CIP Level 1 NACE-CIP1-001 questions

1
NACE-CIP1-001 dumps

• Coating Inspector Level 1

2
CIP Level 1 NACE-CIP1-001 Practice Questions

• 1. You are the NACE Inspector on a tank lining
  project where a 50 solids epoxy tank lining is
  being applied. After application of the 19 coat
  you notice small blisters in some areas of the
  applied lining.
• Your FIRST preferred course of action is to
• A. Break the blisters to see what's inside
• B. Document the problem and advise the Contractor
  and Owner's representative
• C. Document the problem and advise the Contractor
• D. Extract any liquid that may be inside the
  blister and send it to the lab for further
  analysis
• Answer B

Passcert.com
3
CIP Level 1 NACE-CIP1-001 Practice Questions

• 2. Dew point is the temperature at which
• A. water freezes.
• B. humidity decreases
• C. condensation occurs.
• D. the air is saturated.
• Answer C

Passcert.com
4
CIP Level 1 NACE-CIP1-001 Practice Questions

• 3. If a contractor is using a poorly maintained
  compressor to supply air for abrasive blast
  cleaning and conventional airspray, the coating
  inspector should perform a
• A. dry film thickness (DEI) measurement.
• B. wet film thickness (WFT) measurement.
• C. blotter test for the presence of oil and
  water.
• D. vial lest.
• Answer C

Passcert.com
5
CIP Level 1 NACE-CIP1-001 Practice Questions

• 4. Upon arrival of coating materials, the
  inspector should
• A. review coating contractors' plans for storage
  of coating materials and confirm they meet
  national, local and owners' fire and
  environmental regulations.
• B. observe and document the amount of material
  and batch numbers.
• C. observe aryl document that the applicator WFT
  at regular intervals during application.
• D. observe and document time frame and
  environmental conditions between each coat.
• Answer B

Passcert.com
6
CIP Level 1 NACE-CIP1-001 Practice Questions

• 5. Relative humidity is
• A. a measure of the amount of moisture in the air
  compared to saturation level.
• B. a measure of the amount of moisture in the air
  compared to the air temperature.
• C. the lowest temperature at which moisture forms
  on a steel surface.
• D. the highest temperature at which moisture
  forms on a steel surface.
• Answer A

Passcert.com
7
CIP Level 1 NACE-CIP1-001 Practice Questions

• 6. Galvanic corrosion occurs on which of the
  following substrates
• A. Concrete
• B. Fiberglass Reinforced Plastic
• C. Metal
• D. Wood
• Answer C

Passcert.com
8
CIP Level 1 NACE-CIP1-001 Practice Questions

• 7. When applying Thermal Spray Coatings the
  specification is most likely to refence
• A. SSPC PA 2
• B. NACE SP 0178
• C. NACE SP 0188
• D. SSPC-CS 23.00/AWS C2.23/NACE No. 12
• Answer D

Passcert.com
9
CIP Level 1 NACE-CIP1-001 Practice Questions

• 8. What is the minimum recommended distance away
  from an edge that an inspector should take a
  measurement with a dial-type magnetic pull-off
  Dry Film Thickness (DFT) gauge?
• A. 1 cm (.39 inch)
• B. 2.5 cm (1 inch)
• C. 6.35 cm (2.5 inch)
• D. 2.5 millimeters (.10 inch)
• Answer B

Passcert.com
10
Why choose Passcert dumps?

• Questions collected from real test
• One year free update
• Money back guarantee
• Send both pdf and software(free)
• Lower price
• https//www.passcert.com/NACE-CIP1-001.html