Cabinetmaking and Furniture Technology Safety Test Review

1
Cabinetmaking and Furniture Technology Safety
Test Review
2
General Safety Rules

• Under no circumstances should ___ be removed from
  machinery.
• guards

3

• When in doubt as to the proper operation of a
  machine or tool, ask the ___.
• instructor

4

• ___ ___ will be worn at all times.
• Safety glasses

5

• Students must not engage in ___ with a student
  who is operating a machine.
• conversation

6

• Long sleeved shirts should be rolled up above the
  ___.
• elbows

7

• Report any accident to the instructor ___ no
  matter how minor.
• immediately

8

• Machines will not be operated when the ___ is out
  of the shop.
• instructor

9
Table Saw

• The safety margin is ___ inches.
• 4

10

• Always keep the ___ down over the saw while the
  machine is in operation except when crosscutting
  or for special setups.
• guard

11

• Never allow the blade to project more than ___ of
  an inch above the stock to be cut.
• 1/4

12

• Remember when helping to tail off in the saw
  that the only purpose is to ___ the stock while
  the operator pushes it through the saw.
• support

13

• Stand to the ___ of the blade for most
  operations.
• left

14

• Never saw ___.
• freehand

15
Band Saw

• Set the saw guard and guide within ___ of an inch
  of the stock being cut.
• 1/4

16

• Do not ___ ___ of stock unless the blade is at a
  dead stop.
• back out

17

• Keep your fingers at least ___ inches from the
  moving blade.
• 2

18

• Do not stand at the ___ side of the saw when the
  blade is in motion.
• right

19
Jointer

• The safety margin is ___ inches.
• 4

20

• Keep the ___ closed at all times while the
  jointer is being operated.
• guard

21

• Never change the adjustment of the ___ table.
• outfeed

22

• The maximum depth of cut for edge jointing is ___
  of an inch.
• 1/8

23
Surfacer

• Never plane two boards ___ ___ ___. One board
  may be thinner than the other and it may result
  in kickback.
• side by side

24

• Do not change the ___ of the cut while the board
  is being fed through.
• depth

25

• Limit the depth of cut to ___ of an inch.
• 1/16

26

• Do not plane the ___ of a board in the planer.
• edge

27
Drill Press

• Withdraw the bit frequently when drilling deep
  holes to prevent ___ and freezing of the bit in
  the stock.
• burning

28

• Check to make certain that the ___ ___ and
  wrenches are all removed before starting the
  machine.
• chuck key

29

• Keep fingers at least ___ inches away from the
  rotating bit.
• 2

30

• Bore larger diameter holes at the ___ speed
  setting.
• slowest

31
Mortiser

• Set the table low enough so the ___ will not
  strike it at the bottom of the cutting stroke.
• chisel

32

• Keep your hands at least ___ inches away from the
  chisel while operating the machine.
• 4

33
Belt / Disc Sander

• Safety margin is ___ inches.
• 2

34

• Place the work on the ___ ___ side of the sanding
  disc.
• down stroke

35

• Check the abrasive for breaks and ___ and make
  sure that it securely fastened.
• tears

36

• Never hold ___ pieces by hand.
• small

37
Portable Power Tools (Router)

• Unplug the router before changing the ___ or
  making adjustments.
• bit

38

• Hold the router ___ when turning on the power to
  overcome the starting torque of the motor.
• firmly

39

• Always lay the router down with the bit pointing
  ___ from you.
• away

40

• Make sure that the bit is securely ___ before
  turning on the router.
• fastened

41
Miter Saw

• Keep fingers ___ inches away from the saw blade.
• 4

42

• Stock must be securely held on the table and
  against the ___.
• fence