi-Route / Ground Taxiway
0.25 RD Protection Zone
15
BASIC TAXI-ROUTE / TAXIWAY CONCEPT
Ground Taxi Route / Ground Taxiway
Air Taxiway 2UCw
0.5 RD Protection Zone
16
BASIC TAXI ROUTE / TAXIWAY CONCEPT
SLBA Static Load Bearing Area GEA
Ground Effect Area
17
BASIC STAND
STAND 2UC
STAND PROTECTION AREA 1.2 D (1.4RD)
STAND Markings NOT Shown
18
BASIC STAND
1RD (shown for reference only)
STAND PROTECTION AREA 1.2 D (1.4RD) GEA
STAND Markings NOT Shown
19
BASIC AIR/HOVER MANOEUVER STAND
0.4D (0.5RD) Protection Zone
STAND Markings NOT Shown
20
BASIC AIR/HOVER MANOEUVER STAND
1RD (shown for reference only)
STAND Markings NOT Shown
STAND Protection Zone 2D (2.4RD)GEA
21
TAXI-THROUGH STANDS
STAND Markings NOT Shown
22
TAXI-THROUGH STANDS
Air Taxi-through
2 RD
Object
0.5RD Clearance
Ground Taxi-through
1.5 RD
Object
0.25RD Clearance
STAND Markings NOT Shown
23
AIR/HOVER MANOEUVER STAND SIMULTANEOUS
OPERATIONS
STAND and Taxi Route / Taxiway Markings NOT Shown
24
AIR/HOVER MANOEUVER STAND SIMULTANEOUS
OPERATIONS
2D
2RD
STAND and Taxi Route / Taxiway Markings NOT Shown
25
AIR/HOVER MANOEUVER STAND SIMULTANEOUS
OPERATIONS
STAND and Taxi Route / Taxiway Markings NOT Shown
26
AIR/HOVER MANOEUVER STAND SIMULTANEOUS
OPERATIONS
STAND and Taxi Route / Taxiway Markings NOT Shown
27
AIR/HOVER MANOEUVER STAND SIMULTANEOUS
OPERATIONS
STAND and Taxi Route / Taxiway Markings NOT Shown
28
AIR/HOVER MANOEUVER STAND NON-SIMULTANEOUS
OPERATIONS
STAND and Taxi Route / Taxiway Markings NOT Shown
29
AIR/HOVER MANOEUVER STAND NON-SIMULTANEOUS
OPERATIONS
2 D
2 RD
NOTE Depending on the precise values of RD and
D, the Taxi Routes could overlap
STAND and Taxi Route / Taxiway Markings NOT Shown
30
AIR/HOVER MANOEUVER STAND NON-SIMULTANEOUS
OPERATIONS
STAND and Taxi Route / Taxiway Markings NOT Shown
31
AIR/HOVER MANOEUVER STAND NON-SIMULTANEOUS
OPERATIONS
STAND and Taxi Route / Taxiway Markings NOT Shown
32
FATO AIR/HOVER MANOEUVER STAND
Approach / Departure Surfaces
PC2 / PC3 GROUND LEVEL HELIPORT
NO Transitional Surfaces
FATO / STAND Markings NOT Shown
33
FATO AIR/HOVER MANOEUVER STAND
1.2D
2D
New (draft) Requirement 3.1.8 There shall be a
protected side slope at 45 from the edge of the
safety area to a distance 10 meters
FATO / STAND Markings NOT Shown
34
FATO AIR/HOVER MANOEUVER STAND
Approach / Departure Surfaces
1RD (shown for reference only)
2D
1D
2RD
1.2D
FATO / STAND Markings NOT Shown
35
FATO AIR/HOVER MANOEUVER STAND
1.2D
2D
New (draft) Requirement 3.1.8 There shall be a
protected side slope at 45 from the edge of the
safety area to a distance 10 meters
FATO / STAND Markings NOT Shown
36
FATO AIR/HOVER MANOEUVER STAND
1.2D
2D
45
10 m
FATO / STAND Markings NOT Shown
37
FATO AIR/HOVER MANOEUVER STAND
1.2D
2D
PC2 / PC3 GROUND LEVEL HELIPORT
FATO / STAND Markings NOT Shown
38
FATO AIR/HOVER MANOEUVER STAND
1D
2RD
2D
PC2 / PC3 GROUND LEVEL HELIPORT
FATO / STAND Markings NOT Shown
39
ICAO MARKINGS
  • GROUND LEVEL
  • FATO AIRPORT RUNWAY LIKE MARKING (DASHEDLINE)
    PLUS H
  • TLOF CONTINUOUS WHITE LINE 1 ft (30 cm) WIDE
  • AIMING POINT GROUND LEVEL EQUILATERAL
    TRIANGLE IF REQUIRED TO LOCATE LANDING
    POINT
  • TAXIWAY SAME AS AIRPORT (AIRPLANE) TAXIWAYS
  • ELEVATED
  • TOUCHDOWN POINT TOUCHDOWN CIRCLE

  • ALSO CALLED AIMING CIRCLE
  • YELLOW CIRCLE 0.5 D OR 20 FT (6 m) DIAMETER
  • WIDTH 20 INCHES (0.5 m)
  • REQUIRED FOR ELEVATED HELIPORTS (AND
    HELIDECKS)

40
TAXIWAY/PARKING
  • WHEELED AND SKID EQUIPPED HELICOPTERS
  • USUALLY SKID EQUIPPED MOST DEMANDING RELATIVE
    TO HELICOPTER DIMENSIONS.
  • MEDIUM/LARGE HELICOPTERS (S-76, S-61, S-92) ARE
    WHEEL EQUIPPED AND SMALL HELICOPTERS ARE
    GENERALLY SKID-EQUPPED. HENCE FOR
    TAXIWAY/PARKING FOR LARGE HELICOPTERS WHEEL
    EQUIPPED IS LIKELY TO BE MOST DEMANDING.
  • NOTE IF WHEEL EQUIPPED HELICOPTERS HOVER TAXI
    (WHEELS NOT TOUCHING SURFACE) TAXIWAY AND PARKING
    TO BE BASED ON HOVER TAXI REQUIREMENTS.

41
  • MARKINGS
  • LIGHTING

42
AIMING POINT
GROUND LEVEL
43
ICAO MARKINGS (CONT.)
  • AIR TAXIWAY
  • MARKERS AT 95 ft (30 m) FOR STRAIGHT SECTIONS AND
    48 ft (15 m) ON CURVES
  • NOT USED IN USA WAS CONSIDERED BUT DELETED FROM
    DRAFT NEW AC-2B
  • HELIPORT NAME MARKING REQUIRED
  • ELEVATED HELIPORTS MAXIMUM WEIGHT INDICATION
    RECOMMENDED
  • H WHITE HOSPITAL HELIPORTS RED H ON WHITE
    CROSS SAME AS IN FAA AC
  • NOTE H VERTICALS ALIGHTED WITH PREFERRED
    APPROACH DIRECTION H 10 FT (3 m) HIGH MIN.
    MAXIMUM NOT DEFINED- EXAMPLE GIVEN (NORMALLY
    LOCATED IN AIMING CIRCLE ON ELEVATED HELIPORT)

44
FAA TLOF MARKINGS
12 in (30 cm)
NEW AC-2B Weight (mass)/Rotor Size Limit Marking
Located in lower right-hand corner
45
HOSPITAL HELIPORT MARKING
Background NOT defined
3 m (10 ft)
Obstacle-free Sector Marking (Not discussed in
detail)
46
ICAO MARKINGSELEVATED HELIPORT
FATO/TLOF
AIMING CIRCLE (TOUCHDOWN MARKING) 1/2D Min 6
m (20 ft) DIAMETER. H 3 m (10 ft) HIGH
Mass (Weight) limit in tonnes ( i.e. 1000 kg)
FATO/TLOF for elevated heliport/helideck
47
FATO MARKING
Proposal for NON takeoff and Landing
FATO
Aiming Point Marking
Length of side 9 m (29.5 ft)
48
FATO MARKING
Proposal for FATO with TLOF
Touchdown Marking 0.5 D (commonly called
aiming circle- currently dimension only for
helidecks) Min 6 m (20 ft)
49
FATO MARKING
Proposal for FATO with TLOF ??
Touchdown Marking 0.5 D (commonly called
aiming circle- currently dimension
only defined for helidecks)
50
TLOF in HELICOPTER STAND
STAND SLB Area 2UC
TLOF SLB Area 1.5 UC
51
TLOF in HELICOPTER STAND
?
52
LIGHTING FAA AC-2B
  • COLOR FATO / TLOF NEW AC-2B- GREEN
  • CHANGED FROM YELLOW IN AC-2A
  • FATO OR TLOF
  • GENERAL AVIATION 4 PER SIDE (25FT MAX.
    INTERVAL).
  • FATO RAISED OR FLUSH
  • NEW AC -2B FLUSH LIGHTING ONLY FOR GROUND LEVEL
    TLOF.
  • FLOODLIGHTS ALLOWED
  • ELEVATED MOUNTED ON TLOF OR FATO SAFETY NET
  • HELIPORT INDENTIFICATION BEACON- GENERAL AVIATION
    OPTIONAL
  • TAXIWAY LIGHTS NO REAL CHANGE BUT MORE DETAILED
  • UNLESS NEAR AIRPORT RUNWAY LIGHTS WHEN YELLOW
    LIGHTS CAN BE USED.

53
ICAO LIGHTING
  • GROUND LEVEL FATO
  • ONLY REQUIRED IF FATO IS NON-EVIDENT
  • SQUARE / RECTANGULAR INTERVAL OF NOT MORE THAN
    50m (164 ft) MINIMUM 4 PER SIDE WITH ONE (1) AT
    EACH CORNER.
  • CIRCULAR INTERVAL OF NOT MORE THAN 5m (16ft)
    WITH MINIMUM OF 10.
  • COLOR WHITE
  • GROUND LEVEL TLOF
  • PERIMETER LIGHTS OR FLOODLIGHTS
  • SQUARE / RECTANGULARE INTERVAL OF NOT MORE THAN
    5m (16 ft) MINIMUM 4 PER SIDE WITH ONE (1)
    AT EACH CORNER
  • CIRCULAR EVENLY SPACED IF NOT POSSIBLE
    INTERVAL OF NOT MORE THAN 45 Degrees - WITH
    MINIMUM OF 14.
  • COLOR GREEN
  • ASSUMES LARGE FATO!

54
NEW ICAO LIGHTING REQUIREMENTS
  • NEW ICAO REQUIREMENTS ADOPTED IN 2004 FOR
    ELEVATED HELIPORTS AND HELIDECKS
  • CHANGE FATO/TLOF PERIMETER LIGHTS FROM YELLOW TO
    GREEN
  • LIGHT / IDENTIFY TOUCHDOWN MARKINGS USING
    ASPSL AND/OR LPs AND/OR FLOODLIGHTING i.e.
    LIGHT OR ILLUMINATE AIMING CIRCLE AND H.
  • LIGHTS MAY ILLUMIATE THE WHOLE SHAPE OR JUST
    THE OUTLINE SHAPE. RECOMMENDATION FOR THE
    AIMING CIRCLE - BROKEN (DASHED) CIRCLE OF
    YELLOW ASPSL LIGHTS ON OUTER EDGE PROPOSED, FOR
    THE H- GREEN LPs.
  • ASPSL ARRAY OF SEGMENTED POINT SOURCE LIGHTS
  • i.e. STRIPS OF LIGHT EMITTING
    DIODES (LEDs)
  • LP LUMINESCENT PANEL LIGHTS

55
ICAO LIGHTING
  • ELEVATED FATO / TLOF
  • GREEN PERIMETER LIGHTS AND ARRRAYS OF SEGMENTED
    POINT SOURCE LIGHTING (ASPSL) AND/OR LUMINESCENT
    PANELS (LPs).
  • PERIMETER LIGHTS
  • INTERVAL 3m (10ft)
  • MAX HEIGHT 25cm (10 in)
  • INSET LIGHTS WHEN ... EXTENDING ABOVE SURFACE
    COULD ENDANGER HELICOPTER
  • DETAILS FOR LUMINESCENT PANEL LIGHTS
  • FATO / TLOF COINCIDENTAL (SAME SIZE) FOR
    ELEVATED HELIPORTS AND HELICDECKS

56
NEW ICAO LIGHTING REQUIREMENTS
CAA Photograph
57
LIGHTING ISSUES
  • SAFETY CONCERNS OVER USE OF LIGHTS WITH-IN FATO
    (i.e TO LIGHT TLOF and/or TOUCHDOWN CIRCLE) WHEN
    SKID HELICOPTERS ARE USED.
  • ARE ADDITION VISUAL CUES REQUIRED? - DOES
    ADDITIONAL LIGHTS PROVIDED THE NESCESSARY
    VISUAL CUES?
  • COST
  • IS GREEN LIGHTS THE BEST FOR LOCATING HELIPORTS
    UNDER ALL AMBIENT LIGHT/ WEATHER CONDITIONS?

58
End of this section . MORE TO COME
Write a Comment
User Comments (0)
About PowerShow.com