Adding to your

1
(No Transcript)
2

• Adding to your
• Diagnostic Station

3
Adding to your ADC Adview

• You can add functions to your diagnostic
  station. Click on the module that you want to add
• Pulse oximetry
• Thermometry
• Or let us know what modules you would like to
  have by leaving us feedback at
• www.adctoday.com

4
Adding thermometry

• The temperature module attaches to the top of
  the BP module. It is made up of the following
  two pieces

Display (Part A)
Holder/Well (Part B)
5
Adding thermometry

1. Using the power button on the right side of the
   BP module, ensure that the ADC Adview is off.
2. Remove the cover plate from the top of the BP
   module.

6
Adding thermometry

1. Slide part A of the temperature module along the
   guides on the top of the BP module from front to
   back until it snaps into place. All the segments
   of the temperature module display will light when
   the modules have been connected correctly.

Display (Part A)
Holder/Well (Part B)
Display (Part A)
7
Adding thermometry

1. Attach the temperature probe connector to part B
   as follows with the black surface facing
   downward, hold the probe connector end against
   the notches on the probe holder, as shown in red.

8
Adding thermometry

1. Rotate the connector upwards until it snaps
   securely into place. The black surface faces
   outward and the cord extends upward.

9
Adding thermometry

• Slide part B onto part A as shown (this connects
  the temperature probe connector to the
  temperature unit connector), and insert the
  temperature probe into the well.

Holder/Well (Part B)
Display (Part A)
10
Synchronizing the modules

• Turn the device on using the power button on the
  right side of the BP module. At the end of the
  start-up sequence, the temperature module display
  will blank except for the appropriate temperature
  unit icon (F or C). A short beep indicates
  that the ADC Adview is ready.
• Refer to the ADC Adview users manual for
  operation, maintenance and safety instructions.
• Need help?

11
Changing the unit of temperature measurement

• Using the end of a paper clip or similar tool,
  press the recessed button on the temperature
  module. The icon for the selected unit is
  displayed.

12
Adding pulse oximetry

• The pulse oximetry module attaches to the
  bottom of the BP module. Included in the Pulse
  Oximetry Module kit are the pulse oximetry
  module, the adult reusable sensor, and a 6
  extension cable.

13
Adding pulse oximetry

1. Using the power button on the right side of the
   BP module, ensure that the ADC Adview is off.
2. Remove the cover plate from the bottom of the BP
   module.

14
Adding pulse oximetry

1. Slide the pulse oximetry module along the guides
   on the bottom of the main BP module from front to
   back until it snaps into place. All the segments
   of the pulse oximetry module display will light
   when the modules have been connected correctly.

15
Adding pulse oximetry

1. Turn the device on using the power button on the
   right side of the BP module. At the end of the
   start-up sequence, the pulse oximetry module
   display will blank except for the SpO2 symbol.
2. Turn the device off, connect the adult reusable
   sensor to the 6 extension cable, and then the
   cable to the connector on the module. Secure the
   cable to your device using the retention clip.

16
Synchronizing the modules

• Turn the device on. All display segments light
  up for three to five seconds. A short beep
  indicates that the ADC Adview is ready.
• Refer to the ADC Adview users manual for
  operation, maintenance and safety instructions.
• Need help?

17
Need help?

• Contact us by telephone
• 1.800.232.2670 or 1.631.273.9600
• Or by email
• CustomerService_at_adctoday.com
• Or find help on the Internet
• www.adctoday.com