Title: Therapeutic Ultrasound
1Therapeutic Ultrasound
- Jennifer Doherty-Restrepo, MS, LAT, ATC
- Entry-Level ATEP
- Therapeutic Modalities
2Therapeutic Ultrasound
- One of the most widely used modalities in sports
medicine - _______________ inaudible, acoustic vibrations
of high frequency that produce either thermal or
non-thermal physiologic effects
3Transmission of Acoustical Energy in Biological
Tissue
- Relies on _______________ for transmission
- Collisions cause molecular displacement and a
wave of _______________ - Acoustic energy does ______ travel readily
through space - Must travel through a _______________
- Acoustic energy does not travel in a
_______________ - Travels in waves in all directions
- Longitudinal and transverse waves
4Longitudinal Waves
- Primary waveform for travel in soft tissue
- Molecular displacement occurs along the
______________________________
5Transverse Waves
- Primary waveform for travel in ______
- Molecular displacement is _______________ to
direction of wave propagation -
6Frequency Of Wave Transmission
- Audible sound _______________ Ultrasound gt
_______________ - Therapeutic Ultrasound _______________
(1,000,000 cycles/sec) - Penetration and absorption are ____________
related - Lower frequencies ______ depth of penetration
- Higher frequencies superficial ______________
7Velocity Of Transmission
- Directly related to tissue ______ (conducting
medium) - Higher density ______ velocity of transmission
- Lower density ______ velocity of transmission
- At a frequency of 1 MHz, ultrasound travels
through - Soft tissue at _______________
- Bone at _______________
8Attenuation
- _______ in energy intensity as the ultrasound
wave is transmitted through various tissues - ________ is due to absorption, dispersion, or
scattering, which result from __________ and
__________
9Penetration vs. Absorption
- _______________ relationship
- Absorption increases as frequency __________
- Tissues high in water content _________
absorption - Blood
- Tissues high in protein content ________
absorption - Bone, nerves, muscles, and fat
10Ultrasound at Tissue Interfaces
- Some acoustic energy scatters due to reflection
and refraction - ____________________ determines the amount
energy reflected or transmitted at tissue
interfaces - _______________ X _______________
- If the acoustic impedance is equal at the tissue
interface, energy will be _______________ - The larger the difference in acoustic impedance
at the tissue interface, the more energy is
_______________
11Acoustic Impedance
- Transducer - Air interface energy is completely
_______________ - Through fat energy is transmitted
- _________________ energy is reflected and
refracted - Soft tissue - Bone interface energy is
_______________ - Creates standing waves or hot spots
12Therapeutic Ultrasound Generators
- High frequency electrical generator connected
through an oscillator circuit and a transformer
via a coaxial cable to a transducer housed within
an insulated applicator
13Ultrasound Generator
Electrical Output Mechanical Vibration Acoustic
Soundwave Absorbed In The Tissues
14Therapeutic Ultrasound Generator Control Panel
- Timer
- Power meter
- Intensity control
- _______________
- Duty cycle switch
- _______________
- Selector switch for continuous or pulsed
- Automatic shutoff if transducer overheats
15Transducer
- AKA
- _______________, or
- _______________
- Not interchangeable
- Piezoelectric crystal
- Quartz
- Synthetic ceramic crystal
- Converts ____________ energy to _____ energy
through mechanical deformation
16Piezoelectric Effect
- When an alternating current generated at the same
frequency as the crystal resonance is passed
through the peizoelectric crystal, it will
________ and _______________
- Direct Effect - An electrical voltage is
generated when the crystal expands and compresses
17Piezoelectric Effect
- ____________ generation of electrical voltage
across the crystal when it is expanded or
compressed - __________________________ the alternating
current moving through the crystal reverses its
_______ as it expands and compresses resulting in
vibration of the crystal at the frequency of the
electrical oscillation - This produces the desired therapeutic ultrasound
frequency
18Effective Radiating Area (ERA)
- The portion of the transducer surface that
actually produces the _______________ - Dependent on the __________ of the crystal
- Ideally, the surface area of the crystal nearly
matches the diameter of the transducer surface - Acoustic energy is contained in a ________
___________ beam that is roughly the same
diameter of the transducer
19Frequency of Therapeutic Ultrasound
- Frequency number of wave cycles completed each
_______________ - Frequency range of therapeutic ultrasound is
_______________ - Most generators produce either 1.0 or 3.0 MHz
20Frequency of Therapeutic Ultrasound
- Depth of penetration is __________________ not
intensity dependent - 1 MHz deep heat
- _______________
- 3 MHz superficial heat
- _______________
21The Ultrasound Beam
- Concentrates energy in a limited area
- Larger transducer more ____________ _________
beam - Smaller transducer more _________ beam
- 1 MHz frequency more divergent than 3 MHz
frequency
22Ultrasound Beam
- Near field
- Distribution of energy is _______________
- Area near transducer
- Non-uniformity due to differences in acoustic
pressure created by the waves emitted from the
transducer
23Ultrasound Beam
- Point of Maximum Acoustic Intensity
- As acoustic waves move ________ from transducer,
they become indistinguishable and arrive at a
certain point simultaneously
24Ultrasound Beam
- Far Field
- Waves travel beyond the point of maximum acoustic
intensity - Energy is more _____ ___________ and the beam
becomes more divergent
25Beam Nonuniformity Ratio (BNR)
- Indicates the amount of ______________ in
intensity within the ultrasound beam - Determined by the highest intensity found in the
ultrasound beam relative to the average intensity
across the transducer - Ideal BNR would be _______________
- Typical BNR _______________
- Maximal point of intensity 6 W/cm2
- Average output of intensity across transducer 1
W/cm2
26Beam Nonuniformity Ratio (BNR)
- _____________ more even the intensity
- Less risk of developing hot spots
- _______________ higher nonuniformity
- Must move transducer faster throughout treatment
to avoid hot spots - Manufacturers must report the BNR
- Better generators have a ______ BNR, thus
providing more even intensity throughout the field
27Pulsed vs. Continuous Ultrasound
- Continuous Ultrasound
- Ultrasound intensity remains constant over time
- Ultrasound energy produced ________ of the time
28Pulsed vs. Continuous Ultrasound
- Pulsed
- Ultrasound intensity is interrupted with no
energy produced during the off time - Average intensity of output over time is _________
29Pulsed Ultrasound and Duty Cycle
- Duty Cycle
- Percentage of time that ultrasound is being
generated (pulse duration) over one pulse period - Pulse period markspace ratio
- Duty Cycle duration of pulse (on time)
x100 pulse
period (on time off time) - Duty Cycle may be set to 20 or 50
- Total amount of energy delivered would be only
20 or 50 of the energy delivered if a
continuous ultrasound wave was being used
30Amplitude
- May be defined 3 ways
- Magnitude of vibration in an ultrasound wave
- Movement of particles in the medium through which
the ultrasound wave travels - Measured in units of distance (____________)
- Vibration in pressure found along the ultrasound
wave - Measured in units of pressure (______________)
31Power vs. Intensity
- Both power and intensity are unevenly distributed
in the ultrasound beam - ______ total amount of ultrasound energy in the
beam - Measured in watts
- _______ measure of the rate at which energy is
being delivered per unit area
32Intensity
- Spatial Average Intensity intensity of
ultrasound beam averaged over the ______
_______________ - Measured in W/cm2
- Power output in watts ERA of
transducer in cm2 - Example
- 6 watts 1.5 W/cm2 4 cm2
33Intensity
- Spatial Peak Intensity _________ value
occurring with the beam over time - Therapeutic ultrasound maximum intensities range
between ___ and ___ W/cm2 - Temporal Peak Intensity __________ intensity
during the __ period with pulsed ultrasound - Measured in W/cm2
34Intensity
- Temporal-averaged Intensity
- Only important with ___________ ultrasound
- Calculated by averaging the power during both the
on and off periods (mean on/off intensity) - Intensity settings on ultrasound generators may
indicate _________________________ while others
indicate ______________________
35Intensity
- There are no specific guidelines which dictate
specific intensities that should be used during
treatment - Recommendation use the _______ intensity at the
_________ frequency which transmits energy to a
specific tissue to achieve a desired therapeutic
effect - Any adjustment in the intensity must be countered
with an adjustment in _______________ - Treatments are temperature dependent, not time
dependent
36Physiologic Effects of Ultrasound
37Thermal vs. Non-Thermal Effects
- Thermal effects
- Tissue heating
- Non-Thermal effects
- Tissue repair at the cellular level
- Thermal effects occur whenever the spatial
average intensity is gt _______________ - Whenever there is a thermal effect there will
always be a non-thermal effect
38Thermal vs. Non-Thermal Effects
- To elicit thermal therapeutic effects, tissue
temperature must be raised to a level of 40-45C
for a minimum of ___ minutes - Baseline muscle temperature is _________
- Mild heating temperature ? of _____
- ? metabolism healing and healing
- Moderate heating temperature ? of ______
- ? pain and muscle spasm
- Vigorous heating temperature ? of ____
- ? extensibility of collagen and ? joint stiffness
39Thermal Effects of Ultrasound
- Increased collagen extensibility
- ________ blood flow
- ________ pain
- Reduction of muscle spasm
- ________ joint stiffness
- Reduction of _______________
40 Ultrasound Rate of Heating Per Minute
Intensity W/cm2 1MHz 3MHz
0.5 .04C .3C 1.0
.2C .6C 1.5 .3C
.9C 2.0 .4C
1.4C
- At an intensity of 1.5 W/cm2 with a frequency of
1MHz, an ultrasound treatment would require a
minimum of 10 minutes to reach vigorous heating
41 Ultrasound Rate of Heating Per Minute
Intensity W/cm2 1MHz 3MHz
0.5 .04C .3C 1.0
.2C .6C 1.5 .3C
.9C 2.0 .4C
1.4C
- At an intensity of 1.5 W/cm2 with a frequency of
3 MHz, an ultrasound treatment would require only
slightly more than 3 minutes to reach vigorous
heating
42Non-Thermal Effects of Ultrasound
- ________ fibroblastic activity
- ________ protein synthesis
- Tissue _______________
- Reduction of __________
- Bone healing
- Pain modulation
All of these Non-Thermal Physiologic Effects of
Ultrasound Occur Through Acoustic Microstreaming
and/or Cavitation
43Acoustic Microstreaming
- Unidirectional flow of fluids along the cell
membrane interface resulting from mechanical
pressure waves in an ultrasonic field - Alters cell membrane permeability to ______ and
________ ions important in the healing process
44Cavitation
- Formation of gas-filled bubbles that expand and
compress due to ultrasonically induced pressure
changes in tissue fluids
45Cavitation
- _______________
- Results in an increased fluid flow around these
bubbles - _______________
- Results in violent large excursions in bubble
volume with collapse creating increased pressure
and temperatures that can cause tissue damage
Therapeutic benefits are derived only from stable
cavitation
46Non-Thermal Effects of Ultrasound
- Can be maximized while minimizing the thermal
effects by - Using a ____________________ of
0.1-0.2 W/cm2 with continuous ultrasound - Setting duty cycle at ________ at intensity of
1 W/cm2 - Setting duty cycle at ________ at intensity of
0.4 W/cm2
47Techniques of Application
48Frequency of Treatment
- Acute conditions require more frequent treatments
over a _________ period of time - 2 treatments/day for _______ days
- Chronic conditions require fewer treatments over
a _______ period of time - Alternating days for ________ treatments
- Controversy
- Limit treatments to a total of 14
- Continue treatments if there is improvement
49Duration of Treatment
- Considerations for determining Tx time
- Size of the area to be treated
- Intensity of treatment
- Frequency
- Treatment goals
- Thermal vs. non-thermal effects
50Size of the Treatment Area
- Should be ___ times larger than the ERA of the
crystal in the transducer - If the treatment area is larger than 2-3 times
the ERA, other modalities should be considered - _______________, _______________, or
_______________
51Intensity
- Recommendations for specific intensities make
little sense - Ultrasound intensity should be adjusted to
_______ ____________ - Increase intensity to the point where the patient
feels _______, then decrease the intensity
slightly to elicit general heating in the
treatment area - If you decrease intensity during treatment you
should increase _______________ - Ultrasound treatments should be temperature
dependent, not time dependent
52Frequency
- Determines _______________
- Determines _______________
- Energy produced at 3 MHz is absorbed 3 times
faster than that produced from 1 MHz ultrasound - Results in faster heating
- Reduce 3 MHz treatment durations by _________
53(No Transcript)
54Coupling Methods
- Greatest amount of energy reflection occurs at
the _______________ - Reduce amount of energy reflection by holding
transducer ____________ (90 angle) to treatment
area - Coupling mediums further _________ reflection
- _______________ substance used to decrease
acoustical impedance at the air-tissue interface - Maximize contact with the tissue to facilitate
passage of ultrasound energy - Include gel, water, mineral oil, distilled water,
glycerin, analgesic creams
55Direct Contact
- Transducer should be small enough to treat the
injured area - Gel should be applied liberally
- Heating gel does not increase the effectiveness
of the treatment
56Immersion Technique
- Good for treating irregular surfaces
- A plastic, ceramic, or rubber basin
should be used - Tap water is useful as a coupling medium
- Transducer should move ______ to the surface at a
distance of _________cm from the treatment area - Air bubbles should be wiped away
57Bladder technique
- Good for treating irregular surfaces
- Uses a balloon filled with water
- Both sides of the balloon should be liberally
coated with a _______________
58Moving The Transducer
- Applicator should be moved at a rate of
_______________ - An ultrasound generator with a low BNR allows for
________ transducer movement - An ultrasound generator with a high BNR may cause
unstable ___________ and hot spots if the
transducer is moved ______ _________
59Clinical Applications For Ultrasound
- Ultrasound is recognized clinically as an
effective and widely used modality in the
treatment of soft tissue and boney lesions - There is relatively little documented, data-based
evidence concerning its efficacy - Most of the available data-based research is
unequivocal
60Soft Tissue Healing and Repair
- During the __________________________ of healing,
stable cavitation and _______________ increase
the transport of calcium across cell membranes,
thus releasing histamine - Histamine stimulates
- ___________ to clean up the injured area
- ___________ to produce collagen (Dyson, 1985,
1987)
61Scar Tissue and Joint Contracture
- Increased tissue temperature causes an increase
in elasticity and a ___________ in viscocity of
collagen fibers (Ziskin, 1984) - Increased tissue temperature ___________ mobility
in mature scar tissue (Gann, 1991)
62Chronic Inflammation
- Few clinical or experimental studies have
observed the effects of ultrasound treatment on
chronic inflammation - Ultrasound does seem to be effective for
increasing blood flow to the treatment area,
which may facilitate the healing process and
reduce pain (Downing, 1986)
63Bone Healing
- Ultrasound ___________ fracture repair
- (Dyson, 1982, Pilla et al., 1990)
- Ultrasound given to an __________ fracture during
cartilage formation may cause cartilage
proliferation and delay union - (Dyson, 1989)
- No effect on _______________, but may help reduce
surrounding inflammation - (Ziskin, 1990)
- Not effective in detecting _______________
64Pain Reduction
- Ultrasound treatments are not used specifically
for pain modulation - Ultrasound may increase the ___________
____________ of free nerve endings - (McDiarmid, 1987)
- Superficial heating may effect gating of pain
impulses - _______________ - (Williams et al. 1987)
- Increased nerve conduction velocity creates a
_______________ effect - (Kitchen, 1990)
65Placebo Effects
- A number of studies have demonstrated a placebo
effect in patients using ultrasound - (Lundeberg, 1988, Dyson, 1987, Hashish et al.,
1986)
66Phonophoresis
- Ultrasound energy used to drive topical
application of selected medications into the
tissues - _______________
- Cortisol
- Salicylates
- Dexamethasone
- _______________
- Lidocaine
67Phonophoresis
- ___________ effects of ultrasound increase tissue
permeability and acoustic pressure drives
molecules into the tissue - Effectiveness of phonophoresis is debatable
- Early studies demonstrated effective penetration
- (Griffin, 1982, Kleinkort, 1975)
- More recent studies show ineffectiveness
- (Oziomek et al, 1991, Benson et al., 1989)
68Ultrasound and Other Modalities
- US and Hot Packs _______________
- US and Cold Packs _______________
- Cooling the tissues does not facilitate an
increase in temperature (Remmington 1994, Draper,
1995) - Analgesic effects of ice can interfere with
perception of heating - Pulsed US may be beneficial during
Inflammatory-Response Phase of healing - US and E-Stim _______________
- Effective in treating myofascial trigger points
when used in combination with stretching
(Girardi, et al. 1984)
69Ultrasound Treatment Indications and
Contraindications
- Table 5-8, p. 127 --- Memorize!!!
- Guidelines for the safe use of ultrasound
equipment, p. 126-127