Durability Years will be Shortened of Asphalt Pavement

1
Durability Years will be Shortened of Asphalt
Pavement
Next
2
What I discuss in this section

1. Asphalt paving work process 1 Roadbed
2. Asphalt paving work process 2 Underground roadbed
3. Asphalt paving work process 3 Upper layer roadbed
4. Asphalt paving work process 4 stratum
5. Asphalt paving work process 5 Surface layer
6. My Company Introduction
7. Our Services
8. How We Can Be Found?

Next
Previous
3
MEANING OF BASIC ASPHALT PAVEMENT PROCEDURE AND
PROCESS

• When you want to pave your driveway or parking
  lot you have to follow these necessary steps.
  Asphalt pavement construction has roughly divided
  into five stages, Roadbed, Underlying Road,
  Upper Road, Substrate and Surface from the
  bottom.
• Here, l will explain the contents of each process
  together with the effects obtained by that
  process.

Next
Previous
4
Asphalt paving work process 1 Roadbed

• It is the lowest layer of pavement, laying the
  part called roadbed.
• Since the roadbed is located at a depth of about
  1 meter (for commercial use and it increases or
  decreases according to the use) from the road
  surface, I start with digging work to dig into
  that depth. Now you have need to lay sand in the
  ditches that have been dug and build a foundation
  for paving. Since the load on the pavement
  surface will eventually be received on this road
  floor, if the road floor is weak, problems such
  as ground subsidence may occur.
• If the ground is too vulnerable, we may reinforce
  the ground by burying reinforcing bars

Next
Previous
5
Asphalt paving work process 2 Underground roadbed

• Roadbed is a part that supports the midpoint of
  pavement, and it has the role of distributing
  loads and shocks to upper and lower layers,
  respectively.
• You will have to lay down crushed stones and
  gravel on the roadbed where we have finished
  laying.
• It is said that many of the crushed stones used
  for the lower roadbed are relatively large in
  order to secure the load firmly.

Next
Previous
6
Asphalt paving work process 3 Upper layer roadbed

• Here will also need to lay down crushed stone in
  the upper layer of the roadbed as well. The upper
  roadbed has the role of uniformly receiving the
  load transmitted from the base just above and
  distributing it to the lower layer, so many
  crushed stones are relatively small. In order to
  reduce the loss of load distribution as much as
  possible, crushed stone with the uniform size is
  used. After crushing the crushed stone, press it
  with a road roller, etc.
• By firmly compressing to the prescribed density,
  you can get a solid foundation.

Next
Previous
7
Asphalt paving work process 4 stratum

• It is a layer laid on the roadbed, the material
  from here becomes asphalt. Because the base layer
  is a layer that becomes a cushion between the
  upper roadbed and the upper surface layer, the
  asphalt used will be rich in flexibility.
• Although it is being done, the top road surface
  of the crushed stone is covered with soft
  asphalt, and more working to increase the
  adhesion to the surface layer.

Next
Previous
8
Asphalt paving work process 5 Surface layer

• The uppermost part of the pavement, the layer of
  asphalt that you usually see is called the
  surface layer.
• Asphalt which emphasizes durability rather than
  flexibility is used for the surface layer
  supported by the base layer.
• It will distribute the load and impact on the
  road surface to the base layer and keep the road
  surface flat so that user can comfortably pass
  through.
• The asphalt paving companies also do the work
  called remaining bulk which tilts towards
  drainage so that water does not accumulate on the
  road surface.

Next
Previous
9

• After the overgrowth has been completed, perform
  a rolling operation that treads asphalt spread
  as a finish with a roller or the like. The
  asphalt just laid is soft and fluffy, but it will
  become a hardened road surface by rolling
  pressure.
• In that case, care is necessary for temperature
  management. Asphalt softens at high temperature
  and solidifies as it cools, but it will cause
  distortion and cracking if it cools down during
  rolling.
• In order to finish on a beautiful paved surface,
  it is necessary to keep rolling while maintaining
  sufficient temperature.
• Special tools and materials used in the
  construction of asphalt pavement work. Paving
  work of asphalt is done by dedicated vehicle,
  heavy machine, and equipment.
• Read the topic introduction of tools used for
  construction together with materials.

Next
Previous
10
Standard Paving Inc.From roadway to driveway
WHO ARE WE
Next
Previous
11
Our Introduction

• Standard Paving Inc. is one of the most famous
  pavers in Virginia. We have been providing our
  services for last 3 decades. We are experts in
  expedited repair as well as renewal of your of
  current parking lots. We have done many projects
  based on replacing parking lots and to repair
  damaged roads. We have also made a number of
  private roadways and commercial roads.

Next
Previous
12
Our Services

• Commercial Roads
• Parking Lots
• Parking Lots Repair
• Private Roadway
• Striping

Next
Previous
13
Why Choose us ?

• Professional
• Free Estimate
• Employment
• Asphalt Paving
• Tar and Chip

Previous
Next
14
Website www.standardpavinginc.comPhone Number
844 266 7283physical address 8803
Sudley Road, Suite 206 Manassas, VA , USA

• How we can be found?

Previous