Title: ECET 110 Knowledge is divine / snaptutorial.com
1ECET 110 Knowledge is divine / snaptutorial.com
2ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Quiz 2 For more classes
visit www.snaptutorial.com 1. (TCO 4) For the
series-parallel circuit given in Figure 3.1
below, determine the total resistance RT between
the terminals labeled A and B 2. (TCO 4) For the
circuit given in Figure 3.3, obtain the following
quantities.
3ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Quiz 3 For more classes
visit www.snaptutorial.com 1. (TCO 7) For the
circuit given below, determine the total
capacitance CT between the terminals labeled A
and B. 2. (TCO 6) Find the Thevenin equivalent
circuit for the circuit given in Figure 4.7
below. Consider the resistor R to be the variable
load resistor. Determine the current through R
when R75 ohms and also when R25 ohms. 3. (TCO
7) For the RC circuit given below, determine the
steady state voltage across the capacitor and the
peak current through the capacitor during its
charging cycle
4ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 1 Homework For more classes
visit www.snaptutorial.com Why do you never
apply an ohmmeter to a live network? What is the
voltage across a 220 ? resistor if the current
through it is 5.6 mA? What is the current through
a 6.8 ? resistor of the voltage drop across it is
24V?
5ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 1 iLab Analysis of a Series Circuit
using Simulation and Actual Construction For
more classes visit www.snaptutorial.com Objectiv
es To construct a circuit in series to test and
verify Ohms Law and Kirchhoffs Voltage Law
using a multi-meter, breadboard, resistors and
jumper wires. To simulate this construct
digitally and mathematically to compare results
to determine if the above laws are supported.
6ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 2 Homework For more classes
visit www.snaptutorial.com CHAPTER 6 4. For
each circuit board in Fig. 6.74, find the total
resistance between connection tabs 1 and 2. 10.
For the network of Fig. 6.80
7ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 2 iLab Analysis of a DC Parallel
Circuit using Simulation and Actual Construction
For more classes visit www.snaptutorial.com Obj
ectives The objectives this week were to
effectively learn to simulate and construct a
parallel circuit and learn to troubleshoot issues
that may be had by OPEN or Shorted circuits.
Also to learn how to calculate current and
resistance within parallel circuits Did you prove
Kirchhoffs Current Law to be
8ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 2 Quiz For more classes
visit www.snaptutorial.com 1. (TCO 3) Find the
total conductance and total resistance of the
parallel circuit given below.
9ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 3 Homework For more classes
visit www.snaptutorial.com Chapter 7 Problems
1 (a, b, c), 2 (a, b), 3, 8, 10 1. Which elements
(individual elements, not combinations of
elements) of the networks in Fig. 7.60 are in
series? Which are in parallel? As a check on your
assumptions, be sure that the elements in series
have the same current and that the elements in
parallel have the same voltage. Restrict your
decisions to single elements, not combinations of
elements. 2. Determine RT for the networks in
Fig. 7.61.
10ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 3 iLab Analysis of a DC
Series-Parallel Circuit For more classes
visit www.snaptutorial.com Objectives To
construct a series-parallel circuit correctly and
measure its equivalent resistance.
11ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 4 Homework For more classes
visit www.snaptutorial.com Objectives 1. To
troubleshoot a complex circuit and determine
various currents and voltages using format mesh
analysis. 2. To simulate the complex circuit in
MultiSim and record the required quantities.
12ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 4 iLab Format Mesh Analysis For
more classes visit www.snaptutorial.com Objectiv
es 1. To troubleshoot a complex circuit and
determine various currents and voltages using
format mesh analysis.
13ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 5 Homework For more classes
visit www.snaptutorial.com CHAPTER 9 1a. Using
the superposition theorem, determine the current
through the 12 Ohm resistor of fig. 9.119. we
will use superposition to analyze this circuit.
First short E2 and find the current thru the 12
Ohms resistor and then Short E1 and keep E2 in
the circuit and find the same current. Then
algebraically add the two currents (add if in the
same directions and subtract if opposite direction
14ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 5 iLab Thevenins and Superposition
Theorem For more classes visit www.snaptutorial.
com Objectives 1. To troubleshoot a complex
circuit and determine various currents and
voltages using superposition theorem and compare
the results with the results of last weeks
lab. 2. To simulate the complex circuit in
Multisim and record the required qu
15ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 6 Homework Capacitors For more
classes visit www.snaptutorial.com Chapter
10 Capacitors
16ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 6 iLab Transient Analysis of a
Resistor-Inductor Circuit For more classes
visit www.snaptutorial.com 1.
OBJECTIVES Perform a transient analysis on a
Resistor-Capacitor circuit, and measure capacitor
charge
17ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 6 Quiz For more classes
visit www.snaptutorial.com 1. (TCO 7) For the
circuit given below, determine the total
capacitance CT between the terminals labeled A
and B
18ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 7 Homework For more classes
visit www.snaptutorial.com Chapter 11
Inductors
19ECET 110 Knowledge is divine / snaptutorial.com
ECET 110 Week 7 iLab Transient Analysis of a
Resistor-Inductor Circuit For more classes
visit www.snaptutorial.com Objectives Calcula
te time constant, transient time, current and
voltage across inductor at beginning and the end
of the charge cycle. Use MultiSim to test the
calculations. Build and test a physical circuit
using the MultiSim schematic.
20ECET 110 Knowledge is divine / snaptutorial.com