Goodson Tools and Supplies for Engine Builders

1
GoodsonTools and Supplies for Engine Builders

• Keeper-Eeze Tools

2
Keeper- Eeze Tools
KE-6802
KE-6940
KE-6902
KE-6901
KE-6804
KE-6903
3
Keeper-Eeze Demonstrated on Honda CRF-250R
4
Valve Support Selection A Shot-Bag or Chamber
Plug must be used to hold up the valves while
removing the valve locks.

• The Shot-Bags will conform to the combustion
  chamber. They should not protrude too far from
  the deck surface when installed. Choose from the
  different size bags for the correct fit. Multiple
  bags can be used for large chambers.

5
Sleeve Selection

• Determine the correct protective guide Sleeve.
  Pick the Sleeve that fits closest to the bucket
  bore dia. And the spring/ retainer assembly. Some
  engines require the valve spring clearance relief
  to be used as a guide.

ID always fits tool
6
Installing Sleeve

• Fits in around spring retainer
• Install the correct size sleeve over the spring
  retainer assembly. The sleeve will maintain the
  proper fit for removal and assembly of the spring
  retainer.

7

• This shows the proper sleeve installed around the
  spring and retainer.

8
T-Handle Assembly

• Hold the T-handle portion of the Keeper-Eeze tool
  with the tube down between the fingers. Remove
  any Loader Modules from the tool by gently
  pulling on the plunger at the end to overcome the
  magnetic force. Retract the Adjuster by loosening
  the knob on the side and pulling it back.

9

• Insert the Remover attachment (Order No. KE-6803)
  into the end of the Keeper-Eeze tool. Push it in
  with a twisting action until it is fully seated.

10
Push tool down

• Insert T Handle in sleeve installed in step 3.
  Hold tool down with one hand and firmly strike
  the T-Handle with palm of the opposite hand. This
  will release keepers. (Do not strike Keeper-Eeze
  with a hammer)

11
Lock and retainer held by remover

• Pull the tool away from the cylinder head. The
  valve locks and retainer will be held safe by the
  Remover. Store the components for later assembly.

12

• Remove valve lock Retainer off of the magnet
  with your hand

• Remove Spring

13

• Remove valve

14
To Reassemble

• Install retainer on top of valve spring

• Install valve spring

15

• Spring Assembly
• in place

• Install Sleeve

16

• Insert the installation attachment into the
  T-handle

• Now the installation attachment is ready to have
  the correct keeper loader installed into the end
  of the installation attachment

17
Assembly

• Insert the correct size loader module with the
  correct loader that matches the valve stem
  diameter until it seats up against the magnet

18
Fully Assembled

• Loosen adjustment knob on side of
  T-handle. Then adjust loader module pin to
  approximately the same depth the keepers are
  located down on the valve stem.

19

• Keepers are in position to be installed in the
  retainer and valve stem

• Place the valve locks (keepers) on the Loader
  Plunger

20

• Same as removal, push down on T-handle Until an
  audible click is heard and felt in the handle
  and snaps in place and then remove T-handle

• Now insert into the top of the sleeve and push
  into the retainer

21

• Remove outer sleeve and you have a finished
  product

22
Keeper- Eeze Tools
KE-6802
KE-6940
KE-6902
KE-6901
KE-6804
KE-6903
23
GoodsonTools and Supplies for Engine Builders

• Keeper-Eeze Tools
• Any questions on the Keeper- Eeze please contact
  us
• Toll Free 1-800-533-8010
• Phone [phone]
• Website
• www.goodson.com