John Deere 1155 Combines Service Repair Manual Instant Download

1
1123, 1144, 1155,
1157 and 1158
Combines
John Deere Werke Zweibrücken
TM4476 Printed In Germany (Engliah)
2
SUMMARY OF MOST IMPORTAKT SPECIFICATIONS 1133,
1144, 1155, 1157, 1158
SUMMARY OF MOST IMPORTANT SPECIFICATIONS 1122,
1144, 1155, 1157, 1158
SPECIFICAfIONS
SPECIFICATIONS (Continued)
4239, 6359 Engines
Steering System
0.35 mm (0.014 in.) 0.45 mm (0.018 in.) 2100 kPa
(21 bar 300 psi)
Valve clearance, intake valye Valve clearance,
exhaust yalye
Pressure relief valve setting ...
10500 kPa (105 bar t520 psi)
Safety valve setting .
15000 to 16500 kPa (150 to 165 bar 2175 to 2390
psi)
Compression .
Clutch
Max. di0erence in compression pressure between
cylinders
350 kPa (3.5 bar 50 psi)
7 mm (0.28 in.)
Minimum thickness of clutch disk
25100 to 25800 kPa (251 to 258 bar 3650 to 3750
psi)
Wheels
Opening pressure of a new injection nozzle

• Wheel bolt torques
• Front wheels
• Rear wheels

Minimum opening pressure of a used nozzle
24100 kPa (241 bar 3500 psi)
420 Nm (304 R-lb) 180 Nm (130 R-lb)
Maximum diXerence in opening pressure
700 kPa (7 bar 100 psi)
CAPACITIES
Fast idle .........
2675 50 rpm
1200 50 rpm

• Engine lubrication system
• 1133, 1J44, 1155
• 1157 . ........ ........ ..... .............
• 1158 . ... ........ ...... .......
• Transmission with differential
• 1133, 1144
• - 1155, 1157, 1158

8.5 liters (2.25 U.S.gal.) 11.5 liters (3.05
U.S.gizI.) 13 liters (3.4 U.S.gal.)
Air Intake System
Air cleaner restriction indicator light will glow
at a vacuum of
500 mm (20 in.) waterhead
12 liters (3.25 U.S.gal.) 6.6 liters 1.75
U.S.gal.)
Cooling System
Thermostat opening temperature
71 to 82C (160 to 180DF)
Final drive (each), 1155, 1157, 1158
2.1 liters (0.55 U.S.gal.)
Electrical System
Complete hydraulic system 1133, 1144, 1155
1157, 1158
15 liters (4.0 U.S.gal ) 25 liters (6.6 U.S.gal.)
Battery voltage
12 yolts
Alternator output current (at 14 volts) 1133,
1144 ... - 1155, 1157, 1158
Engine cooling system - 1133, 1144, 1155 JJ57,
1158
55 amps 95 amps
22 liters (5.8 U.S.gal.) 25 liters (6.6 U.S.gal.)
Hydraulic System
Refrigerant capacity (air conditioning)
1950 g (68.8 oz.)
Hydraulic pump delivery 1133, 1144 - 1155,
1157, 1158
Compressor oil charge .
320 cm3 (19.5 cu.in.)
32.4 liters/min (8.5 gpm) 38.4 liters/min (10 gpm)
Fuel tank capacity 1133. 1144 J155, 1157, 1158
110 liters (29 U.S.gal.) 175 liters (46 U.S.gal.)
Pressure relief va/ve setting .
13800 to 14500 kPa (138 to 145 bar 2000 to 2100
psi)
SPECS-Zl8llAE-t 11189
SPECK-ZIBJAE-11J 1B9
JDWZ Combines
TM-4476 (Jan-90)K9 Printed in Germany
JDWZ Combines
TM-4476 (Jan-90)K9 Printed in Germany
3
Combines 1133, 1144, 1155, 1157 and
1158 TECHNICAL MANUAL TM-4476 (JAN-90) CONTENTS
OF SECTIONS SECTION 60 - BRAKES, REAR AXLE AND
STEERING REPAIR Group 05 Parking brake (3-speed
transmission) Group 10 Parking brake (4-speed
transmission) Group 15 Brake operation
SECTION 10 - GENERAL Group 05
Specifications SECTION 20 ENGINE REPAIR
Group 05 Removal and installation, 4-cyI.
engine Group 10 Removal and installation,
6-cyI. engine SECTION 30 - FUEL AND AIR
REPAIR Group 05 Fuel filter with water trap and
electrical fuel transfer pump SECTION 40 -
ELECTRICAL SYSTEM REPAIR Group 05
Connectors Group 10 - Electrical system
components Group 15 Starting motor Group 20
Alternator Group 25 Low shaft speed monitor
system Group 30 Electromagnetic transmission
brake SECTION 50 - POWER TRAIN REPAIR Group 05
Variable ground speed drive Group 10 Engine
clutch and mechanical clutch operation (3-speed
transmission) Group 15 Engine clutch
operation (4-speed transmission) Group 20
Engine clutch (4-speed transmission) Group 25
Three-speed transmission Group 30 Four-speed
transmission with differential Group 35 Final
drives, differential (3-speed transmission) Group
40 Final drives (4-speed transmission) Group 45
Final drive on rice combine (4-speed
transmission)
Group 20 Foot brakes (3-speed transmission)
Group 25 Foot brakes (4-speed transmission)
Group 30 Foot brakes with integrated slave
cylinder Group 35 Hydrostatic steering unit
Group 40 Rear axle Group 45 V-support for
wide rear axle Group 50 Steering
cylinder SECTION 70 - HYDRAULIC SYSTEM
REPAIR Group 05 Hydraulic oil reservoir and
lines Group 10 Hydraulic pump Group 15
4-spool control valve with flow divider Group 20
Hydraulic cylinders Group 25 Hydraulic system
diaphragm-type accumulator
SECTION 80 - MISCELLANEOUS Group 05 Bearings
and shafts Group 10 Drive belts Group 15
Drive chains SECTION 90 - OPERATOR'S PLATFORM
WITH CAB Group 05 Safe handling of refrigerants
Group 10 Air conditioning compressor Group 15
Air conditioning system components Group 20 Air
conditioning system service and tests Group 25
Cab ventilation system Group 30 Cab heating
system Group 35 Operator's cab Group 40
Control levers Group 45 Operator's seat SECTION
100 - CUTTING PLATFORM AND CORN HEAD
COPYRIGHTC 1990 DEERE 8 COMPANY European Office
Mannheim AII rights reserved A John Deere
ILLUSTRUCTION! Manual
INHA-ZI81AE-111189
1
TM-4476 (Jan-90)K9 Printed in Germany
JDWZ Combines
4
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com
5
CONTENTS OF SECTIONS - CONTD. SECTION 230 - FUEL
AND AIR INTAKE SYSTEM OPERATION
SECTION 110 - FEEDER HOUSE
Group 05 Feeder house drive
Group 10 Feeder house with compact cutting
Group 05 General information, fuel filter and
fuel transfer pump SECTION 240 - ELECTRICAL
SYSTEM - OPERATION AND TESTS Group 05 - General
information Group 10 Circuit plan, wiring
diagram and wiring harnesses Group 15 Checking
indicator lights Group 20 Checking low shaft
speed monitor system Group 25 Checking straw
warning device Group 30 Checking
electromagnetic trans- mission brake SECTION 250
- POWER TRAIN - OPERATION AND TESTS Group 05 -
Engine clutch and operation (3-speed) Group 10
Engine clutch and operation (4-speed) Group 15
Three-speed transmission Group 20 Four-speed
transmission SECTION 260 - BRAKES, REAR AXLE AND
STEERING - OPERATION AND TESTS Group 05 Brake
operation Group 06 Foot brake and brake
operation (combines with rice equipment) Group 10
- Operation and flow diagram - hydrostatic
steering Group 15 - Diagnosing steering system
malfunctions Group 20 - Primary (steering)
circuit testing SECTION 270 - HYDRAULIC SYSTEM -
OPERATION AND TESTS Group 05 Hydraulic circuit
symbols Group 10 Hydraulic lift circuit Group
15 Lifting system - diagnosing mal-
functions Group 20 Hydraulic lift circuit
testing
platform Group 15 Feeder house with quick-tach
cutting platform SECTION 120 - SEPARATOR AND
CLEANING UNIT Group 05 Stone trap Group 10 -
Separator drive Group 15 Variable cylinder
drive Group 20 Threshing cylinder Group 25 -
Concave Group 30 - Beater variable drive Group 35
Beater Group 40 - Cross shaker Group 45 - Straw
walkers Group 50 - Cleaning shoe, grain return
pan and auger housing Group 55 - Fan and variable
speed drive SECTION 130 - GRAIN PROCESSING Group
05 Clean grain and tailings augers Group 10 -
Clean grain elevator Groyp 15 Tailings elevator
Group 20 - Upper tailings auger Group 25 - Grain
tank leveling auger Group 30 - Grain tank center
fill auger Group 35 - Inner grain tank unloading
auger Group 40 - Outer grain tank unloading
auger Group 45 Discharge tube SECTION 140 -
SPECIAL EQUIPMENT Group 05 - Straw chopper
drive Group 10 - Straw chopper rotor
bearings SECTION 220 - ENGINE OPERATION
INHA-ZI82AE-J 11189
TM-4476 (Jan-90)K9 Printed in Germany
JDWZ Combines
6
CONTD.
CONTENTS OF SECTIONS - SECTION 290 - OPERATOR'S
PLATFORM AND CAB - OPERATION AND TESTS Group 05
Cab ventilation system Group 10 - Air
conditioning system Group 15 - Safe handling of
refrigerants Group 20 Testing air conditioning
system Group 25 - Cab heating system
tNHA-Zt83 E-111I g9
TM-4476 (Jan-90)K9 Printed in Germany
JDWZ Combines
7
GENERAL
Section 10
CONTENTS OF THIS SECTION QROUP 05 -
SPECIFICATIONS Metric and inch threads ........
10-05-1 Standard torqueG ........................
10-05-2
10-1
TM-4476 (Jan-90) K9 Printed in Germany
JDWZ Combines
8
Group 05 SPECIFICATIONS A B
METRIC AND INCH THREADS
M 6
The adjacent chart compares the diameters of
metric and inch threads.
1/4
5/16 -
M 8
3/8
M 10
A-Inch thread B-Metric thread
7/ 16
M 12
1/2
M 14
9/16
5/8
3/4
M 20
7/8
M 24
1
M 30
M36
z oaeso
Z103950-ZI21005AE-011084
10-05-1
TM-4476 (Jan-90)K9 Printed in Germany
JDWZ Combines
9
Specifications
STANDARD TORQUES - GENERAL All specified torques
are only valid for non-greased or non-oiled
threads. A variation of 100/o is permissible
for all torques speci- fied below. TECH-ZI2100
5AE-011084
RECOMMENDED TORQUES FOR UNC AND UNF CAP SCREWS
10.9 10.9 2.9 2.9
Nm ft-lb Ncn ft-lb
1/4 5/16 3/8 7I\6 1/2 9/16 5/8 3/4 7/8 1 1-1/8 1-1/4 15 30 50 80 120 180 230 400 600 910 1240 1700 10 20 35 55 85 130 170 300 445 670 910 1250 20 40 70 110 170 240 320 580 930 1400 1980 2800 15 30 50 80 120 175 240 425 685 1030 1460 2060
'1O3B47
A-Thread O.D. (in.) B-Head marking (identifying
strength)
10.0 - Tempered steel high strength cap screws
12.9 - Tempered steel extra high strength cap
screws
Z103947-Zl24 OOSAE01 4084
10-05-2
JDWZ Combines
TM-4476 (Jan-90) K9 Printed in Germany
10
Specifications RECOMMENDED TORQUES FOR METRIC
CAP SCREWS
8.8 8.8 10.9 10.9 12.9 12.9
Nm ft-lb Nm ft -Ib Nm ft -Ib
M5 7 5 9 6,5 10 8,5
M 6 10 8,5 15 10 20 15
M 8 30 20 40 30 40 30
M 10 50 35 80 60 90 70
M 12 100 75 140 100 160 120
M 14 160 120 210 155 260 190
M 16 ?40 175 350 260 400 300
M 20 480 355 650 480 780 575
M 24 820 605 1150 850 1350 995
M 30 1640 1210 2250 1660 2700 1990
M 36 2850 2110 4000 2950 4700 3465
Z 104 148
8.-Regular cap screws 10.9-Tempered steel high
strength cap screws
12.9-Tempered steel extra high strength cap screws
A-Head marklng (Identifying strength) B-Thread
O.D. (mm)
Z103948-ZI21005AE-011084
RECOMMENDED TORQUES FOR PIPE AND HOSE CONNECTIONS
A B B C C
A Nm ft-Ib Nm ft-lb
3/8-24 UNF 7/16-20 UNF 1/2-20 UNF 9/16-18 UNF 3/4-16 UNF 7/8-14 UNF 1-1/16-12 UNC 1-3/16-12 UNC 1-5/16-12 UNC 1-5/8-12 UNC 1-7/8-12 UNC 7,5 10 12 15 25 40 60 70 80 110 150 5,5 7 9 11 20 30 45 50 60 80 110 8 12 15 25 45 60 100 120 140 190 220 6 9 11 18 35 45 75 90 105 140 160
z oae4e
B-WIth 0-rlng
WWlth cone
A-Thread size
Z103949-ZI21005AE-011O84
TM-4476 (Jan-90) K9 Printed in Germany
10-05-3
JDWZ Combines
11
ENGINE REMOVAL AND INSTALLATION
Section 20
CONTENTS OF THIS SECTION NOTE. Combine engines
are included in a sepa- rate engine technical
manual. The details in this section apply
specifically to combine engine installation. GROUP
05 - REMOVAL AND INSTALLATION - 4 CYLINDER ENGINE
Electrical connections Fuel lin Speed
con Hydraulic control valve connection
20-05-2
Separate engine from Lifting engine Engine
installation GROUP 10 - REMOVAL AND INSTALLATION
- 6 CYLINDER ENGINE
Fuel lin Speed control linka Hydraulic control
valve connections Heater hose connectio
0-2 0-2
0-2 20-10-3 0-4
Separate engine from
Lifting en Engine installation
0-5 -10-5
20-1
TM-4476 (Jan-90)K9 Printed in Germany
JDWZ Combines
12
Group 05 REMOVAL AND INSTALLATION - 4 CYLINDER
ENGINE JDG-23 SPECIAL TOOLS
B JD-244
A-dDG-23 Lifting bracket B-JD-244 Lifting eyes
Z103901
PREPARATIONS IMPORTANT Lower feeder conveyor to
ground to relieve pressure in hydraulic
system. Disconnect ground (-) and positive ( -I-)
cables at the battery and remove battery. Z
100210-ZI82005AE-111189
ELECTRICAL CONNECTIONS - STARTING MOTOR Remove
all cable connections at starting motor (A) and
starting circuit relay (B).
Z103903 ZI22005A E 011084
ELECTRICAL CONNECTIONS - ALTERNATOR Remove both
connections (A) at alternator.
Z 103904-ZI22005AE 011084
20-05-1
TM-4476 (Jan-90)K9 Printed in Germany
JDWZ Combines
13
Removed and lnstetlatlon - 4 Cylinder
Engine VARIOUS SENDING UNIT CONNECTIONS Remove
connectors at coolant temperature sending unit
(A), at engine oil pressure sending unit (B) and
at alr Intake sendlng unit. If instaJled, remove
connector of cold start aid.
FUEL LINES Dlsconnect fuel inlet line (A) and
return line (B). On engines with cold start aid,
remove return line at cold aid.
SPEED CONTROL LINKAGE Open wire seal at ball
oint (A) and separate Ilnkage (B) at fuel
lnjectlon pump.
.
.
Disconnect cables at control vaNe (A) and bracket
(B). Disconnect all hoses with the exception of
the pressure line from the hydraulic pump and the
return line to hy- draulic reservolr. Seal all
openings immediately with plastic plugs.
30-05-2
JDWZ Combines
TM-4d76 (Jan-SI)K9 Printed in Germany
14
Removal and Installation 4 Cylinder
Enpine DRIVE BELTS Remove straw chopper V-belt
(A), unloading auger drive belt (B), ground drive
belt (C) and flat belt (D). Remove both belt
guides (E). Remove cotter pin of belt tensioner
pulley bracket (F).
A-Chopper V-belt BUnIoadlng auger drlve belt
C-Ground drive belt DFlat belt E-Belt
gulde F-Pulley bracket
Z103810-ZI22005AE-011084
REMOVE GUARDS Remove right-hand side panel (A)
and right-hand engine cover (B).
Z1O3911 Z103911 -ZI22005A E 011084
SEPARATE ENGINE FROM
COMBINE FRAME IMPORTANT Before removal mark
position of engine on combine. Mark position on
combine and engine mountings both laterally and
IongItudInaIIy. These markings are essential for
correct alignment when relnstalllng engine.
Remove four mounting bolts (A) of engine mounting
on right and left-hand sides.
20-05-3
TM-4476 (Jan-90) K9 Printed in Germany
JDWZ Combines
15
Removal and Installation 4 Cylinder Engine
T..
LIFTING ENGINE Attach lifting eyes JD244-1 and
JD244-2 to engine. Attach lifting bracket JDG-23
to lifting eyes. Lift engine with a hoist and
slide to right out of combine. At the same time
pull tension pulley on the left hand side from
bracket (A).
""""'" "" ' " "' "
'""" .
"" "" ' -
Z103913,Z103914-ZI22005AE-011084
ENGINE INSTALLATION Install engine in reverse
removal procedure. While installing engine, place
tension pulley on bracket (A). After installing
engine, check levels of engine oil and coolant.
Align engine with markings carried out during
engine removal. After engine test run, check all
attaching screws again for tightness. Check all
drive belts (ground drive, hydraulic pump drive,
separator drive and un- loading auger drive) for
correct adjustment, true run- ning and
tension. In the position "Fast Idle" the stop
control lever of the fuel injection pump must
slightly contact its stop if not, readjust speed
control linkage. Z103915-ZI22005AE-011084
20-05-4
TM-4476 (Jan-90)K9 Printed in Germany
JDWZ Combines
16
Group 10 REMOVAL AND INSTALLATION - 6 CYLINDER
ENGINE
JOG-23
A
SPECIAL TOOLS
B o.x
AJDG-23 Lifting bracket B-JD-244 Lifting eyes
Z103901 Z103901 ZI22005A E 15 188
PREPARATIONS IMPORTANT Lower feeder conveyor to
ground to relieve pressure in hydraulic
system. Disconnect ground (-) and positive ( -I-
) cables at the battery and remove
battery. Z100210-ZI82005AE-111189
ELECTRICAL CONNECTIONS -
STARTING MOTOR Remove all cable connections at
starting motor (A) and starting circuit relay (B).
A-
Z103917 ZI22010AE-011084
ELECTRICAL CONNECTIONS - ALTERNATOR Remove both
connections (A) at alternator.
Z103918 ZI22010AE 011084
20-10-1
TM-4476 (Jan-90) K9 Printed in Germany
JDWZ Combines
17
Suggest If the above button click is invalid.
Please download this document first, and then
click the above link to download the complete
manual. Thank you so much for reading
18
Removal and Installation 6 Cylinder Enpine
VARIOUS SENDING UNIT CONNECTIONS Remove
connectors of following sending units A-Coolant
temperature sending unit B-Englne oil pressure
sending unit C-Air intake sending unit E-Cold
start ald connector
Z103919-ZI22010AE
FUEL LINES Disconnect fuel inlet line (A) and
return hose (B) at cold start aid, or directly at
return line
Z103920-ZI22010A
'
SPEED CONTROL LINKAGE Open wire seal at ball
joint (A) and separate linkage (B) at fuel
injection pump.
ZI2201OAE
HYDRAULIC CONTROL VALVE Disconnect cables at
control valve (A) and bracket (B). Disconnect all
hose connections with the exception of the
pressure line from the hydraulic pump and the re-
turn line to hydraulic reservoir. Seal all
openings immediately with plastic plugs.
20-10-2
JDWZ Combines
TM-4476 (Jan-90)K9 Printed in Germany
19
https//www.ebooklibonline.com Hello dear
friend! Thank you very much for reading. Enter
the link into your browser. The full manual is
available for immediate download. https//www.ebo
oklibonline.com