Link Belt 175 AT Crane Service Manual

1
Service Manua?
SMOOOOOOOO.OO
0519
How To Use This Manua?? Genera? Service
?nstructions? And Safety Procedures The fo??owing
information is provided to he?p guide the user of
this manua?. An exp?anation of how this manua? is
organized? as we?? as genera? information and
safety considerations which shou?d be
understood when performing any service or
maintenance procedure? is given. This information
is genera? in nature and shou?d supp?ement any of
the specific procedures in this manua? a?ong with
a constant awareness of safety and common
sense. How To Use This Manua? This Service
Manua? is a co??ection of written procedures
which are used to service and maintain a specific
crane mode?. The index? which is ca??ed
a ?Keysheet?? is used to organize the procedures
within this manua? and serve as a Tab?e Of
Contents as we??. Each procedure? in this manua??
is written so that it can stand a?one and
typica??y covers on?y one procedure. Procedures
are given a numerica? designation? or ?SM Code?
Number? (Examp?e SM01005034.00) which is
unique to that procedure and that procedure on?y.
The fo??owing is a ?isting of the genera? area
definitions which are designated by the first
digits in the SM Code Number sequence Genera?
Area Descriptions SM01 Rubber Tire Lower SM02
Craw?er Lower SM03 Upper Revo?ving Frame ?
Machinery SM04 Vertica? Shafts SM05
Horizonta? Shafts SM06 Upper Engine SM07
Hydrau?ic Power Supp?y SM08 Ang?e Boom SM09
Tubu?ar Boom SM10 Tag?ine Winder SM11
Fair?eader SM12 Shove? Attachment SM13 Trench
Hoe? Logger ? Scrapper Attachment ? Prop
Hand?er SM14 Cab ? House Assemb?y SM15
Rotascope Attachment (Discontinued) SM16 Wire
Rope Requirements SM17 Hydrau?ic Boom And
Attachments SM18 Specia? Attachments SM19
Diese? Pi?e Hammer (Discontinued) SM20 Tower?
C?imbing Assemb?y? Trave?ing Base ? Gantry
(Discontinued) SM21 Log Skidder
(Discontinued) SM22 Hydrau?ic Hammer
(Discontinued) The procedures in this manua? are
co??ated by SM Code Number sequence. Use the
Keysheet in the front of this manua?? the genera?
area descriptions shown previous?y? and the SM
Code tit?e shown on the
Keysheet to find the specific procedure required
to service the crane. Throughout this manua??
reference is made to the ?eft? right? front? and
rear? pertaining to directions and ?ocations.
These reference directions are re?ative to
the operator? sitting in the operator?s seat?
with the upper direct?y over the front of the
carrier? un?ess otherwise stated. (Craw?er
mounted cranes upper over the front of the crane
with trave? motors to the rear.) Danger? warning?
and caution captions as we?? as specia? notes are
used throughout this manua? and on the crane to
emphasize important and critica? instructions.
?f any instruction? caution? warning? or danger
?abe?s? deca?s? or p?ates become ?ost? damaged?
or unreadab?e? they must be rep?aced. Information
contained on such ?abe?s? deca?s? and p?ates is
important and fai?ure to fo??ow the information
they contain cou?d resu?t in an accident.
Rep?acement ?abe?s? deca?s? and p?ates can be
ordered through a danger? warning? and caution
captions and notes are defined as fo??ows
DANGER
An operating procedure? practice? etc. which? if not correct?y fo??owed? may resu?t in severe persona? injury? dismemberment? or ?oss of ?ife.

WARN?NG
An operating procedure? practice? etc. which? if not correct?y fo??owed? may resu?t in persona? injury.

CAUT?ON
An operating procedure? practice? etc. which? if not correct?y fo??owed? may resu?t in damage to? or destruction of? equipment or property.
NOTES Note An operating procedure step?
condition? etc. which is essentia? in order for
the process to be comp?eted proper?y.
This symbo? may appear in manua?s or on a ?abe?
on the crane to a?ert personne? that
additiona? instructions are inc?uded in the crane
Operator?s Manua?. 1 of 6
2
SMOOOOOOOO.OO
Service Manual
0519
DANGER
Keep clear of moving parts to prevent serious
bodily injury.
Figure 1 Keep hands and tools clear of moving
parts.
Figure 3 Pinch Point Label
Diesel exhaust fumes can be harmful. Start and
operate engine in a well ventilated area. If it
is necessary to operate in an enclosed area, vent
the exhaust to the outside. Properly maintain
the exhaust system to its original design.

• First aid supplies and a fire extinguisher should
  be on the job site to assist in an unexpected
  situation. The location of these items should be
  known to all as well as access to a telephone
  for emergencies.
• Work in a clean,
• sible. Choosing the correct work site can make a
  big difference on how well the job goes.

Figure 2 Diesel Exhaust Fumes.
5. Use caution around flammable materials. Be
aware of all the materials in the work area which
are
Service Safety And Set Up Guidelines The
following is a list of safety and set up
als post signs if necessary. 6. Release all
trapped pressure in air and hydraulic
nent. Shutdown the crane, exhaust all pressure
considerations which may apply to any service or
maintenance procedure. Review the entire list
and understand the type of things you must
consider to perform a safe service procedure and
then apply these guidelines to each specific
service or maintenance procedure.
draulic control levers back ing the crane. 7. Do
not disconnect any hydraulic line from a crane
ing a line could release the trapped pressure,
DANGER

• ment to the ground or on to its rest before
  servicing the crane.
• Do not work on a crane which is in motion. Fans,
  belts, gear trains, etc. can catch an
  unexpecting
• person and quickly dismember them.
• Do not climb on the attachment or other hard to
  reach areas. If the steps and/or ladders which
  are

Do not operate the crane unless you are
qualified. Unauthorized operation by
untrained personnel could result in an
accident. Crane operation is to be performed by a
certified operator only.

• Service Safety
• Read and understand the service or maintenance
  procedure to be performed before beginning work.
• By reading the procedure ahead of time, you can
  be sure to have the replacement parts and tools
  on hand that are required to complete the job.
• Wear protective gear to prevent injury hard hat,
  safety glasses, gloves, steel toed shoes, etc.

ing, use a step ladder or other approved
device. 10. Pinch points exists between the upper
and lower frames. Death or dismemberment may
result from personnel caught in these points.
Learn where these pinch points are and stay clear
of the rotating upper frame.
2 of 6
3
Service Manual
SMOOOOOOOO.OO
0519
Right
Figure 5 Allow engine to cool before removing
the radiator cap.
Figure 4 Use a guard when inflating tires.

• If the crane is equipped with outriggers, it may
  be safer as well as an advantage to raise and
  level the crane on outriggers to provide easier
  access to areas underneath. Do not work under a
  crane that is improperly supported.
• Shutdown the engine(s) per the instructions given
  in the Operators Manual.
• Post a sign in the operators cab to alert others
  that the crane is being serviced.
• Engines, transmissions, hydraulic systems, etc.
• atures can reach levels which may cause serious
  burns. Allow the crane to cool before attempting
  to service it.

• equate ventilation when
• ing toxic solvents, welding, or any other
  operation which contaminates the fresh air
  supply.
• Post a sign in the operators cab to alert others
  that the crane is under service. Starting the
  crane while it is being serviced could severely
  injure someone.
• erated prematurely. Imagine starting the
  engine(s) before the oil is replaced.
• Secure access panels, doors, and machinery
  hoods when in the open position to ensure they
  do
• ruption. propriate lifting
• tempt to lift an object without knowing its
  weight.
• Get help if necessary.
• flating tires. W
• plode from the assembly causing serious injury.
  Use a safety rim cage, clip on air chuck, and
  stand aside when inflating or deflating tires.
• Crane Set Up And Disassembly
• Properly
• tors Manual. Park
• vides the most comfortable working conditions.
  However, do not park the crane where it will be
  an obstruction or an intrusion to traffic,
  coworkers, or to the public. Keep in mind that a
  major service procedure, or a repair part which
  requires a long lead time,
• tended period of time.
• Keep in mind the mess which is sometimes caused
  by a crane under repair. Oil or other fluid
  leaks should be contained or prevented. Consider
  your
• responsibility of maintaining a safe clean work
  area and a healthy environment for all.

WARNING
Engine coolant is hot. Failure to allow
engine(s) to sufficiently cool before draining
coolant could result in severe burns or other
personal injury. Allow the engine(s) and
radiator(s) to cool before draining coolant from
the radiator(s).
7. Pressure is generated inside the engines
cooling system due to the heat transfer process
from the engine(s) to the radiator(s). Do not
attempt to open or drain the radiator(s) until
it/they has/have had sufficient time to cool.
Disconnecting hoses before the engine(s) and
radiator(s) has/have cooled is even more
dangerous. Wait gine(s) and radiator(s) have
cooled and then drain the radiator(s) before
disconnecting any hoses. Properly store or
dispose of used coolant.
3 of 6
4
SMOOOOOOOO.OO
Service Manual
0519

• Hydraulic systems, while operating, are under
  high pressure. Even after the crane is shutdown
  these pressures can remain trapped in the
  hydraulic lines and system components. Some
  hydraulic systems utilize an air pressurized
  reservoir which maintains pressure on the system
  after the crane is shutdown. It is critical
  that all residual pressure,
• nent. Use the following techniques to exhaust
  trapped hydraulic pressure from the system
• Lower the attachment to the boom rest, onto
• blocking, or onto the ground and shutdown the
  engine(s).
• voir(s), if equipped, to bleed the air system
  pressure.
• Relieve any residual or precharge pressure by
  pushing the button on the pressure relief valve,
• wise, loosen the filler cap 1/4 turn.
• Turn the ignition switch to the ON POSITION, but
  DO NOT START THE ENGINE.
• Operate the steering control(s) back and forth
  repeatedly until steering becomes hard. (On
• cranes equipped with emergency steering
• system, it will take several rotations of
  steering wheel before steering becomes hard.)
• Work the crane control levers and outrigger
• switches, if equipped, back and forth several
  times.
• Turn ignition switch to the OFF POSITION.
• When pressure is fully relieved, close the drain
  valves on the air system reservoir(s), if

Wrong
Figure 6 Do not use an open flame near the
battery.
WARNING
Solvents and cleaning solutions can be
hazardous. Serious personal injury may
result from misuse of these products. Read and
follow all the manufacturer?s
recommendations concerning solvents and cleaning
solutions.

• Thoroughly clean the area of the crane which is
  to
• ter the hydraulic, air, lubricating system, etc.
  and cause immediate and/or long term problems.
• tamination problems but it also makes working on
  the crane easier and sometimes problems are more
  recognizable.
• Before
• cedure, take a moment to observe critical
  features
• of the assembly which may greatly simplify the
  installation or assembly process. Label
  electrical, hydraulic, air, or other connections.
  Index mark pump, motor, and valve sections.
  Lightly spray paint or count the threads of
  adjustment screws. Simple steps such as these can
  minimize the effort needed to put the crane back
  in service.

WARNING
Air lines may contain high pressure. Opening
lines and fittings before relieving air pressure
may result in serious injury. Shutdown the
engine(s) and drain the air system
reservoir(s) before opening any line or fitting.
WARNING
11. Air system circuits, like hydraulic circuits,
contain high pressures also. Although the threat
of a hot working fluid does not exist, highly
pressurized lines and components can possibly
?fly off if lines are disconnected bef lieved.
Hydraulic oil is under pressure and may be hot. A
sudden release of hot oil could cause severe
burns and/or other serious injury. Shutdown
the engine(s) and exhaust all trapped
hydraulic pressure from the system before
removing any line or component.
ing on the crane.
4 of 6
5
THIS IS A SAMPLE MANUAL
FOR THE COMPLETE MANUAL
CLICK HERE TO DOWNLOAD
6
Service Manual
SMOOOOOOOO.OO
0519

• Do not position the ground connection where seals
  or bearing, as in transmissions or valves, will
  be between it and the welded parts.
• Remove any flammable materials from the area.
• Use the appropriate setting on the welder for the
  size of the welding operation. Do not use more
  than 200 Volts continuously.
• Cleaning And Inspection

WARNING

• Use care not to cause sparks at the battery
  terminals while disconnecting or connecting the
  battery. Battery gasses are volatile and could
  be ignited by a spark or flame causing the
  battery to explode. Keep the area around the
  battery well ventilated and disconnect the
  negative side of the battery first, with the
  ignition switch ?OFF?, to minimize hazard.
• Battery posts, terminals, and accessories contain
  lead and compounds. Eating or smoking with lead
  residue on hands may cause lead poisoning. Wash
  hands after handling lead products.
• When working on electrical circuits, disconnect
  the battery to minimize shock, burn, spark, or
  other hazard. When disconnecting the battery,
  confirm
• connect the negative side of the battery first to
  minimize the potential for sparks at the battery.
  Battery gases which are exposed to such sparks,
• necting the battery, confirm that the ignition
  switch is in the OFF position and install the
  positive cable(s), first and the negative
  connection(s) last.
• It is a good practice when disassembling
  hydraulic components to lay the parts out in the
  order that they were disassembled. Keeping the
  parts in this
• tion will aid in the assembly process.
• Welding
• connect any electronic equipment (such as rated
  capacity limiters and engine computers) to
  prevent damage to them. Use the battery
  disconnect switch(es), if equipped.
• Be aware of systems adjacent to areas being
  welded. Residual heat from the welding process
  could cause damage to other components. Heat
  may also vaporize materials which may become
  toxic or volatile.
• Remove paint from areas to be welded to prevent
  toxic fumes.
• The grounding connection should be within 3 feet
  (1 m) of the welded parts.
• Connect the ground to the lower, if welding on
  the lower, or to
• trical current through the turntable bearing
  could

WARNING
Solvents and cleaning solutions can be
hazardous. Serious personal injury may
result from misuse of these products. Read and
follow all the manufacturer?s
recommendations concerning solvents and cleaning
solutions.
related lead

• All components should be thoroughly cleaned with
• fully inspected for damage, wear and corrosion.
• All Loctite
• moved from threads of hardware and parts that are
  going to be reused.
• All soft parts, such as seals, gaskets, back up
• Replacement of
• ly a good preventive maintenance measure. Even
  though a bearing or bushing seems to be intact
  and is functioning properly, its life span is
  limited. Replacing a simple bearing or bushing
  while the opportunity is at
• ponent failure later.
• sonnel for directions whether to repair or
  replace any major component.
• Crane Assembly
• Loosely assemble parts to ensure all parts are in
  place and fasteners started before beginning
  torquing procedure. Always use a cross torquing
  sequence to ensure even and uniform installation.

WARNING
Lubricants, sealants, joint and thread locking
compounds, etc. can be hazardous. Serious
personal injury may result from misuse of these
products. Read and follow all manufacturer?s
recommendations concerning these products.
5 of 6
7
SMOOOOOOOO.OO
Service Manual
0519

• Unless otherwise stated, torque all fasteners per
  the instructions given in SM Code Area 18000.
• When installing hydraulic hoses, lines, and
  fittings, use two wrenches to ensure the hoses
  and lines
• are not twisted. One wrench must be on the male
  fitting, the other wrench on the female fitting.
• Unless otherwise stated, torque all hydraulic
  fittings per the instructions given in SM Code
  Area 07018.
• Check all fluid levels before returning the crane
  to
• service hydraulic reservoir oil level,
  transmission

Wrong
quired. See Operators Manual and/or engine(s)
manufacturers manual(s) for correct type of
fluids and procedures. 6. Always replace guards,
grilles, and other types of protective shields.
Also, be sure that any systems which were
disconnected such as load indicating
etc. are functioning properly before returning
the crane to service. 7. Start the appropriate
engine and let it idle for five minutes. Inspect
the connections on the hydraulic, air,
transmission, etc. lines for leaks. Repair if
needed.
Figure 7 Proper disposal is important.
tions are operating normally before returning the
crane to service. 9. After crane is assembled,
refer to the Operators Manual for any periodic
type of adjustments which may have been affected
by the service procedure. ers, etc.
6 of 6
8
Service Manua?
SM01001017.00
1220

• Boom Rest? R ? ?
• This procedure covers the remova? and
  insta??ation of the boom rest top section. It is
  not advised to remove the entire boom rest
  assemb?y. If comp?ete boom rest assemb?y
  rep?acement is required? p?ease contact your
  distributor.
• Remova?
• Lower? detach? and secure ?oad? as required.
• Stabi?ize crane for service as fo??ows
• Park crane out of way on a firm and ?eve?
  surface.
• App?y park brake? and/or proper?y b?ock tires.
• Leve? crane on fu??y extended outriggers.
• Shutdown carrier engine.
• Start upper engine? and app?y swing park brake
  or engage trave? swing ?ock? as required.
• Fu??y retract and position boom? as required.
• Shutdown engine(s). Refer to Operator?s Manua?
  for correct procedure. A??ow engine(s) and
  hydrau?ic oi? to coo?.

• mate?y 110 ?b (50kg).
• Support boom rest top section (3) but do not ?ift
  at this time.
• Remove capscrews and washers (6) and remove boom
  rest top section (3) from crane.
• If necessary remove wear b?ock (7) by removing
  capscrews? washers? and ?ocknuts (8).
• C?eaning And ?nspection

WARN?NG
So?vents and c?eaning so?utions can be hazardous.
Serious persona? injury may resu?t from misuse
of these products. Read and fo??ow a?? the
manufacturer?s recommendations concerning
so?vents and c?eaning so?utions.

1. A?? components shou?d be thorough?y c?eaned with
   an approved c?eaning so?vent? air dried? and
   carefu??y inspected.
2. A?? Loctite?? Permatex?? or other sea?ant
   residue shou?d be removed from threads of
   hardware and mounting surfaces of parts to be
   reused. Prior to app?ying new thread ?ocking
   compounds or sea?ants? c?ean threads and
   surfaces with Loctite? 7070 C?eaner to ensure
   best performance of products.
3. Thorough?y inspect a?? parts for damage? wear?
   fatigue or stress fractures? and corrosion.
   Repair or rep?ace? as required.
4. Ensure integrity of e?ectrica? wires and
   connectors connected to boom rest structure.
   Repair or rep?ace? as required.
5. In the event of severe defects? contact factory
   personne? for directions whether to repair or
   rep?ace any major component.

WARN?NG
So?vents and c?eaning so?utions can be hazardous.
Serious persona? injury may resu?t from misuse
of these products. Read and fo??ow a?? the
manufacturer?s recommendations concerning
so?vents and c?eaning so?utions.
4. Thorough?y c?ean area to be disassemb?ed with
an
approved c?eaning so?vent to prevent

• contamination. A??ow area to air dry.
• Refer to Figure 1.
• Remove capscrews and washers (1) and cover
  p?ates (2).
• Remove capscrews and washers (5) and pads (4).

1 of 4
9
SM01001017.00
Service ManuaI
1220
1
2

1. Capscrew ? Washer
2. Cover P?ates
3. Boom Rest Top Section

1. Pad
2. Capscrew ? Washer
3. Capscrew ? Washer

1. Wear B?ock
2. Capscrew? Washer? Locknut

Figure 1 Boom Rest AssembIy 2 of 4
10
Service ManuaI
SM01001017.00
1220
3
4
5
6
7
8
6
3 of 4
11
SM01001017.00
Service ManuaI
1220
?nstaIIation WARN?NG

• mateIy 110 Ib (50kg).
• Using an appropriate ?ifting device? proper?y
  position boom rest top section (3).
• App?y Loctite? 243 to threads and insta??
  capscrews and ?ocknuts (6). Torque capscrews (6)
  to 435480 ft ?b (590651Nm).
• Proper?y position pads (4).
• App?y Loctite? 243 to threads and insta??
  capscrews and washers (5).
• Insta?? cover p?ates (2) using capscrews and
  washers (1).
• Comp?ete insta??ation by testing a?? re?ated
  functions of boom rest for proper operation.

Lubricants? seaIants? joint and thread Iocking
compounds? etc. can be hazardous. Serious
personaI injury may resuIt from misuse of these
products. Read and foIIow aII manufacturer?s
recommendations concerning these products.

• Refer to Figure 1.
• If removed? position wear b?ock (7) in boom rest
  top section (3).
• App?y Loctite? 243 to threads and insta??
  capscrews? washers? and ?ocknuts (8).

4 of 4
12
SM01 002 - 028.00 0417 1 Drive/Steer Shaft Axle
Assy, Recondition Service information not
available at time of publication. Updated
information to follow with later revision.
Service Manual
2 of 2
13

14

15
THIS IS A SAMPLE MANUAL
FOR THE COMPLETE MANUAL
CLICK HERE TO DOWNLOAD