Title: AV/Xerox
1AV/Xerox
- On your way to being real nerds
2Audio/Visual Equipment
- Every Carbarn classroom is the same!
- Note The projectors are controlled by the
opposite side of the remote (when working them,
think of which side it would be when you face the
BOARD) - Equipment in Carbarn Classrooms
- Wireless Lapel Microphone
- Laptop Connections
- Visualizer
- Projector and Screens
- Wireless Mouse
- PC (with DVD player)
- Projector/Screen Remote
- VCR
3Equipment Description
- Wireless Lapel Microphone
- Very strong and works all over room!
- Kept in Slot Under Flap on Left Side of Desk
- Not working?
- Check Volume 1st
- Check Battery (takes 9V)
4Equipment Description
- Laptop Connections
- Kept in Slot Under Flap on Left Side of Desk
- Audio Plug
- VGA Port (for video monitor connection thing.)
5Equipment Description
- Visualizer
- Same as overhead projector, just digital and way
cooler. - Uses a digital camera to relay anything on its
table. - Can fold away (another way to focus!)
- Not working?
- Check Power and Video Cable
6Equipment Description
- Wireless Mouse
- Can wave it around, but also works on surfaces.
- To use pull trigger, wave in air.
- Works all over room!
- Not working?
- CHARGE BATTERY!! It has to lay in its cradle
completely. (Some Profs dont remember this)
7Equipment Description
- PC
- On Left Under Podium
- Where You Can Play DVDs
- DONT MOVE PC!! This can disconnect the wires and
thats a BIG problem.
8Equipment Description
9Right Side Under Podium Stuff
Master Switch! (Turns everything on/off)
Audio On/Off
VCR
SHURE receiver needs to be ON, can tweak
squelch here.
Outputs 1 and 5 should be selected. i/o both
have to be lit (its video audio)
AXLINK and AXCENT brains of the operation,
wont need to mess with Them.
Master Volume
Power
These switches work best when all slightly to
left!
These two switches should be OFF
10Equipment Description
- Remote
- This piece is particularly expensive. As a
precaution, Cleve has created the PC Touch
Program which will be the 1st thing to pop up
when logging in (its a digital representation of
the remote!).
11Equipment Description
- PC TOUCH! Its the same as the remote, but on
the computer. Neat, huh.
12PC Touch and Remote Functions
You can lower or raise the screens from here.
Can also do this at the keypad next to the
whiteboard (on the left side when facing
board.)
Heres where you turn on and off the projectors.
Select the PC
Select Visualizer
VCR controls (play, pause, etc.)
AUX 1 is for laptops!
Select VCR
AUX 2 and 3 do nothing!
Volume?
13Things to Remember
- Projectors take a minute to warm upif a red
light comes on, thats bad. But only let the
full time staff touch it!! - On PC Touch
- Master volume has to be up in order to turn this
volume up too! - No way to split volume this volume on PC Touch
turns EVERYTHING up or down.
14XEROX!
15XEROX!
- While theres a lot of information, here is what
we think is the most important for you to know - Jam Clearance
- Image Adjustment Tab
- Multi-up
- Annotation
- Interrupt and Deleting Jobs
16Jam Clearance
17Jam Clearance
- All areas you can open have an exclamation point!
- All jam areas are in GREEN (see arrows)
- Consumables (ex. Toner) are in ORANGE
- Toner is NOT interchangeable. The cap should be
BLACK. - Toner collection bottle in area 1 replace (or
dump) when you replace toner. - Dark smudges? Clean Xerographic module (the
little button looking thing).
18Image Adjustment Tab
- Image Quality good for copying photo IDs!
Can lighten or darken, as well as half-tone (good
for magazine or book pictures). - Bound Originals Put book spine in middle of
glass (there is a picture of a book there). - Can select which side to copy!
- There is also a binding erase feature.
19Image Adjustment Tab
Bound Originals
Image Quality
20Multi-Up
- In Output Format Tab
- Allows proof of four pages of what youre copying
on one printed page. - Good for multiple pages on one sheet for big jobs!
21Annotation
- Also in Output Format Tab
- Where you can select to put page numbers or the
date on your job automatically.
22Output Format Tab
Multi-Up
Annotation
23Interruption and Deleting Jobs
- Interrupt Pauses big job so that someone else
can copy, then will finish big job when you press
interrupt button again. - Job Status Button Where you can see all the
jobs lined up and/or completed. - This is where you can delete jobs.
- Use this when the STOP button does not work.
24Interruption and Deleting Jobs
Usually features selected, but heres job status!
Interrupt!
STOP.
Machine status (for finding serial number)
25Remember
- After 60 seconds, the machine will return
everything to default. - Master power is behind front door on machine (top
right). - If asked for the serial number (for help calls,
etc.), you can find it in Machine Status or
under the touch screen behind the front door of
machine.