SAFETY FIRST

1
SAFETY FIRST
2
(No Transcript)
3
(No Transcript)
4
(No Transcript)
5
(No Transcript)
6
(No Transcript)
7
(No Transcript)
8
General Safety Policies

• All students must wear clothing suitable to the
  activity (shop coats, aprons, or school clothes).
• Students must remove or securely fasten neckties,
  jewelry, loose clothing, long hair, etc.
• Students must wear approved safety eye protection
  at all times while in a laboratory, except in
  safe areas as designated by the instructor.

9

• All guards and other safety equipment must be in
  place and operating correctly.
• Students must at all times have permission from
  the instructor to work in the laboratory.
• Everyone should know where and how to find first
  aid.
• A running machine must never be left unattended.

10

• Accident reports must be filled out on all
  injuries and on near injuries as well.
• All material and equipment damage must be
  reported.
• No student may use any machine on which he-she
  has not been properly instructed.
• There must be at least two people present in the
  laboratory.

11

• The work area and work surfaces should be kept
  clean
• of scraps,
• liquids, and
• unnecessary
• equipment.
• No horseplay
• or
• roughhousing
• is allowed in the laboratory or shop.

12
Safety for portable power tools

• KNOW YOUR POWER TOOL Read instructions
  carefully. Learn its applications and
  limitations as well as the specific potential
  hazards of using this tool.
• GROUND ALL TOOLS UNLESS DOUBLE-INSULATED If
  tool is equipped with three-prong plug, it should
  be plugged into a three-hole electrical
  receptacle. If adapter is used to accommodate
  two-pronged receptacle, the adapter wire must be
  attached to known ground. Never remove third
  prong.

13

• KEEP GUARDS IN PLACE and in working order.
• KEEP WORK AREA CLEAN. Cluttered areas and benches
  invite accidents.
• AVOID DANGEROUS ENVIRONMENTS. Dont expose power
  tools to rain or use in damp, wet, or gaseous or
  explosive locations. Keep work are well lit.

14

• STORE IDLE TOOLS. When not in use, tools should
  be stored in dry, locked-up place.
• DONT FORCE TOOL. It will do the job better and
  safer at the rate for which it was designed.
• USE RIGHT TOOL. Dont force small tool or
  attachment to do the job of a heavy-duty tool.

15

• WEAR PROPER APPAREL. No loose clothing or jewelry
  to get caught in moving parts. Rubber gloves and
  footwear are recommended when working outdoors.
• USE SAFETY GLASSES with most tools. Also face or
  dust mask if cutting operation is dusty.

16

• DONT ABUSE CORD. Never carry tool by cord or
  yank it to disconnect from receptacle. Keep cord
  from heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work.
  Its safer than using your hand and it frees both
  hands to operate tool.
• DONT OVERREACH. Keep proper footing and balance
  at all times.

17

• MAINTAIN TOOLS WITH CARE. Keep tools sharp and
  clean at all times for best and safest
  performance. Follow instructions for lubricating
  and changing accessories. CAUTION Do not use
  carbon tetrachloride.
• DISCONNECT TOOLS. When not in use before
  servicing when changing accessories such as
  blades, bits, cutter, etc.

18

• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of
  checking to see that keys and adjusting wrenches
  are removed from tool before turning it on.
• AVOID ACCIDENTAL STARTING. Dont carry plugged-in
  tools with finger on switch. Be sure switch is
  off when plugged in.
• WEAR EAR PROTECTORS when using for extended
  periods.

19

• ACCESSORIES. The use of any accessories other
  than those listed or recommended for this
  particular tool may be hazardous.
• KEEP HANDS AWAY FROM CUTTING EDGES AND ALL MOVING
  PARTS.