How to configure DCN Wireless

1
How to configure DCN Wireless Stand Alone
Camera Control

• This presentation is intended to guide the
  installer step by step through camera control
  installation.

DCNW CC
2
How to configure DCN Wireless Stand Alone
Camera Control

• DCN-WCCU with direct Camera Virtual Keyboard
• DCN-WCCU with direct Camera Control Autodome
  Controller
• DCN-WCCU with Allegiant Video Switcher

3
DCN-WCCU with direct Camera Virtual Keyboard

• Requirements
• One AutoDome Camera
• One monitor
• Virtual keyboard software LTC 5138/00
• DCN-WCCU
• Temporary Installation PC
• Camera Control Software LBB 4162/xx

4
Step 1

• Connect PC and Monitor to the Dome Camera

Make sure that the Dome camera has an address.
RS232
Temporary Installation PC
IU Instructions
5
Step 2

• Install virtual keyboard software LTC 5138/00

Temporary Installation PC
IU Instructions
6
Step 3

• Configure Virtual Keyboard

7
Step 4

• Communication Setup

8
Step 5

• Make sure you choose the right camera!!

9
Step 6
10
Step 7

• Quick Commands settings

11
Step 8

• Pre-Position Title Set

12
Step 9

• Set Pre-Positions

13
Step 10
14
Repeat
Repeat Step 9 10 to set all Pre-Positions
Set the highest Pre-Position as overview
15
Step 11

• Check the Pre-Positions

To NEXT gtgtgtgtgtgt
16
End of how to configure

• DCN-WCCU with direct Camera Virtual Keyboard
• DCN-WCCU with direct Camera Control Autodome
  Controller
• DCN-WCCU with Allegiant Video Switcher

17
DCN-WCCU with direct Camera Control Autodome
Controller

• Requirements
• One AutoDome camera
• Monitor(s)
• Autodome Controller LTC 5136/51
• DCN-WCCU
• Temporary Installation PC
• Camera Control Software LBB 4162/xx

18
Step 1

• Only for Pre setting the Autodome Camera with
  the Autodome Controller
• Connect Autodome Controller to data converter LTC
  5136/51
• Connect Data converter to Aurodome Camera
• Connect Autodome Camera to Monitor

Data Converter
Temporary Autodome Controller
IUI Autodome
19
Remark

• If you were not successful setting up the
  pre-positions please dont continue with the next
  steps.
• First make sure that the pre-positions are set.

20
Step 2

• Connect DCN-WCCU to PC

RS232
Temporary Installation PC
Port 2 Camera Control Protocol Baudrate 9.6K
IU Instructions
21
Step 3

• CCU protocol and Serial Port settings DCN-WCCU

Make sure that the ports of the CCU are set
correct.
Port 1Protocol FullBaudrate 115.2K Port
2Protocol Camera ControlBaudrate 9.6K
S500 Dip switches
Keep in mind !!
You have to change the baudrate of Port 2 to 9.6K
!!
IU Instructions
22
Step 4

• Make sure you connect the RS232 cable to Port 2
  of the DCN-WCCU.

23
Step 5

• Install DCNNG Stand Alone Camera Control software
  LBB4162

24
Step 6

• Install Camera Control software LBB4162

25
Step 7

• Install Camera Control software LBB4162

26
Step 8

• Install Camera Control software LBB4162

27
Step 9

• Select the language for operator

28
Step 10

• Select no use of Allegiant VideoSwitcher

29
Step 11

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

30
Step 12

• Finish installation

31
Step 13

• Start DCN Next Generation Camera Install

32
Step 14

• Combine seat numbers with camera pre positions

LBB4162
33
Step 15

• Make sure you choose the right camera!!Camera nr
  Camera Address

LBB4162
34
Step 16

• Insert

LBB4162
35
Step 17

• Stop Camera Installation

LBB4162
36
Step 18

• Connect DCN-WCCU to AutoDome Camera

RS232
Port 2 Camera Control Protocol Baudrate 9.6K
Baudrate 9.6K
IU Instructions
37
End of how to configure

• DCN-WCCU with direct Camera Control Autodome
  Controller
• DCN-WCCU with Allegiant Video Switcher

38
DCN-WCCU with Allegiant Video Switcher

• Requirements
• Allegiant switcher
• Video Switcher keyboard
• Fixed and/or AutoDome cameras
• Monitor(s)
• DCN-WCCU
• Temporary Installation PC
• Camera Control Software LBB 4162/xx

39
Step 1

• Connecting system hardware

BOSCH
Temporary Installation PC
40
Step 2

• Connect DCN-WCCU Allegiant Switcher to
  Temporary PC

Port 2 Camera Control Protocol
RS232
RS232
Allegiant Switcher
Baudrate 19.2K
Baudrate 19.2K
IU Instructions
41
Step 3

• CCU protocol and Serial Port settings DCN-WCCU

Make sure that the ports of the CCU are set
correct.
Port 1Protocol FullBaudrate 115.2K Port
2Protocol Camera ControlBaudrate 19.2K
S500 Dip switches
IU Instructions
42
Step 4

• Make sure you connect the RS232 cable to Port 2
  of the DCN-WCCU.

43
Step 5

• Install DCNNG Stand Alone Camera Control software
  LBB4162

44
Step 6

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

45
Step 7

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

46
Step 8

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

47
Step 9

• Select the language for operator

48
Step 10

• Select use Allegiant VideoSwitcher

49
Step 11

• Installing DCNNG Stand Alone Camera Control
  software LBB4162

50
Step 12

• Finish installation

51
Step 13

• Set Pre-Positions using the Video Switcher
  Keyboard

52
Step 14

• Start DCN Next Generation Camera Install

53
Step 15

• Combine seat numbers with camera pre positions

LBB4162
54
Step 16

• Make sure you choose the right camera!!Camera nr
  Camera Address

LBB4162
55
Step 17

• Insert

LBB4162
56
Step 18

• Stop Camera Installation

LBB4162
57
Step 19

• Connecting hardware (Remove temporary PC!)

See next slide
BOSCH
58
Step 20

• Connection cable between DCN-WCCU and Allegiant
  Switcher

IU Instructions
59
End of how to configure

• DCN-WCCU with Allegiant Video Switcher

DCNW CC