Material Handling and Storage

1
Material Handling and Storage

• Occupational Health and Safety
• November 7, 2005

2
Objectives

• Recognize material handling hazards
• Manual material handling
• Industrial trucks
• Conveyors
• (Cranes will be addressed later)
• Become familiar with basic methods of controlling
  these hazards

3
Material Handling and Storage

• Outline
• Introduction
• General Practices
• Storage
• Manual Material Handling
• Powered Industrial Trucks

4
Introduction

• 600,000 overexertion injuries, 27 of all lost-
  workday cases
• 370,000 injuries caused by lifting
• 93,000 pushing/pulling
• Strains and sprains from loads that are too heavy
  or large
• Fractures, cuts and bruises from improper storage
• 100 annual deaths from Powered Industrial Trucks
  (forklifts)

5
Introduction

• General Work Practices
• Get help for large loads or use mechanical
  devices
• When blocking a raised load
• Keep hands from underneath before releasing load
• Use blocking materials of adequate strength
• Look for cracks, splintered pieces, rounded
  corners, etc.
• Attach handles or holder to loads
• Use appropriate PPE
• Gloves, eye protection, safety boots (for heavy
  loads)

6
Introduction

• General Work Practices (cont.)
• Do not overload equipment
• Refer to equipment rated capacity
• General forklift procedures
• Center load on forks and close to mast
• Do not overload
• Do not add extra weight to counterbalance
• Travel with load at lowest position

7
Materials Storage

• Precautions for stored materials
• Stacked loads correctly piled and cross-tiered
• Stored material must not create hazard
• Areas free of accumulated material
• In buildings, no stored materials within 6 feet
  of hoist ways or 10 feet of exterior building
  walls
• Store non-compatible material separately

8
Materials Storage

• Stored material precautions (cont.)
• Employees in silos, hopers or tanks equipped with
  lifeline and safety harness
• Bound material stacked, on racks, blocked or
  interlocked to keep it from sliding, falling or
  collapsing
• Don't exceed load capacity for the structure
• Post load limits
• Stacking height
• Mark walls or posts to indicate maximum height

9
Lumber and Brick Storage

• Lumber
• Maximum stack height
• 16 feet (manual handling)
• 20 feet (forklift)
• Remove nails from used lumber
• Stacks stable and self-supporting
• Bricks
• Maximum 7 feet high
• Above 4 feet, taper stacks 2 inches per foot

Lumber storage
10
Block and Bag Storage

• Masonry blocks
• Above 6 feet , taper stacks 2 block per tier
• Bags and bundles
• Stack in interlocking rows
• Step back at least every 10 layers
• Remove from top of stack first
• Keep baled paper and rags at least 10 inches from
  walls, ceilings, or sprinkler heads

Block storage
11
Box and Drum Storage

• Boxed materials
• Hold in place using cross-ties, or shrink plastic
• Block cylindrical material (bars, poles, etc.)
• Use bins or shelves for materials that cannot be
  stacked

Box storage
12
Box and Drum Storage

• Drums, barrels, kegs
• Stack symmetrically
• If stored on side, block bottom tiers to prevent
  rolling
• If stacked on ends, use planks, pallets, etc.
  between each tier

Drum storage
13
Manual Lifting

• Manual lifting precautions
• Avoid manual lifting when possible
• Limit vertical lifting (knuckle-to-shoulder
  height)
• Be in good physical shape
• Plan the lifting operation
• Get a good grip
• Keep the load close to the body
• Do not twist or bend sideways
• Get help for large or heavy loads

Manual lifting
14
Manual Lifting

• Recommendations for specific tasks
• Grasp opposite corners on boxes, cartons sacks
• Use mechanical assistance for barrels and drums
• Wear leather gloves when handling sheet metal
• Plate glass
• Carry with bottom edge in gloved palm, other hand
  on top edge
• Never carry plate glass under the arm
• Use a team for long objects

Drum jack
15
2-wheeled hand trucks

• Safe hand truck use
• Tip load forward and slip tongue underneath
• Keep center of gravity low
• Let the truck carry the load - don't lean it too
  far
• Walk forward - keep load height low enough to see
• Secure bulky items to the truck
• Use specialty equipment
• Drums
• Appliances
• Stair climbers

Appliance truck
Hand truck
Stair-climbing truck
Drum truck
16
Conveyers

• Conveyer basics
• Hazards
• Nip points (rollers, near frame)
• Material may fall from conveyor
• Persons may be caught in the conveyor
• Controls
• Emergency stop button or pull cord
• Must be reset after use
• Never ride on conveyor
• Guards over aisles or
• work areas
• Screw conveyors covered, interlocked

Inclined belt conveyor
Screw conveyor
17
Powered Industrial Trucks (Forklifts)

• Forklift injuries and deaths
• 100 annual deaths, 95,000 injured
• Cause of fatality
• 42 crushed by vehicle tipping
• 25 crushed between vehicle and surface
• 11 crushed between two vehicles
• 10 struck or run over by vehicle
• 8 struck by falling material
• 4 fall from platform or forks
• 2 accidental activation of controls

18
Powered Industrial Trucks (Forklifts)

• Forklift injuries and deaths (cont)
• Classic forklift accidents
• Forklift overturns when traveling or lifting a
  load
• Trailer moves while being loaded or unloaded,
  causing the forklift to fall

19
Powered Industrial Trucks (Forklifts)

• Forklift safety
• ANSI Approved
• Identifying label
• Owner modification
• Only with mfg. Approval
• New label required
• Front-end attachments
• Should have new label

20
Classes of forklifts

• Electric Motor, Sit-down Rider, Counter-Balanced
  Trucks (solid and pneumatic tires)
• Electric Motor Narrow Aisle Trucks (solid tires)

21
Classes of forklifts

• Electric Motor Hand Trucks or Hand/Rider Trucks
  (solid tires)
• Internal Combustion Engine Trucks (solid tires)

22
Classes of forklifts

• Internal Combustion Engine Trucks (pneumatic
  tires)
• Electric and Internal Combustion Engine Tractors
  (solid and pneumatic tires)
• Rough Terrain Forklift Trucks (pneumatic tires)

Rough Terrain Extended-Reach Forklifts
Tractors
23
Trucks for Hazardous Locations

• Explosion proof forklifts are used to control
  ignition
• Example
• DS (Diesel), EE (completely enclosed electrical),
  or EX trucks where flammable gases or liquids are
  handled, but contained

24
Powered Industrial Truck Safety

• Fuel, liquid or gas
• Handled in accord with NFPA standards
• Batteries
• Hazards
• Lifting and handling
• Acid (electrolyte)
• Hydrogen produced during charging
• Precautions
• Designated battery charging area
• Spill control, fire protection, ventilation, etc.
• Mechanical handling equipment
• No smoking

Forklift battery
Battery charging station
25
Powered Industrial Truck Safety

• Trucks and Railroad cars
• Many deaths occur when a truck moves as it is
  loaded
• Forklift travel and braking action cause the
  truck to move away from the dock
• The forklift falls into the gap and the driver is
  crushed
• Precautions
• Brakes set, wheel chocks (trucks)
• Wheel stops (railroad cars)
• Trailer restraints secure the truck to the
  loading dock

Wheel chock
Trailer restraint
26
Powered Industrial Truck Operation

• Safe forklift operation
• Never drive toward a person standing in front of
  a fixed object
• No person under any elevated portion
• Do not place arms or legs in the mast or outside
  the truck
• Unattended trucks must be shut off with lowered
  load
• Set brakes and wheel blocks when loading vehicles
  (trucks, rail cars, etc.)
• Maintain headroom under lights, sprinkler
  systems, etc.
• Use overhead guard to protect from falling
  objects
• Use load backrest when necessary

27
Powered Industrial Truck Operation

• Safe forklift operation
• Cross railroad tacks on the diagonal
• Sound horn at blind intersections
• Back down ramps, drive forward up ramps
• Operate at safe speed, avoid quick turns
• Personnel on loading platform must have an
  emergency shut-off for truck power
• Secure dockboards and bridge plates
• Loads must be stable and safely arranged
• Disconnect battery before repairing electrical
  system
• Replacement parts must be equivalent to original

A dockboard is used to bridge the gap
between loading dock and truck/trailer
28
Forklift Training

• OSHA standard, 1919.178(l)
• Effective March 1, 1999
• Formal training program required
• OSHA specified topics
• Stability, operation, etc.
• Initial training before use
• Refresher training (based on observations)
• Employer must certify proper training

29
Forklift Training
Stability Triangle
Vehicle Center of Gravity (Unloaded)
B
A
Center of Gravity of Vehicle and Maximum
Load (Theoretical)
C
Notes
1. When the vehicle is loaded, the combined
center of gravity (CG) shifts toward line B-C.
Theoretically the maximum load will result in the
CG at the line B-C. In actual practice, the
combined CG should never be at line B-C. 2. The
addition of additional counterweight will cause
the truck CG to shift toward point A and result
in a truck that is less stable laterally.
30
Forklift Training
Stability Triangle
Load CG
Load CG
Vertical Stability Line (Line of Action)
Combined CG
Combined CG
Vertical Stability Line (Line of Action)
Truck CG
Truck CG
This vehicle is unstable and will continue to
tip over
The vehicle is stable
31
(No Transcript)