Title: Advanced Navigation
1Advanced Navigation
Sextant
2Objectives
1. Describe the parts of a marine sextant. 2.
Demonstrate how to read a sextant. 3. Describe
how to observe celestial bodies with a
sextant.
3Davis Quadrant circa 1775
4The parts of a sextant
- FRAME
- Made of strong material and is the structure on
which all other parts are mounted.
5The parts of a sextant
HANDLE Place to hold on to the sextant so as
not to interfere with the movements of other
parts.
6The parts of a sextant
- TELESCOPE Magnifies both objects being viewed.
Greatly increases accuracy and makes stars and
planets easier to see.
7The parts of a sextant
INDEX MIRROR Reflects the image of
the celestial body from the sky to the
horizon glass.
- LIMB Lower part of the frame, on which the arc
of degrees is inscribed.
ARC Altitude graduations of arc
inscribed on the limb.
8The parts of a sextant
- INDEX ARM Pivots at the top of the frame.
Mounted on the top is the index mirror. The
bottom of the arm has a pointer to indicate the
number of - degrees of separation between objects.
9The parts of a sextant
- HORIZON GLASS Permanently mounted circular
piece of glass about the size of a half dollar.
The left half of the glass is clear. The right
half of the glass is mirrored. When observing
a celestial body, the horizon is seen - through the left side, while
- the body is viewed on
- the right side in the mirror
- as reflected down from the
- index mirror.
10The parts of a sextant
- INDEX and HORIZON SHADES Similar to sunglasses,
these are used to reduce the intensity of bright
objects, such as the sun and the moon or the
glare of the the sun on the water.
11The parts of a sextant
- TANGENT SCREW Screw gear on the end of the
micrometer drum shaft. It engages - the teeth of the
- limb.
MICROMETER DRUM Allows readings to a minute of
arc
(between whole degrees on the arc).
12The parts of a sextant
- VERNIER Adjacent to the micrometer drum and
fixed to the index arm. Allows readings to a
tenth of a - minute of arc
-
-
RELEASE LEVERS By compressing the release
levers the tangent screw can be disengaged,
allowing movement of the index arm along
the arc.
13Reading a sextant
- Degrees are measured by noting the position of
the arrow on the index arm in relation to the
arc. Read the whole number of degrees - DO NOT
ROUND UP.
14Reading a sextant
- Minutes are measured on the micrometer drum by
noting the position of the 0 on the vernier (or
longer mark, signifying zero) in relation to the
graduations on the drum. Again, read the whole
number of minutes - DO NOT ROUND UP.
15Reading a sextant
- Tenths (or sometimes fifths) of a minute are
measured by noting which mark on the vernier
lines up with a mark on the micrometer drum -
CHOOSE THE BEST FIT.
16Reading a sextant
17Hs 29º 42.5
18Determining Error
- Before a sextant can be used to sight bodies, we
must find Index Error (IE). - Set the index arm and micrometer drum for 0º,
and observe the horizon.....
19(No Transcript)
20Determining Error
- If the image in the horizon glass and horizon
mirror are not a straight line, - Adjust the micrometer drum to achieve the
effect.....
21(No Transcript)
22Determining Error
- Read the IE off the micrometer.....
2320
5
0
1
40
What is the Index Error?
50
24IE 39.8
25Observing celestial bodies
- After IE is known, determine the bodies available
for observation from a starfinder or CAPN. - Record the Hc (altitude) and Zn (true bearing)
for at least five or six different first
magnitude stars. Like visual land navaids,
optimum spread in bearing is 60º.
26Observing celestial bodies
- For the first star, set the sextant to the
altitude and look on the true bearing (using your
gyrocompass). - Once the star is sighted, adjust the micrometer
drum (or release levers, if necessary) to bring
the star into view.
27Observing celestial bodies
- With the star in view, adjust the micrometer
drum in order to bring the body down to the
horizon and fine tune your sighted altitude
(Hs) reading.
28Questions?
29Compliments of Curtis Senior High School NJROTC