ECET 365 Seek Your Dream /newtonhelp.com

1
ECET 365 Your Dreams Our Mission/newtonhelp.com
2
ECET 365 Entire Course (All Labs and Quizzes) 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
•  
• ECET 365 Lab 1 Using the Serial Communication
  Interface in a Microcontroller
• ECET 365 Lab 2 Temperature Measuring System using
  a Microcontroller
• ECET 365 Lab 3 Traffic Light Control Using Finite
  State Machines (FSM)
• ECET 365 Lab 4 Servo Control Using Pulse Width
  Modulation (PWM)
• ECET 365 Lab 5 Servo Motor Interfaces-Closed-Loop
  Motor Speed Control
• ECET 365 Lab 6 Servo Motor Interfaces-Closed-Loop
  Motor Speed Control

3
ECET 365 Lab 1 Using the Serial Communication
Interface in a Microcontroller 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Lab 1 of 6 Using the Serial Communication
  Interface in a Microcontroller
• Submit your assignment to the Dropbox located on
  the silver tab at the top of this page.
• (See Syllabus section Due Dates for Assignments
  Exams for due dates.)

4
ECET 365 Lab 2 Temperature Measuring System using
a Microcontroller 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Lab 2 of 6 Temperature Measuring System using a
  Microcontroller
• Submit your assignment to the Dropbox located
  under the silver tab at the top of this page.
• (See Syllabus section Due Dates for Assignments
  Exams for due dates.)
• L A B O V E R V I E W
• Scenario/Summary

5
ECET 365 Lab 3 Traffic Light Control Using Finite
State Machines (FSM) 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Lab 3 of 6 Traffic Light Control Using Finite
  State Machines (FSM)
• Submit your assignment to the Dropbox located
  under the silver tab at the top of this page.
• See Syllabus section Due Dates for Assignments
  Exams for due dates.
• L A B O V E R V I E W

6
ECET 365 Lab 4 Servo Control Using Pulse Width
Modulation (PWM)

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Lab 4 of 6 Servo Control Using Pulse Width
  Modulation (PWM)
• Submit your assignment to the Dropbox located
  under the silver tab at the top of this page.
• (See Syllabus section Due Dates for Assignments
  Exams for due dates.)
• L A B O V E R V I E W

7
ECET 365 Lab 5 Servo Motor Interfaces-Closed-Loop
Motor Speed Control 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Lab 5 of 6 Servo Motor Interfaces-Closed-Loop
  Motor Speed Control
• Submit your assignment to the Dropbox located
  under the silver tab at the top of this page.
• (See Syllabus section Due Dates for Assignments
  Exams for due dates.)
• L A B O V E R V I E W

8
ECET 365 Lab 6 Servo Motor Interfaces-Closed-Loop
Motor Speed Control 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Lab 6 of 6 Servo Motor Interfaces-Closed-Loop
  Motor Speed Control
• Submit your assignment to the Dropbox located
  under the silver tab at the top of this page.
• See Syllabus section Due Dates for Assignments
  Exams for due dates.
• L A B O V E R V I E W

9
ECET 365 Week 1 Homework Problems 8.9, 8.10,
D8.1, D8.14 ,D8.15 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Page 454-455
• Problems 8.9, 8.10, D8.13, D8.14, D8.15
• 8.9) A stepper motor has 24 north teeth and 24
  south teeth. What angle change occurs on each
  step?
• If a full step is output every 1 ms (and assuming
  it doesnt slip), at what speed does the motor
  spin?
• 8.10) Draw a figure similar to figure 8.80
  showing how half stepping works.

10
ECET 365 Week 1 iLab Motor Control 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Objectives
• A. Develop software routines that control Stepper
  Motors, small permanent magnet DC motors, and
  Servos.
• B. Understand how an H-bridge can be used to
  control DC motors and Stepper Motors.
• Questions for the DC Motor Procedures

11
ECET 365 Week 1 Quiz

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Question 1. Question (TCO 3) To allow a relay
  coil current of 150 mA through an NPN transistor
  with a gain (beta) of 75, the current through the
  base must be _____.
• Question 2. Question (TCO 3) A stepper motor
  requires 250 steps per revolution. How many
  degrees does the motor rotate per step?
•  

12
ECET 365 Week 2 Homework Problems 7.1, 7.4 ,7.9,
7.13 ,D7.17 and 12.1, 12.5 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• ECET 365 Week 2 Homework Problems
• Pages 384 387, Problems 7.1, 7.4, 7.9, 7.13,
  D7.17.
• Page 639, Problems 12.1 12.5.

13
ECET 365 Week 2 iLab Interfacing to the Smart Car
Video Sensor 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Objectives
• Develop a hardware interface to the TSL1401 Video
  Sensor in the Smart Car Kit.
• Test the sensor with software and use data to
  control the steering servo.
• (Mini Project) Use mini lab TTL pulser to
  simulate the sensor inputs and control PWM output
  on/off so as to test your motors steering system.
  or less.

14
ECET 365 Week 2 Quiz 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• 1. Question (TCO 5) Identify the step
  size for an 8-bit analog-to-digital converter
  with Vref 2.5 VDC?
•  
• Student Answer 10 millivolts
• 25 millivolts
• 4.9 millivolts
• 5 volts
•  

15
ECET 365 Week 3 Homework Problems 2.18 2.19 2.20
D2.23 D2.24 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• ECET 365 Week 3 Homework
• Pages 146 - 147, Problems 2.18, 2.19, 2.20,
  D2.23, D2.24
• 2.18 In 32 words or less, describe the
  meaning of each of the following terms.
• 19. Give a quantitative measure of
  modularity (e.g., System A is more modular than
  system B) if

16
ECET 365 Week 3 iLab Converting Requirements to a
Work Schedule 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• ECET 365 Week 3 iLab Converting Requirements to a
  Work Schedule
• Objectives
• A. Develop a map showing which hardware
  subsystems from the kit will be used to meet each
  requirement. Determine if additional parts are
  required.

17
ECET 365 Week 3 Quiz 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• 1. Question (TCO 3) Which interrupt is
  non-maskable?
•  
• Student Answer Software interrupt (SWI)
• Interrupt from a device connected to IRQ pin
  of HCS12 microcontroller
• Both A and B
• Interrupt by multiple devices connected to
  IRQ pin of HCS12 microcontroller
•  

18
ECET 365 Week 4 Homework Problems 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Answer Pages 242, Problem 4.10 page 586,
  problems 11.5c, g and page 589, problems D11.20,
  D11.21.
• Page 242, Problem 4.10 What purpose might there
  be to use the PLL and slow down the 9S12?
• Page 586, Problem 11.5 c) g) For each pair of
  terms, explain the similarities and differences
  in 32 words or less.

19
ECET 365 Week 4 iLab System and Subsystem Power
Supplies 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• ECET 365 Week 4 iLab System and Subsystem Power
  Supplies
• Objectives
• A. Test the main power supply of the Robotic Car
  or robotic system.
• B. Test the subsystem power supplies and
  determine if a separate battery system is
  required for the subsystems.

20
ECET 365 Week 4 Quiz 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• . Question (TCO 1, 2, and 7) Select
  the header file in CodeWarrior for the Freescale
  MC9s12DG256.
•  
• Student Answer mc9s12dg256.h
• mc9s12dg256.header
• mc9s12dg256.asm
• mc9s12dg256

21
ECET 365 Week 5 Homework 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• ECET 365 Week 5 Homework
• Page 241, Problems 4.14.9
• 4.1Syntactically, I/O ports are public globals.
  In order to separate mechanisms from policies
  (i.e., improve the quality of the software
  system), how should I/O be actually used?

22
ECET 365 Week 5 iLab Timing and Interrupts 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Objectives
• A. Determine the timing requirements for data to
  and from subsystems.
• B. Change a procedural subroutine to an
  interrupt-driven subroutine.
• C. Compare the interrupt-driven system operation
  to the procedural system.
• Step 1 Procedure

23
ECET 365 Week 5 Quiz

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• . Question (TCO 5) In an asynchronous
  data transfer _____.
•  
• Student Answer the transmitter and
  receiver clock must be exactly the same all the
  time
• the receiver clock must be exactly the same
  or multiple times the transmitter clock
• it is not necessary to have a clock in the
  receiver

24
ECET 365 Week 6 Homework Problems 14.1,14.4 ,14.8
,14.13 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• ECET 365 Week 6 Homework
• Page 710 Problems 14.114.4, 14.814.13
• 14.1 For each term, give a definition in 32 words
  or less.
• a) Master-slave

25
ECET 365 Week 6 iLab Interfacing to Networks 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Objectives
• A. Compare characteristics of different wireless
  communications modules.
• B. Compare characteristics of different wireless
  Internet communications modules.
• C. Determine which modules are the most suitable
  for the Smart Car or Robotics project.

26
ECET 365 Week 6 Quiz 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• . Question (TCO 6) How many 16-bit PWM
  channels are available in the Freescale 9S12DG256
  microcontroller?
•  
• Student Answer Two
• Four
• Seven
• Eight

27
ECET 365 Week 7 Homework Problems 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Pages 384387, Problems 7.1, 7.4, 7.9, 7.13,
  D7.17
• Page 639, Problems 12.112.5
• Chapter 7
• 7.1.) For each term, give a definition in 32
  words or less.
• 7.4.) Look up in the 9S12 data sheet how the SCI
  checks for noise. In particular, when is the
  noise flag set? How does software clear the noise
  flag?

28
ECET 365 Week 7 iLab Integration of Subsystems 

• For more course tutorials visit
• uophelp.com is now newtonhelp.com
• www.newtonhelp.com
• Objectives-
• Complete the assembly of project subsystems.
• Test the operation of the completed project.
• Observations/Measurements
• A. Visual Subsystem

29
ECET 365 Your Dreams Our Mission/newtonhelp.com