Why Do You Need Pre Terminated Fiber Solutions?

1
Why Do You Need Pre Terminated Fiber Solutions?
2
INTRODUCTION
Todays modern data center proposition continues
to promote the hot topics around consolidation,
reduced operating expense, flexibility,
scalability and of course being as Green as
possible along the way. When you are building
a custom fiber network it is essential to
purchase quality cable assemblies. Never waste
time or money terminating fiber cable in the
field again. Save yourself and your team lot of
time and trouble, and eliminate all performance
worries with Pre Terminated Fiber Cable from
FalconTech. Youll get top-quality fiber cable
thats built to your exact specs, fully tested,
and shipped ready for installation so you can
take care of business. Below you will find
information on standard options and components
available for Pre Terminated Fiber Optic Cable
assemblies.
3
PRE TERMINATED FIBER OPTIC CABLE
A Pre Terminated Fiber optic cabling system is
one that contains cables and the necessary
modular components with the accompanying
connectors already attached. For optimum quality
assurance, each part of the system is tested
before it is shipped to the customer. A pre
terminated fiber optic cabling system may contain
any of the following, depending on the customers
needs

• Comes with a Swivel Pulling Eye
• A swivel pulling eye is attached to protect
  against stresses associated with pulling the
  fiber optic assembly into position during
  installation. The pulling eye acts as a strain
  relief by distributing the stress over the outer
  jacket and eliminating it from the fiber optic
  strands.

Continue....
4

• Comes on a Triple Flange Spool
• Long preterminated fiber optic assemblies are
  shipped on a triple flange spool to provide
  protection for the connectors on both ends. The
  additional flange also allows the end of the
  assembly to remain safely coiled and protected
  from bending, twisting and tangling while the
  cable is run out. The inner end can then be
  unwound and connected.

PRE TERMINATED FIBER OPTIC CABLE

• Direct Burial
• Direct-Buried Cable (DBC) is designed to be
  buried under the ground without any additional
  covering, conduit or sheathing to protect it.
  This Outside Plant (OSP) fiber optic cable
  includes water-blocking characteristics and an
  armored jacket to prevent damage from rodents and
  the pressure created by the surrounding dirt and
  rock.

• Interlocking Armor
• Fiber optic distribution cable encased in
  interlocking aluminum armor is ideally suited for
  harsh environments such as direct buried outside
  plant applications, industrial and heavy traffic
  areas, and data centers where cables are
  installed under the floor.

Continue....
5

• Indoor/Outdoor
• Indoor/Outdoor cable (I/O cable) is designed to
  withstand the environmental conditions
  experienced outdoors. Dry water-blocking
  features, such as water-swellable Aramid, protect
  against water ingress.

PRE TERMINATED FIBER OPTIC CABLE

• Aerial Cable
• Aerial rated cable is strong enough to withstand
  the tension between structures through the
  incorporation of a strengthening feature such as
  a messenger cable or a central strength member.

• Tini Armor Uni-Boot
• This cable option features fiber optic cable
  encased in a small OD stainless steel miniature
  armor. The 3mm outside diameter is more than 65
  smaller and 75 lighter than standard
  interlocking armor and still maintains
  flexibility. The coiled armor offers protection
  and durability and may eliminate the need for
  conduit.

• Plenum / PVC
• The plenum options include OFNP (Optical Fiber
  Nonconductive Plenum) and OFCP both of which have
  the fire-resistant and low smoke producing
  characteristics needed to meet The NEC
  requirements for cabling installed in a plenum
  space and not residing in conduit.

6
AVAILABLE CABLE TYPES
PRE TERMINATED FIBER OPTIC CABLE
Now you can install your own fiber optic cables
without investing in training and equipment.
Custom Factory terminated, pre-tested and ready
to pull. Made to lengths of up to 5000 feet.
These assemblies can be ordered in either indoor
or outdoor variations, and in 6, 12 or 24 strand
fiber counts, in Multimode OM1, OM2, OS2, OM3
and OM4 or Singlemode!

• OM1 -- Falcon Technologies preterminated
  multimode OM1 fiber optic distribution assemblies
  utilize 62.5 micron Corning glass in a tight
  buffer design. These trunk cables provide a high
  speed infrastructure backbone pathway available
  in indoor/outdoor plenum (OFNP) and riser (OFNR)
  armored and non-armored.

Continue....
7
AVAILABLE CABLE TYPES

• OM3/OM4 -- Falcon Technologies preterminated
  multimode OM3 and OM4 fiber optic distribution
  assemblies utilize 50 micron Corning glass in a
  tight buffer design. These 10 Gigabit, laser
  optimzed trunk cables provide a high speed
  infrastructure backbone pathway available in
  indoor/outdoor plenum (OFNP) and riser (OFNR)
  armored and non-armored.

• OS2 -- Falcon Technologies preterminated
  singlemode OS2 fiber optic distribution
  assemblies utilize 8.3 micron (sometimes seen as
  9 micron in the nomenclature) Corning glass in a
  tight buffer design. These trunk cables provide a
  high speed infrastructure backbone in a long
  distance pathway available in indoor/outdoor
  plenum (OFNP) and riser (OFNR) armored and
  non-armored.

8
FEATURES AND BENEFITS
AVAILABLE CABLE TYPES

• Lower Total Cost Forget about costly
  connectors, consumables, and gear, plug the work,
  time, and testing required for field fiber optic
  link end. Our Pre Terminated fiber optic links
  spare where it matters most. FalconTech fiber
  links make end basic.

• Proven Performance Get top execution with no
  field end errors. All Black Box pre-ended fiber
  links experience broad investigation and testing
  and accompany a lifetime ensure. Rely upon
  FalconTech for the majority of your fiber link
  needs.

• Quick Turnaround Most FalconTech pre-ended
  fiber links are turned around in under seven
  daysnow and then even in a day. Never be
  helpless before trusting that links will show up
  again.

9
AVAILABLE CABLE TYPES

• Faster Deployments Cut installation time and
  labor costs by 70 to 80 with pre-terminated
  fiber cable. Because it arrives ready for work,
  deployments are as easy as plug-n-play. Fiber
  optic termination made easy.

• Fiber Cables Your Way Just specify the core,
  cable type, jacket, connector, strand count,
  breakout, labeling, staggering, and if you want a
  pulling eye. With FalconTech, your fiber cable
  solutions feel custom made for you and your team.

10
CONCLUSION
AVAILABLE CABLE TYPES
Our fiber optic cables are made by FOA Certified
technicians in the USA by Falcon Technologies
Inc. using the latest epoxy injection and
polishing systems for the highest quality and
performance. The end faces of the Corning glass
within our assemblies are machine polished,
resulting in a much lower light loss than can be
achieved by hand polishing. All pre terminated
fiber products are guaranteed and 100 tested.
11
CONTACT US
AVAILABLE CABLE TYPES

• Next Day Service Available
• Falcon Made Assemblies In Usa
• Call 866-958-4499 For Immediate Service

Request A Quote
FIND US