Accessory Description

1
Accessory Description
TPU Medical Grade Cooling Pad
Magnetic Lock
Ice Container Cap
Water Line Connector
9.6V DC Nickel-Hydrogen (Ni-H2) Battery Pack.
Top Cover
Buckle With Adjustable Belt
Timer Controller.
Buckle With Adjustable Belt
Backpack Ice Container.
Quickly Connector with Check Valve (Female side)
Quickly Connector with Check Valve (Male side)
Silicon Soft Tubing
2
How to setup for cooling pad and cooling system.
1.Place the cooling pad on the back as shown, and
place cooling system around the waist and
locked the buckle. 2.Connected the Quick-release
connector. 3.When everything is ready to use,
push and hold the Manual button to start the
circulation of cold water into the cooling
pad. 4.Once cooling pad is filled with cold
water. Choose desired timer button and press
the timing push button. (The timer controller
will run automatically according to selection.
Caution When using, please pull the tube
straight. If the tube are bent, the pump will be
damaged, and we will not take responsibility. Plea
se make sure that the water in the cooling
System runs smoothly. Do not use any sharp and
point objects to damage any elements.
3
Battery Charge

• DO NOT CHARGE BATTERY FOR OVER 6 HOURS.
• Plug the battery charge into the wall outlet.
• Unplug the battery plug from the systems timer
  controller.
• Connect the battery plug and change cable by
  snapping together
• the jack and the socket tightly.
• After charging for 5 hours, the battery pack will
  be warm.
• This condition is normal for
  fully-charged batteries.
• Pull apart battery plug and charge cable by
  pulling apart gently.
• If the speed of the pump slows down, it is time
  to recharge.
• After use, the battery pack will be warm! Wait
  until it cools before recharging.
• Recharging a warm, or hot battery pack will
  greatly shorten the batterys life.
• Unplug the charge from the electrical outlet if
  it is not going to be used for a long period of
  time.

Socket
Jack
Charger
9.6V Ni-H2 Battery Pack

• Caution
• BE SURE TO CHARGE BATTERY PACK BEFORE USING.
• IF BATTERY PACK IS NOT AFTER USE, COOL BEFORE
  RECHARGE.
• DO NOT RECHARGE BATTERY PACK THAT SHOWS LEAKAGE
  OR CORROSION, OR ATTEMPT TO OPEN BATTERY PACK.
• DO NOT DISPOSE OF BATTERY PACK IN FIRE.
• CHARGE USING NICKEL HYDROGEN BATTERY CHARGER.
• NICKEL-HYDROGEN RECHARGEABLE BATTERY.
• CAN BE AND MUST BE RECYCLED OR
  DISPOSED PROPERLY.

4
Fill in the water-1

• Switch the power switch off.
• Unplug the quick-release connector.
• Unplug the water line connector.
• Open the bags top cover and remove the ice
  container out.
• Open the cap. (Do not place cap on when freezing)
• Fill in clean water (ONLY) into the ice container
  until water level gets to the 1st water level
  line.
• Keep the ice container cap side facing upwards
  and store the ice container in the freezer.
  (Leave container open when freezing. Do not place
  container in freezer with cap on)

4.
3.
1.
2.
5.
6. Water
7. Cap side Facing up.
1st water level Line for freezing.
5
Fill in the water for circulation

• Once water is frozen, remove from freezer.
• For Water Circulation Add additional clean
  water up to 2nd water level indicator or about
  150 200 cc. (leave top 1/4 inch gap empty)
• Tighten the cap.
• Put ice container into the bag.
• Put the top caver back.
• Insert water line connector tightly into ice
  container cap sockets.
• Connected the quickly connector.

2.
1. Water
2nd water level Line, for water Circulation.
3.
5.
4.
6.
6
Timer Controller

• When everything is ready to use, push and hold
  the Manual button to start the circulation of the
  cold water into the cooling pad.
• Once cooling pad is filled with cold water.
  Choose desired timer button and press the timer
  push button. (The timer controller will run
  automatically according to selection.)

Timer Controller With Pump Unit.
Power Switch
Pump Unit
Power On
Manual Push Button
Manual
Power On Indicator
Every 1.5 Min. Runs 5 Sec.
Timer Push Button For Every 1.5 Min. Runs 5 Sec.
Every 1.5 Min. Runs 7 Sec.
Timer Push Button For Every 1.5 Min. Runs 7 Sec.
Every 1.5 Min. Runs 10 Sec.
Timer Push Button For Every 1.5 Min. Runs 10 Sec.
7
Global Parts Enterprise LLC. Limited Warranty
8
(No Transcript)