Surface deburring, polishing, shinning and finishing machines

1
Deburring and Surface Polishing machines

• www.metallurgyproducts.com
• 919810868858

2
Circular Vibratory Polishing Machines

• Deburring and polishing vibrator machines
• The Vibrator Finishing Machines are mass
  finishing machines used for deburring, polishing,
  descaling and surface treatment of different
  metal and plastic components. Vibratory tumble
  finishing systems produce a cutting action by
  shaking the processing vessel (finishing tub) at
  a high speed thus causing the tumbling media and
  parts to scrub against each other and this
  scrubbing action removes burrs on the surfaces as
  rotating in eccentric motion weights mounted on
  the tub produces this shaking action of the tub
  which produces a cutting action that is very
  thorough and removes material from pockets and
  recesses on the surface therefore it is used for
  delicate or intricate parts too. This motion with
  high speeds and a short stroke can also run large
  bulky parts without damage such as Large wing
  spans and casted goods. The action is that of a
  small orbit at a high speed and thus is very
  powerful and causes little stress on the parts
  being polished.
• The finishing and deburring process is increased
  in vibratory barrels due to the relative motion
  between finishing media and the pieces as
  vibrations are generated and with the help of
  three dimensional vibrations and thus the process
  becomes more effective which is controlled by
  amplitude and frequency of the vibrations
  generated by mounted weights, which imparts
  higher force than the gravitational force. These
  machines can be harmonized to promote the best
  possible action and movement in deburring and
  polishing the surfaces, which will itself impart
  an achievable quality on polished components. Our
  machines with thick polyurethane inner lining
  with high quality specification has a longer life
  before replacement compared to our competitors,
  further Initially to prevent metal stress that
  the vibration may cause on the work process
  chamber the metalwork may be heat treated to
  normalize the structure. The vibratory motion
  setting in the machinery can be adjusted with the
  help of regulated motor speed and suspended
  weights

3
Circular Vibratory Polishing machines
4
Linear or Tub type vibratory finishing machine

• Mainly used for processing parts made of metals
  both ferrous non-ferrous and nonmetals, It is
  especially suitable for polishing long parts and
  the parts with complicated and irregular cavities
  and shapes for finishing high-volume materials in
  short-cycle of de-burring and finishing, it
  improves surface finish, de flash, remove tool
  marks of stampings forgings, to accommodates
  parts of varying size and shapes separate
  chambers are provided, In these machines variable
  speed and adjustable eccentric weights can be
  closely adjusted to vary the vibratory forces to
  exact degrees and get optimum polishing and
  deburring results which permits action ranging
  from very aggressive to remove heavy burrs and
  extremely gentle action for fragile parts. After
  processing there is no damage to the original
  shape or precision of dimensions of the processed
  parts and this type of polisher is suitable for
  the surface polishing of large quantity and batch
  of medium and large-sized parts

5
Linear or Tub type vibratory finishing machine 
6
High energy Centrifugal deburring and Finishing
Machines

• Centrifugal barrel finishing machines is used in
  wide variety of sizes to fit any surface
  finishing needs for fast polishing and
  de-burring, these tumbling machines are the
  versatile and money-saving solution for polishing
  and de-burring and are the fastest and most
  economical form of finishing machine available,
  Used for polishing engine blades in the aerospace
  industry to delicate heart valves and medical
  implants. These machines are used for
  comprehensive treatments of finishing (roughing,
  grinding, deburring and polishing) on objects
  big, small and very small such as goldsmith
  industry,and can operate both dry and wet
  deburring and polishing. Combination of movements
  in machines incorporate the spin speed of a main
  course of single, double or four containers whose
  orbit which in turn rotate around its axis but in
  the opposite direction to the main course,
  combined with the particular shape of the inner
  containers made of polyurethane (anti-wear and
  anti-aging ) allow to reach very results driven
  finishing in a matter of minutes. The machine can
  clean up pieces of metal, acrylic or rubber parts
  in minutes.The finish achieved by these machines
  is isotropic meaning parts are polished uniformly
  and evenly and Variable speed control allow these
  tumbling machines to achieve whatever finish the
  operator desires, from a simple polish at low
  speed, to full scale de-burring and edge
  radiusing and higher rotational speeds.

7
Centrifugal deburring and Finishing high energy
Machines
8
Magnetic Shiner And Polisher Machine

• Magnetic polisher comprises of a container and a
  series of magnets from 4 to 32 in numbers that
   rotate at an adjustable speed and finishing
  media consists of micro-needles of martensitic(
  which is a very hard form of steel crystalline
  structure) stainless steel which  are
  Ferro-magnetic, where  motor contained in the
  base spins a heavy disc with different
  high-powered magnets attached on it, this creates
  a magnetic field which in turn makes the magnetic
  steel pins jump randomly in and around the pot or
  barrel, these needles which are driven by the
  rotation of the magnets continuously and
  uniformly hit the surfaces to be finished to
  provide a burnishing action and remove any
  investment residues and surface oxides and
  gradually polishing the surface of the metal,
  This particular type of movement of the finishing
  medium, which is controlled by the dynamic
  magnetic fields makes the magnetic barrel
  finishing  very similar to the action of a
  brushing the surface. This polisher is great for
  more delicate work such as jewelry and filigree
  designs. It is also quieter, quicker and easier
  to fill and empty compared with the rotary
  tumbler and very economical to run. Simply
  quarter-fill the acrylic drums or barrel with
  water and add the stainless-steel pins and your
  work. Add about a quarter of a teaspoon of
  cleaning or anti tarnish compound, the steel
  media you receive with the magnetic polisher is
  made from tiny 5mmx0.3mm steel pins made of
  stain-resistant magnetic stainless steel.

9
Magnetic Shiner And Polisher Machine
10
Ultrasonic Cleaning Finishing Machine

• Ultrasonic cleaning machines uses ultrasound
  (usually from 20400 kHz) and an appropriate
  cleaning agent to clean items and can be used
  with just water and a solvent appropriate for the
  item to be cleaned along with the soiling
  enhancing the effect. Cleaning time normally
  lasts between three to six minutes but can also
  exceed depending on the contamination levels in
  the product, in Ultrasonic cleaning machines
  bubbles are produced by high frequency pressure
  (sound) waves to agitate a liquid and hence high
  forces on contaminants adhering to substrates
  like metals, plastics, glass, rubber, and
  ceramics. This action also penetrates into cracks
  and recesses. The intention is to thoroughly
  remove all traces of contamination onto solid
  surfaces which can include dust, dirt, oil,
  pigments, rust, grease, algae, fungus, bacteria,
  lime scale, polishing compounds, flux agents,
  fingerprints, soot wax and mold release agents,
  biological soil like blood and so on. Ultrasonic
  can be used for a wide range of work piece
  shapes, sizes and materials, may not require the
  part to be disassembled prior to cleaning also
  the solution contains a good wetting agent
  (surfactant). Aqueous cleaning solutions contain
  detergents, wetting agents, water compounded with
  Alkali, Surfactants, Water conditioners,
  Corrosion inhibitors, Foam stabilizers and other
  components

11
Ultrasonic Cleaning Finishing Machine
12
Centrifugal deburring and Finishing high energy
Machines

• Centrifugal barrel finishing machines is used in
  wide variety of sizes to fit any surface
  finishing needs for fast polishing and
  de-burring, these tumbling machines are the
  versatile and money-saving solution for polishing
  and de-burring and are the fastest and most
  economical form of finishing machine available,
  Used for polishing engine blades in the aerospace
  industry to delicate heart valves and medical
  implants. These machines are used for
  comprehensive treatments of finishing (roughing,
  grinding, deburring and polishing) on objects
  big, small and very small such as goldsmith
  industry,and can operate both dry and wet
  deburring and polishing. Combination of movements
  in machines incorporate the spin speed of a main
  course of single, double or four containers whose
  orbit which in turn rotate around its axis but in
  the opposite direction to the main course,
  combined with the particular shape of the inner
  containers made of polyurethane (anti-wear and
  anti-aging ) allow to reach very results driven
  finishing in a matter of minutes. The machine can
  clean up pieces of metal, acrylic or rubber parts
  in minutes.The finish achieved by these machines
  is isotropic meaning parts are polished uniformly
  and evenly and Variable speed control allow these
  tumbling machines to achieve whatever finish the
  operator desires, from a simple polish at low
  speed, to full scale de-burring and edge
  radiusing and higher rotational speeds.

13
Centrifugal deburring and Finishing high energy
Machines
14
Sand blasting, deburring Polishing Machines

• There are different types of blasting equipment
  and all of these types of machines can handle a
  variety of blast media. These shot blasters come
  in a variety of sizes and types. The most
  versatile and valuable portable blasting
  equipment can blast all types of dry blast media
  without requiring changes in structure..
• Types of Media generally used for blast finishing
• Aluminum oxide, White aluminum oxide.
• Urea and other plastic abrasives.
• Corn cob grit.
• Walnut shell grit.
• Glass beads.
• Pumice (a type of grey stone that is very light
  in weight).
• Crushed glass grit.
• Steel grit.
• Silicon carbide.
• Steel shot.
• Abrasive plastic.

15
Sand blasting, deburring Polishing Machines
16
Metallurgy Products

• We represent for mass deburring and polishing
  machines, media and technology from around the
  world and offer complete product line of mass
  finishing processes to the users. The machines
  are maintained and serviced asper the guide lines
  of the manufacturer with critical calibrations on
  regular basis. Provide effective and professional
  representation of the manufacturers which is key
  to achieve better business and brand
  representation by promoting online and offline
  and maximizing the penetration towards growth and
  expansion of the business with the expertise and
  knowledge about surface finishing process.
  Application and business verticals and
  harmonizing the process with requisite competent
  manpower in representing reputed entity as it
  requires sense of commitment and we imbibe the
  culture of our partners and act as their
  mouthpiece. This expertise drawn in surface
  finishing is from many years of hard work and
  extensive field trials which is the key factor
  behind the success of our services giving desired
  results in surface finishing by developing
  innovative polishing processes and increasing the
  productivity and replacing the rework with hand
  resulting in better performance excellence,
  increase in productivity, reducing operating
  costs to the customers satisfaction.
• www.metallurgyproducts.com , 919810868858/919810
  068858