ECET 402 Help Bcome Exceptional / snaptutorial.com

1
ECET 402 Help Bcome Exceptional / snaptutorial.com
2
(No Transcript)
3
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 1 Homework  
ECET 402  HW Week 1 Pages 20-21 2,4,6,11,14 CH
3pgs103 4,6
4
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 1 iLab  
1.From Part A, step 1(b) of lab instructions,
change the temperature from 0 to 30 C and record
the corresponding RTD resistance in Table
1. 2.Graph the temperature-resistance
characteristics of RTD below 3.Is the graph
obtained in step 2 above linear (a straight
line)? 4.Use the graph obtained in step 2 above
to determine the resistance of RTD at 75 F.
5
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 2 Homework  
Chapter 3 Page 104-105 Problems 24, 25, 28, 30,
and 38
6
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 2 iLab  
1.After completing Part A of week 2 lab, complete
the following table 2.Briefly describe if you
had any issues with this lab. 3.Briefly describe
how you would display the temperature on the LCD
display of a microcontroller system. 4.From Part
B, step 1 of lab instructions, paste your
Multisim circuit design below. 5.From Part B,
step 2 of lab instructions, paste your Multisim
circuit design below.
7
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 3 Homework  
Homework 1. What is the difference between
static,sliding, and viscous friction? 2. An
aluminum casting that weighs 10 lb is resting on
a steel surface. 6.A robot arm must be able to
extend 24 in. horizontally in 2 s while carrying
a load of 10 lb. How much force is required,
assuming the arm is accelerating all the way?
8
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 3 iLab  
Part A Voltage to Frequency Converter 1.Change
input voltage from 210 volts and record measured
frequency in Table 1 2. Use the data obtained in
Table 1 to graph Frequency vs. Voltage in Figure
1. 3.Is the output frequency vs. voltage graph
linear?
9
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 4 Homework    
Week 4 Homework Chapter 11 pp. 483488, Problems
1, 2, 6, 8, 12, 13, and 19 1.Assume that Figure
11.25(a) is the response curve of a control
system to a step function. Determine the
following parameters rise time, overshoot, and
settling time.
10
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 4 iLab Relays and Relay Logic
Controls  
ECET 402 Week 4 iLab Relays and Relay Logic
Controls
11
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 5 Homework    
Chapter 12 1. Draw a relay wiring diagram for a
circuit that implements the simple logic diagram
shown in Figure 12.36. The circuit should be in
the style of Figure 12.1(a). 2. Repeat Exercise 1
except draw the circuit as a ladder diagram.
12
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 5 iLab PLC Programming with
LogixPro  
Introduction The requirements for a motor with a
temperature sensor are that the motor must be
turned on with a Push Button switch, and also
turned off with a push button switch. If at any
time the temperature is too hot, the motor must
turn off no matter what push buttons are pressed.
13
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 5 iLab Stepper Motor and Measuring
Speed of a DC Motor  
Part A  Take a digital photo of your stepper
motor circuit and paste it below Once the
assembly of stepper motor circuit is completed
and power is applied, observe the direction of
rotation and record it here
14
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 6 Homework  
P.405, 1Give an example of an open-loop control
system. Explain why the system is open-loop, and
identify the controller and final control
element. P.405, 2Give an example of a
closed-loop control system. Explain why the
system is closed-loop, and identify the sensor,
controller, and final control element. P.405,
7Describe the advantages of a 4- to 20-mA
current loop as an input signal compared to a
0-to 5-V input signal. P.435, 2Complete a report
on one type of open communications network.
15
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 6 iLab  
1. Determine the overall transfer function of the
system given below by hand as discussed in
pre-lab. Please show your work and type the
equations if you can 2. Determine the overall
transfer function of the system shown above using
MATLAB. Copy the MATLAB code and the overall
transfer function obtained and paste them below
16
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 7 iLab Root Locus Plots and the
Stability of a Control System  
ECET 402 Week 7 iLab Root Locus Plots and the
Stability of a Control System
17
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 7 iLab
ECET 402 Week 7 iLab
18
ECET 402 Help Bcome Exceptional / snaptutorial.com
ECET 402 Week 7 You Decide Assignment    
ECET 402 Week 7 You Decide Assignment
19
(No Transcript)
20
ECET 402 Help Bcome Exceptional / snaptutorial.com