FIVE STEPS TO AVOID BEARING FAILURE

1
FIVE STEPS TO AVOID BEARING FAILURE

• Imagine you are driving your motorcycle and you
  hear a deep rumbling sound from the stomach of
  your vehicle. Has it ever happened to you? It is
  enough to scare any sane person. Have you ever
  wondered why electrical appliances make noise
  after a certain period of consistent use? Well,
  it is because of the bearings within them.
  Regardless of who your bearing supplier is,
  bearings tend to fail at times.
• Bearing failures are not uncommon, but they can
  prove to be fatal if left untreated. Before we
  discuss how to avoid bearing failure, you must
  understand the common causes that lead to bearing
  failures. Why do bearings stop working
  efficiently? We will tell you why!
• Corrosion - When water or any other liquid enters
  your appliance and touches the bearings, they
  might get corroded. 
• Contamination - Dirt, dust, sand, chemicals, and
  other such unwanted substances may contaminate
  your bearings.
• Improper Lubrication - Too much or too little
  lubrication is not good for bearings. Either way,
  they will start wearing and stop functioning
  efficiently. You must lubricate your bearings as
  recommended by the bearing manufacturers in
  India.
• Poor-fitting - If the bearings are not inserted
  properly, or if the measurements and fitting are
  not correct, it might lead to bearing failure.
• The above mentioned are some causes that lead to
  bearing failure. Bearings are important for any
  machine, any gadget to function properly. If
  bearings are worn out and stop working, it may
  lead to accidents.
• How can you avoid bearing failures? We have
  mentioned a few simple steps that may help you
  keep your bearings intact and running.

2

• 1. Do Not Let Your Bearings Corrode
• You can buy your bearings from the best bearing
  company in India, but if you are not careful,
  they will corrode. Corrosion occurs when bearings
  come in contact with water or any other corrosive
  liquid. The corrosion starts from the surface
  which slowly contaminates the entire bearing.
  Gradually, the bearing starts cracking. The first
  signs of corrosion are red or brown rust on the
  surface. Once the surface starts corroding, there
  is not much you can do to prevent it. However,
  you can make sure your bearings do not corrode.
• You can buy bearings made of materials that do
  not corrode. However, proper lubrication at
  certain time intervals helps prevent corrosion.
  To be extra careful, you can use lubricants with
  rust inhibitors. When you clean your vehicle or
  gadget with water, make sure the water does not
  seep within the outer cover. You can secure your
  bearings, whether they are taper roller bearings
  or ball bearings, with a little care and
  precaution.
• 2. Use Proper Lubricants
• We use lubrication so friction does not wear down
  the bearings. You must have seen the soles of
  your chappal getting worn after frequent use.
  This happens due to friction. When any machine
  runs, friction is produced. The role of bearings
  is to lower the friction and keep the machine
  running smoothly. However, friction can be
  reduced and not avoided. This is why you must use
  lubricants at proper time intervals. Sometimes,
  regular lubrication will not work. If the machine
  or appliance needs high speed and temperature,
  special lubricants may be required. Based on what
  the machine is and what type of bearing it has,
  the lubricants will differ. Say, a machine in an
  industry dependent on angular roll ball bearing
  might require more amount of lubrication. You
  must also remember that more grease can result in
  bearing failure. Use the right lubricant in the
  right amount.

3

• 3. Do Not Let Your Bearings Contaminate
• Dust can enter your vehicle or appliance. When
  dust gathers over bearings, it reduces mobility
  and the bearings can not function properly. And
  you know what happens when your bearings do not
  function well.
• What can you do to avoid the contamination of
  bearings? Well, you take proper care of your
  gadgets. We understand that dust particles are
  minute. This is why you must use a closure for
  your gadgets so dust can not harm the bearings
  working within. You must contact your bearing
  supplier regarding the same. Find out which
  closure suits your appliance the best. Take
  expert advice, and do not let your bearings
  contaminate.
• 4. Balance Your Appliance Well
• How many times do you need to call a technician
  to repair your fan? It happens quite a lot, does
  it not? The fan keeps making sounds during summer
  and even stops working at times. It may happen
  because of imbalance. If your fan is imbalanced,
  the bearings that keep it working face more load.
  This causes the bearings to wear out after a
  certain period which causes your fan to stop
  working.
• However, that was just one example. The bearing
  manufacturers in India receive complaints of
  machines not functioning properly every day. This
  mostly happens because of imbalance. Certain
  things can lead to an imbalance within the
  machines. It may be because your technician did
  not quite repair the machine properly. Ensure
  your machine is properly balanced. Ensure the
  bearings are not overloaded and worn out.

4

• 5. Do Not Be Hasty With Bearing Installation
• You might try and install the bearings yourself
  to save a few rupees. You must know that sheer
  force does not work with bearing installation.
  There are certain methods, including heat which
  help with the proper and smooth installation of
  bearings. You must always contact a bearing
  company in India or an experienced mechanic who
  can help with bearing installation. In trying to
  save a few rupees, you might unknowingly destroy
  the appliance.
• Once the installation process finishes, clean the
  bearings and lubricate them. Make sure you use
  the lubricants the manufacturing company
  suggested.
• Conclusion
• Bearings are the joints that keep every machine
  running. This is why you must take proper
  measures to ensure they dont fail and keep
  functioning smoothly. In case you are looking for
  a bearing supplier, you have come to the right
  page.
• NBC, the leading manufacturer and supplier of
  bearings in India, is the symbol of reliability,
  quality, and durability. Our bearings function as
  smoothly as butter, ensuring your gadget runs
  properly. Get in touch with us at your
  convenience!
• Original Sourcehttps//site-2933131-7800-5603.my
  strikingly.com/blog/five-steps-to-avoid-bearing-fa
  ilure