Title: FAULT TOLERANCE TECHNIQUE USED IN SEAWOLF SUBMARINE
1FAULT TOLERANCE TECHNIQUE USED IN SEAWOLF
SUBMARINE
FAULT TOLERANCE TECHNIQUE EMPLOYED BY SEAWOLF
SUBMARINE
VIDYADHAR R EE 585 FAULT TOLERANT COMPUTING
2SEAWOLF SUBMARINE (SSN 21)
- Nuclear powered fast
- attacking submarine.
INSIDE VIEW OF SEAWOLF SUBMARINE
3SEAWOLF SUBMARINE
- State of the art Control system.
- Fault tolerant computer.
- Flat panel operator displays.
- Automatic modes of control.
- combat, gyrocompass inertial sensors and data
distribution system.
4 SEAWOLF SUBMARINE (CONT)
- Hardware PM software operate on failing of ship
control electronics, sensors and actuation
systems. - FL performed on maintenance computer for repair
and restoration of full redundancy. - PM software runs on 4 channel FTC, uses sensor
voting. - Runs real time diagnostic tests.
- PM transfers SCS functions to back-up systems.
5SEAWOLF SHIP CONTROL DESCRIPTION
- Interfaces with SCS sensors, actuators using A/D
signals processed by I/O modules. - Operator interfaced by flat panel displays in SCP
BCP. - Redundant MIL-STD-1553 data buses connect
displays with SCPU. - Interfaces with ship combat, data distribution
sys, gyro separate maintenance computer by
means of redundant serial data buses.
6SEAWOLF SHIP CONTROL DESCRIPTION (CONT)
- Bow planes position control actuation hardware
also interface with SCPU for control. - Redundant pressure sensors allow SCPU to serve as
master source of ships depth. - Controls rudder, stern plane steering diving,
drain pumps. - Interfaces with many valves and sensors for depth
and remote trim pump control.
7 PERFORMANCE MONITORING (PM) FUNCTIONS
- PM steering and diving support.
- PM depth control support.
- PM trim and Drain support.
- FTC OS detects reconfigures it when failure
occurs. - Detection automatic recovery for ship ctrl
failures. - Also detects mechanical and hydraulic failures.
- Allows sys repair without shutting down entire
system. - Real time notification status display to
indicate what part of ship control has failed. - Designed to detect 98 of all failures.
8FAULT LOCALIZATION (FL) FUNCTIONS
- Runs on separate maintenance computer when
requested by the crew to diagnose physical
location on failure. - Indicates which component has to replaced when it
is activated by the crew on occurrence of failure.
9PM/FL DEVELOPMENT PROCESS
- The Seawolf PM/FL development process followed
steps - System analysis and hardware specifications.
- Definition of the overall approach to PM/FL.
- Detailed specification and design of PM software.
- Full system simulated failure testing.
- Ship installation and sea trials experience.
101. System analysis and hardware specifications
- Analysis process Req.
- PM must compare expected sensed position of
surface and detect hydraulic failures. - Req. feedback sensors, sensed position of servo
valve, output I command signal from I/O
module to minimize upset. - Details of diving position control system and how
PM must interact with Emergency Control System.
112. Definition of the overall approach to PM/FL
- A mid-value selection filter was used for
masking, detecting and isolating failures of
redundant sensor inputs. - A state machine algorithm was chosen to detect,
isolate failures retractable bow planes. - Analog input PM applied to synchro sensors, and
measured voltages from ships speed log and tank
level sensors. - Discrete input was applied to valve position
limit switches and operator control switches
located on SCP.
123. Detailed specification Design of PM/FL
software
- Development process was an iterative one.
- The req. were tailored to follow an algorithm
which reduced run time and complexity the most. - Tests were conducted with software running on
actual target hardware, but interfaced with
simulated I/O signals.
134.Full system simulates failure testing
- With testing done, PM was integrated with actual
ship - control operating system.
- The ship control machinery and submarine were
simulated. - Over 1000 simulated failures were formally
tested. - The test discovered PM software problems and
several SCPU hardware deficiencies.
145.Ship installation sea trials experience
- As simulates testing of the system
- proceeded, the SCS was being
- installed on the SSN 21.
- PM correctly located faulty wired sensors and
installation and rigging problems with the ship
control machinery. - Tests of all rudder and diving planes worked
correctly during both dockside and at-sea tests. - Utility of PM surface prediction was also
demonstrated.
15BENEFITS OF PM/FL
- Enhances mission effectiveness of the submarine.
- Capable of reducing required crew members and
training. - Reduces required maintenance and operating costs.
- System can tolerate a second failure in the same
area and still retain full functional capability. - Out of stock, does not result in aborting a
mission, the system is robust enough for repair
at a later convenient time. - Automatic retest of system after Maintenance
computer accurately indicates which component
must be replaced to restore full system
redundancy. - PM automatically halts further operation of
machinery when it detects potential damage of
equipment due to incorrect operation of some
machine.
16FUTURE SUBMARINE PM/FL
- The following trends may shape the design of
future systems - Seawolf SCS is an evolutionary design towards
full fly-by-wire submarine control systems. This
leads to elevation of PM functions to higher
levels of criticality and making them integral to
the safety of the system. - Drive for fully automated completely fault
tolerant systems that can operate with minimal
crew involvement that require minimal sea
maintenance. - Applying fast developing technologies of Fuzzy
logic and Adaptive fuzzy logic for performing FL
in real time.
17ADVANCED CLASS OF SUBMARINES
18REFERENCES
- http//www.navsource.org/archives/08/080021.htm
- http//www.fas.org/man/dod-101/sys/ship/ssn-21.htm
- http//www.wikipedia.com
19QUERIES???