Planning and Placing Concrete

1

• Planning and Placing Concrete

2
Next Generation Science/Common Core Standards
Addressed!

• CCSS.ELA Literacy. RST.9-10.3 Follow precisely a
  complex multistep procedure when carrying out
  experiments, taking measurements, or performing
  technical tasks, attending to special cases or
  exceptions defined in the text.
• CCSS.ELA Literacy. RST.9- 10.5Analyze the
  structure of the relationships among concepts in
  a text, including relationships among key terms
  (e.g., force, friction, reaction force, energy).
• CCSS.ELA Literacy. RST.11- 12.3 Follow precisely
  a complex multistep procedure when carrying out
  experiments, taking measurements, or performing
  technical tasks analyze the specific results
  based on explanations in the text
• CCSS.ELA Literacy. RST.11-12.4 Determine the
  meaning of symbols, key terms, and other
  domain-specific words and phrases as they are
  used in a specific scientific or technical
  context relevant to grades 1112 texts and
  topics.
• CCSS.Math.Content.HSGCO.D.12 Make formal
  geometric constructions with a variety of tools
  and methods (compass and straight edge, string,
  reflective devices, paper folding, dynamic
  geometric software, etc.). Copying a segment
  copying an angle bisecting a segment bisecting
  an angle constructing perpendicular lines,
  including the perpendicular bisector of a line
  segment and constructing a line parallel to a
  given line through a point not on the line

3
Bell Work / Student Learning Objectives

• Describe how to plan the outlined job provided
  by your instructor.
• Discuss preparation for the concrete pour.
• Explain placing, finishing, and curing concrete.

4
Terminology

• Bag mix
• Broom finish
• Bull float
• Calcium chloride
• Coarse aggregate
• Concrete
• Concrete drag
• Concrete edger
• Concrete form
• Concrete jointer
• Curing

• Darby
• Earthen form
• Fine aggregate
• Float finish
• Floating
• Form nails
• Gallon mix
• Magnesium or wooden hand float
• Portland cement
• Power trowel

5
Terminology

• Reinforcing bars
• Reinforcing wire
• Steel hand concrete finishing trowel
• Striking off
• Troweled finish

6
Anticipated Problem

• What do you need to know before pouring concrete?

7
Concrete

• Is a mixture of coarse aggregate, fine aggregate,
  portland cement, and water.

8
Concrete

• Coarse aggregate Gravel
• Fine aggregate Coarse sand
• Portland cement Cement made from burning lime,
  silica, iron oxide, and alumina together.
• Gypsum is then added, which acts as a glue that
  holds everything together

9
Cubic Yards

• Concrete is figured and sold by the cubic yard
• Commonly drop the word cubic and refer to
  concrete by the yard
• To calculate the amount needed convert the
  length, width, and thickness into feet, multiply
  them together, and divide by 27
• One cubic yard is 27 cubic feet.

10
Cubic Yards

• For example a concrete driveway 18 foot 30 foot
  poured six inches thick would be 10 cubic yards
  (18 30 .5 27 10 cubic yards).

11
Selecting Materials

• Use quality materials
• If soil is present in the sand or gravel, the
  result will be weak concrete
• Use clean washed sand

12
Mixing Ingredients

• Mix in correct proportions
• Driveways, walks, floors, and watertight
  foundations should be a six gallon mix
• Foundation walls, footing, and mass concrete can
  be a seven gallon mix.

13
Mixing Ingredients

• Gallon mix Number of gallons of water used with
  a bag of cement.
• Less water means stronger concrete

14
Mixing Ingredients

• Bag mix Number of bags or sacks of cement used
  per cubic yard of concrete.
• Example Six bag mix - Six bags of cement per
  cubic yard
• Correct proportions for a six bag mix
• One part cement to 2¼ parts fine aggregate to 3
  parts coarse aggregate.

15
(No Transcript)
16
(No Transcript)
17
Planning

• Purchase material to build concrete forms
• Assembling tools needed for
• Digging,
• Building and setting forms,
• Installing reinforcement,
• Pouring concrete, and
• Finishing concrete

18
Anticipated Problem

• What do I need to do before the concrete arrives?

19
Preparation

• Concrete may be mixed
• In a wheelbarrow using a shovel or
• Shoveled into a small electric or gasoline
  powered mixer
• Most people purchase ready-mixed concrete from a
  local supplier.

20
Digging

• In many cases the area where concrete is to be
  poured or placed must be dug out.
• Example Driveways and sidewalks are generally
  one inch above the ground level when finished.
• Small areas A shovel may be used

21
Digging

• Larger areas need a backhoe, grader blade, or
  loader bucket to speed up the job
• In some cases, like a floor, the concrete should
  be level while in other situations, like a
  driveway, the concrete should slope away from the
  house

22
Forms

• Concrete form Frame or mold that holds wet
  concrete in shape until it has set or hardened.
• The forms must be strong and rigid to prevent
  sagging, bulging, and spreading

23
Forms

• Freshly poured concrete exerts great pressure
• Earthen form Trench dug in the ground with solid
  walls
• Used for concrete footing

24
Foundation Footing!
25
Forms

• When wooden forms are used they must be tight to
  prevent the escape of the water-cement paste
• A tightly stretched nylon line is useful to set
  the forms in a straight line
• Wooden stakes are used to hold the form boards in
  position

26
Forms

• Small jobs Four foot level on top of the form
  can be used to set the forms level or sloping
• Surveying level Needed to set larger jobs.

27
Forms

• Form nails (or scaffold nails) Double-headed
  nail used to fasten the boards to the stakes
• Coating forms with used motor oil or diesel fuel
  and using form nails make form removal much easier

28
Fill

• Fill sand or rock should be added if the area is
  too deep.
• Drag board can be used as fill is added so that
  the recommended thickness of concrete will be
  poured

29
Fill

• Fill, especially sand, should be packed or tamped
  down so that it is solid.
• Do not use soil as fill because it will
  settle later leaving a void or hole
  under the concrete which will allow slab movement.

30
Plastic

• Place sheet of plastic on top of the pour if the
  weather is very warm and you would like to slow
  down drying and curing time
• Also concrete floors with plastic under them are
  less likely to be damp.

31
Reinforcing Bars and Wire

• If heavy equipment will drive over concrete or
  freezing and thawing will be a problem, concrete
  should be reinforced
• Reinforcing bars Steel bars with ridges that
  bond with the concrete
• Commonly seen in the construction of highways and
  bridge decks

32
Reinforcing Bars and Wire

• Reinforcing wire Rolls with wire rectangles or
  squares approximately 6 inches on center
• Used in lighter construction such as patios and
  sidewalks.
• Metal is used because it expands and contracts at
  the same rate as hardened concrete

33
(No Transcript)
34
Hot Weather

• Consider spraying the area to be poured with
  water when the concrete arrives

35
Moisture Content

• Be sure there are no dry clumps and the concrete
  is thoroughly mixed whether you mix or buy
  ready-mixed.
• Water content is very important

36
Moisture Content

• Extra water will result in weak concrete but
  concrete that is too dry is very difficult to
  pour and level off. It may also leave voids with
  exposed coarse aggregate.
• Watch experienced concrete finishers or hire one
  to help the first time you pour concrete.

37
Fiberglass fibers

• May be added to the concrete as it is mixed at
  the ready-mix plant as a way to reinforce it.

38
Calcium Chloride

• If concrete is poured in cold weather calcium
  chloride is added to prevent the concrete from
  freezing as it cures
• Building paper or straw can be used to cover the
  concrete after it is finished and while it is
  curing

39
Anticipated Problem

• How is concrete placed, finished, and cured?

40
Placing and Finishing concrete

• Should not be attempted without having plenty of
  labor
• After concrete is mixed the drying and curing
  process begins you are working against the clock
• Be sure all placing and finishing tools are on
  hand

41
Moving and Spreading Concrete

• Common tools used to move and spread material
• Shovels,
• Spades,
• Rakes, and
• Concrete drags
• Floats and trowels

42
Moving and Spreading Concrete

• Since concrete is so heavy Move it downhill with
  a chute
• Closer the concrete chute is to where the
  concrete is needed, the less work is required
• Areas where the chute cannot reach use
  wheelbarrow
• Concrete should be pushed, pulled, or lowered
  rather than lifted

43
Moving and Spreading Concrete

• Concrete drag Solid blade with a handle used to
  push or drag concrete into low spots
• Striking off Using a drag board that is usually
  a 2 4 or a 2 6 that is used to saw back and
  forth to level the concrete.

44
Moving and Spreading Concrete

• Work team for placing concrete
• One person needed at each end of the drag board
• Third person with rubber boots and a concrete
  drag in middle of the concrete make a good team
  for placing concrete
• Other workers are needed to operate the
  wheelbarrows and shovels

45
Moving and Spreading Concrete

• A drag board vibrator can be clamped to two drag
  boards
• One person with the drag board vibrator can do
  the same work as two people without it.
• The concrete should be dragged twice before going
  on to the next step.

46
(No Transcript)
47
Moving Fine Material

• To vibrate the fine material next to the form
  board
• Hammer Used to tap the form boards
• Spade Used to jab up and down inside the form
  board

48
Floating

• Pushing the rocks down and bringing sand-cement
  paste to the surface and beginning the smoothing
  process
• Magnesium or wooden hand float Used to smooth
  the area near the edge of the work area
• Use a semi-circular motion when using a hand
  float.

49
Floating

• Darby Two handed float usually 18 long that is
  also used near the edge
• Bull float 36 or 42 inch float with long round
  handle used to reach areas away from the edge

50
Rounding the Edge

• Concrete edger Used to push rocks down near the
  form board to round the edge
• Prevents a chipping or breaking when the form
  board is removed

51
Grooving

• Concrete jointer Used to put grooves across
  concrete areas like sidewalks
• Joints help the appearance and provide relief
  area for expansion and contraction
• Makes cracks in concrete less noticeable

52
Finishing Concrete

• Float finish Leaves rough finish
• acceptable for a livestock feeding floor or
  footing
• Troweled finish Very smooth finish
• Used home, business and garage floors

53
Finishing Concrete

• Steel hand concrete finishing trowel Used for
  small jobs and near the edge on large jobs.
• Use in a semi-circular motion much like floating
  except
• greater pressure is
• needed.

54
Finishing Concrete

• Power trowel Gasoline powered trowel with three
  or four blades
• Used to finish large areas

55
Finishing Concrete

• Broom finish Made by using a coarse bristle
  concrete broom or floor broom either after
  floating or after troweling
• Often used on driveways and sidewalks for added
  traction

56
Curing

• Process of concrete drying and hardening.
• Slower the moisture leaves, the stronger the
  concrete will become.

57
Curing

• Helpful Hints
• Spray concrete with water every day of the first
  week
• Covering the concrete with plastic or a tarp
• Allow the concrete to cure for at least 7 days
  prior to driving vehicles on it.

58
Review / Summary

• Describe how to plan the job.
• Discuss preparation for the concrete pour.
• Explain placing, finishing, and curing concrete.

59
The End!