ECET 350 Technology levels--snaptutorial.com

1
ECET 350 Technology levels--snaptutorial.com
2
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 2 Homework For more classes
visit www.snaptutorial.com   Chapter 2, page
58-62, problems 2a, 2b, 2c, 7, 9a, 9b, 9c, 10a,
10b, 16a, 16b, 16c, 19, 21, 22a, 22b, 22c, 24.
3
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 2 iLab Signal Sampling and
Reconstruction For more classes
visit www.snaptutorial.com   Objectives Use
principles of signal sampling and reconstruction
to construct an electronic circuit to sample,
hold, and reconstruct the signal.
4
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 3 Homework For more classes
visit www.snaptutorial.com   Chapter 3 Homework
Problems 3a, 3b, 3c, 5a, 5c, 5e, 7a, 9
5
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 3 iLab Moving Average Digital
Filters For more classes visit www.snaptutorial.
com   Objectives Design, test, and implement
antialiasing and anti-imaging filters to be used
with a real-time, digital filtering system using
a microcontroller, ADC, and DAC.
6
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 4 Homework For more classes
visit www.snaptutorial.com   Chapter 9 Finite
Impulse Response Filters, pp. 314353
7
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 4 iLab Low-Pass Finite Impulse
Response Filter For more classes
visit www.snaptutorial.com   Objectives Design,
implement, test, and analyze the performance of a
finite impu
8
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 5 Homework For more classes
visit www.snaptutorial.com   Chapter 9 19.
Design a low pass FIR filter for a 10 kHz
sampling, with a pass band edge at 2 kHz, a stop
band edge at 3 kHz, and 20 dB stop band
attenuation. Find the impulse response and the
difference equation for the filter. 26. A high
pass filter with a pass band edge frequency of
5.5 kHz must be designed for a 16 kHz sampled
system. The stop band attenuation must be at
least 40 dB, and the transition width must be no
greater than 3.5 kHz. Write the difference
equation for the filter.
9
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 5 iLab Impulse Response Band Pass
Filter For more classes visit www.snaptutorial.c
om   Objectives Design a high-order, FIR band
pass using MATLAB and then to implement, test,
and analyze the real-time performance of that
filter on a target embedded system board. In
addition, introduce and compare the numerical
formats and processing requirements of digital
filters whe
10
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 6 Homework For more classes
visit www.snaptutorial.com   Chapter 10 Homework
Problems 12a, 12b  
11
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 6 iLab Infinite Impulse Response
Low-Pass Filter For more classes
visit www.snaptutorial.com   Objectives Design a
Butterworth, low-pass filter, and then, using a
bilinear transformation operation, create a
digital IIR filter. The filter will then be
implemented and real-time performance tested and
analyzed on a target embedded system board.
12
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 7 Homework For more classes
visit www.snaptutorial.com   ECET 350 Practice
Problems
13
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 7 iLab Fourier Analysis of Time
Domain Signals For more classes
visit www.snaptutorial.com   Objective of the lab
experiment The objective of this experiment is
to perform Fourier analysis to obtain frequency
domain signature of signals and systems that are
measured or whose characteristics
14
ECET 350 Technology levels--snaptutorial.com
ECET 350 Week 7 Homework For more classes
visit www.snaptutorial.com   ECET 350 Practice
Problems
15
ECET 350 Technology levels--snaptutorial.com