How To Choose A CNC Cutting Machine

1
How To Choose a CNC Cutting Machine
2
Cutting Breadth

• To select a CNC cutting machine more suitable, we
  must consider the following factors the width of
  the cutting structure, the height adjustment mode
  cutoff mode. They burner may also be mounted
  together on request.
• Cutting width refers to the width and length of
  the effective cutting.

3
Cutting Breadth

• 1) Take portable type as example, when our
  machine is installed on the plate should be
  considered Teo aspects a, the size of the
  workpiece, you should make sure that the machine
  can cut in an hour b, width of plate. When
  machine is placed on the plate, effective cutting
  width should be as long as plate width, in order
  to reduce the frequent movement our portable
  cutting.

4
Cutting Breadth

• 2) On the other type which is the same, reducing
  the width of our machine is dependent on the
  characteristics of the plate to be cut. You must
  make sure that the machine can cut the workpiece
  during time. Otherwise, it is not convenient to
  move our machine time and again. For gantry
  structure, to improve efficiency, you can put two
  plates in the longitudinal direction or in the
  transverse direction at the same time.

5
Structure

• We have a portable, cantilever, gantry and table
  type.
• Portable console and type easy to transport and
  install, compact, low cost. But effective width
  of the cut is limited.
• Gantry type, good rigidity, cutting width can be
  up to 3-10m. But that need high requirements for
  precision and special plant installation area.
• Table type is an integral part of the structure,
  with a fast and accurate placement, but the
  extent of the cut is limited.

6
Cutting Mode

• Cutting mode can be classified from different
  perspectives
• Flame cutting, plasma cutting, two flame and
  plasma cutting
• Dry type plasma cutting and Under water plasma
  cutting
• CNC and Strip Cutting Machine (Linear cutting
  machine)
• CNC intersection cutting (cutting pipe).

7
Torch Height adjusting mode

• Regardless of the fact that the flame or plasma
  cutting, all that we need to ensure that the
  distance between the torch and the plate is most
  suitable for the best cut quality and extend the
  life of the cutting nozzle.
• Torch height setting mode
• 1). Manual adjustment
• the wheel via the driving gear rack torch to
  adjust the height of the torch.

8
Torch Height adjusting mode

• 2). Electric adjusting
• Click through the motor controller drive torch up
  and down.
• The above statement, so you need to adjust the
  height of the torch.

9
Torch Height adjusting mode

• 3). Capacitive height controller for flame
  cutting
• On the one hand, this device can automatically
  adjust the height of the torch to maintain a
  constant height On the other hand, after
  preheating, when we open the high pressure
  cutting oxygen, there will be slag spatter. Thus
  it is easy to jam cutting nozzle. With the device
  before opening the high-pressure oxygen, torch is
  mounted in advance. After slag splashing down the
  torch itself, so that avoid nozzle jam.

10
Torch Height adjusting mode

• 4). Arc voltage height controller for plasma
  cutting
• On the one hand, speed of plasma cutting very
  quickly, on the other hand, the plasma arc is
  very dazzling. As consequence, if traders are
  watching the distance between the cutting torch
  and the plate, at all times, they can not catch
  up with the cutting speed and your eyes can not
  see for the plasma arc long time. This still
  difficult, if the plate is very thin. So, which
  usually set the device by using plasma cutting.
• If you are looking to buy CNC cutting machine in
  myanmar, visits at baganmart.com, which is
  myanmar B2B e-commerce platform and online
  shopping for myanmar business products buyers.

11
Thanks For Watching

• www.baganmart.com
• www.facebook.com/baganmart
• www.twitter.com/_at_BaganBlog