How to refinishing hardwood floors

1
How to Refinishing Hardwood Floors?

• HardWood Floor Refinishing

2

• If youve got done tiny sanding comes, a trifle
  little bit of trade its time for next step and
  refinishing hardwood floors. I like to recommend
  to start out with one tiny sleeping room, do not
  begin within the corridor or whole house. Sanding
  wooden flooring may be a time overwhelming
  project and its higher to find out on the little
  sleeping room.

3
Tools You Will Need

• 1. Good dirt masks. Rent an honest tools that
  have dustless refinishing system.
• 2. Main electric sander, this could be a sander
  electric power tool or belt sander.
• 3. Edger that is to surface the sides, near the
  wall.
• 4. Buffer for the ultimate sleek sanding of you
  hardwood floors.

4

• 5. Sand paper for every machine. For a little
  sleeping room get 40 grit sixty grit eighty grit
  100 grit for the most electric sander, get just
  one of every grit, for the edger identical grits
  however youll would like five discs of every
  grit. If the provider is shut youll be able to
  forever get a lot of if you wish it, the
  utilization of the sandpaper depends on the end
  that has been used on the hardwood floors. Some
  hardwood floors are painted. If youd wish to
  surface painted hardwood floor confirm you get
  lots of paper. its not suggested to sand paint
  since most of the paints can cause metastasis
  issues once sanded.
• 6. One 150 buffer screen and one 180 buffer
  screen.
• 7. Vacuum
• 8. Sealer, finish, brush and end applier.
• You can rent those tools and also the native
  rental tools place. In Victoria, BC particularly
  youll be able to notice couple places in
  telephone book.

5
Refinishing Process

• Vacuum the area initial.
• 2. You will use the most electric sander initial
  mistreatment forty grit, confirm to sand wooden
  flooring with the grain(run the sanding machine
  identical direction that boards run)
• 3. Make sure youre sanding steady, do not stop
  with the electric sander operating.
• 4. Main electric sander wont get near the walls,
  this can be wherever youve got to use edger. Use
  identical grit that is 40.You can take of the
  baseboards and install them back when the eating
  is finished. If you do not need to put in
  baseboards you can need to be terribly careful to
  not bit baseboards with the edger and so will
  need to manually scrape the unhanded space near
  the baseboards

6

• 5. Sand with main electric sander with 60 grit
  afterward edger once more with 60 grit.
• 6. Repeat the method mistreatment the 80 grit.
• 7. Reset the nails
• 8. Vacuum the ground very well. Apply the wood
  filler with an out sized spatula.
• 9. Wait associate till wood filler is dry. Drying
  time are completely different relying wherever
  youre, after all in hot climate like Victoria,
  Vancouver at the new sunny day when one hour
  filler is dry and wooden flooring able to sand
  once more.
• 10. Sand off the filler with 100 grit. If the
  filler failed to came off fully when one cut,
  sand floors an additional time.

7

• Sand with edger near the wall mistreatment
  100grit.
• 12. Vacuum sanded hardwood floor well. confirm at
  this time to stay the ground dry and clean.
• 13. Using buffer sand with 150 grit.
• 14. Vacuum once more and sand with 180 grit.
• 15. Vacuum once more very well.
• 16. Apply hardwood floor sealer wait till dry.
• 17. Apply two coats of end, follow manufacturer
  directions.
• This is an easy means of refinishing hardwood
  floors.

8
TDI HardWood Floors

• Address 2845 Acacia Drive,Victoria, B.C. ,V9B
  5A2, Canada
• Telephone [phone]
• Cell 250-884-7409
• Email Id info_at_tdihardwoodfloors.com
• Website http//www.tdihardwoodfloors.com

9
(No Transcript)