Title: Gas Risk Management
1Gas Risk Management
- Sierra Monitor and Rep Firm Welcome
- ABC Engineering
2Gas Risk Management
3Gas Risk Management
- Was this caused by someone not paying attention?
4Gas Risk Management
- Did some piece of equipment or instrumentation
fail?
5Gas Risk Management
- Did someone not follow procedure?
6Gas Risk Management
- Could a properly functioning safety system
have prevented the disaster?
7Gas Risk Management
- Explanation of hazardous gases
- Characteristics of common toxic gases
- Sensor Technology
- Portable and Fixed systems
- Placement of fixed sensors
- Elements of risk reduction
- Overview of available equipment
- Resources and reference
- Applications and usage
8Gas Risk Management
9Hazardous Gases
- Combustible Gases
- Explosion or fire hazard
- Must maintain concentration below lower explosive
limit (LEL) - Toxic Gases
- Hazardous to human health and safety
- Employee exposure must be limited
- Oxygen Displacing Gases
- Indirect human health hazard
- Deficiency of breathing Oxygen
10Combustible Gases
- Lower Explosive Limit (LEL)
- Also Lower Flammable Limit (LFL)
- What does it mean?
- Volume vs. LEL
- ASTM E681 Standard
- Benchmark test to determine LEL
- Tested in Air with 20.9 Oxygen
11Combustible Gases
100 LEL Methane 5 by volume
100
Too Rich for Combustion
Upper Explosive Limit U.E.L.
CONCENTRATION ( Gas in Air)
Will Support Combustion
Lower Explosive Limit 100 L.E.L.
Too Lean for Combustion
0
12Combustible Gases
Methane
Pentane
- The flammability of many gases lies in a very
limited range - The LEL differs depending upon the type of gas
100
100
CONCENTRATION ( Gas in Air)
CONCENTRATION ( Gas in Air)
15
UEL
7.8
UEL
5
100 LEL
1.5
100 LEL
0
0
13Combustible Gases
- Combustion Requires
- Fuel Source
- Oxygen or Air
- Ignition Source
14Combustible Gases
- Possible Ignition Sources
- Static Electricity Discharge
- Open Flames
- Hot Surfaces
- Mechanical Friction
- Electrical Arc or Spark
- Two Way Radio Transmitter
- Tools and Test Equipment
15Toxic Gases
- Hazard to Human Health and Life Safety
- PPM Parts Per Million
- 1 by volume 10,000 ppm
- 1 ppm .0001 by volume
- 1 millionth of the width of the U.S. is 12 feet
16Toxic Gases
- Permissible Exposure Limit (PEL)
- Time Weighted Average (TWA)
- Short Term Exposure Limit (STEL)
- Immediate Danger to Life and Health (IDLH)
- Relative Gas Density
- RGasD Air 1.0
- Lighter than air, Below 1.0
- Heavier than air, Above 1.0
17Carbon Monoxide Hazard
- Conc. of
- CO in Air Toxic Symptoms
- 100 ppm Fatigue and feeling of being tired
- 400 ppm Headache within 1-2 hrs., widespread in
2.5 - 3.5 hrs. - 500 ppm Dizziness, nausea, convulsions within 45
min. - 1,600 ppm Headache, dizziness, nausea within 20
min. Death in 2 hours. - 3,200 ppm Headache, nausea within 5-10 min.
Death within 30 min. - 6,400 ppm Headache, dizziness within 1-2 min.
Death within 10-15 min. - 12,800 ppm Death within 1-3 minutes.
18Carbon Monoxide Hazard
- OSHA General Industrial Safety Order for Carbon
Monoxide - Permissible Exposure Limit
- (Max. 8 hr. TWA) 50 ppm
- Short Term Excursion Limit (STEL) 200 ppm
for 15 min/8 hrs - IDLH 1200 ppm
- RGasD 0.97
19Chlorine Hazard
- Conc. of
- Cl2 in Air Toxic Symptoms
- 0.1 ppm Minimum concentration detectable by odor
- 3 ppm Difficulty breathing eye and throat
irritation - 10 ppm Causes serious throat irritation,
smarting of eyes - 30 ppm Coughing, more severe throat irritation,
general feeling of discomfort in the chest - 40 ppm Respiratory reflexes, coughing, burning
of eyes, nausea, vomiting. Possible death
within 30 minutes - 100 ppm Death within a few breaths
- Uses Water purification, sanitation of
industrial wastes, swimming pools, bleaching of
pulp and textiles, manufacture of various
chemical compounds
20Chlorine Hazard
- OSHA General Industrial Safety Order for Chlorine
- Permissible Exposure Limit
- (Max. 8 hr. TWA) 0.5 ppm
- Short Term Excursion Limit (STEL) 1 ppm for 15
min/8 hrs - IDLH 10 ppm
- RGasD 2.47
21Hydrogen Sulfide Hazard
- Conc. of
- H2S in Air Toxic Symptoms
- 1 ppm Odor detected, irritation of respiratory
tract - 10 ppm Allowable for 8 hours exposure (OSHA)
- 20 ppm Protective equipment is necessary
- 100 ppm Smell killed in 5 to 15 minutes. May
burn - eyes and throat coughing
- 500 ppm Respiratory disturbances in 2 to 15
minutes. Coughing, collapse unconsciousness - 1,000 ppm Immediate unconsciousness. Brain
damage may result unless rescued promptly.
Death in 3 to 5 minutes.
22Hydrogen Sulfide Hazard
- OSHA General Industrial Safety Order for Hydrogen
Sulfide - Permissible Exposure Limit
- (Max. 8 hr. TWA) 10 ppm
- Short Term Excursion Limit (STEL) 15 ppm for 10
min/8 hrs - IDLH 100 ppm
- RGasD 1.19
23Ammonia Hazard
- Conc. of
- NH3 in Air Toxic Symptoms
- 2 ppm First perceptible odor
- 40 ppm Slight eye and throat irritation
- 100 ppm Acute Irritation of eyes and nasal
passages - 400 ppm Severe irritation of throat, nose, upper
respiratory tract - 700 ppm Severe eye irritation
- 1700 ppm Serious coughing, bronchial spasms,
death within 30 min. - 5000 ppm Serious edema, strangulation, asphyxia,
death immediate - Uses Refrigerant gas, used in soil
fertilization, ammoniate fertilizers. Used in
metal treating and for extraction of metals from
ores. Used as a neutralizing agent of acids in
oil and in the manufacture of various chemical
compounds. Also used to purify municipal water
supplies.
24Ammonia Hazard
- OSHA General Industrial Safety Order for Ammonia
- Permissible Exposure Limit
- (Max. 8 hr. TWA) 25 ppm
- Short Term Excursion Limit (STEL) 35
ppm for 15 min/8 hrs - IDLH 300 ppm
- RGasD 0.60
25Oxygen Deficiency Hazard
- Oxygen
- Content Symptoms Developed
- 20.9 Normal Oxygen concentration in air
- 15 - 19 Decreased ability to work strenuously.
- May impair coordination
- 12 - 14 Respiration increases in exertion, pulse
up, impaired coordination, perception
judgment - 8 - 10 Mental failure, fainting,
unconsciousness, blueness of lips, nausea
vomiting - 6 - 8 8 minutes, 100 fatal 6 minutes, 50
fatal, - 4 - 5 minutes, recovery with treatment
- 4 - 6 Coma in 40 seconds, convulsions,
respiration ceases, death
26Oxygen Deficiency Hazard
- Industry Guidelines for Oxygen Deficiency
- Breathing gear required below 19.5 and above
23.5 Oxygen content in air - Confined Space permit procedures may need be
followed in some areas
27Gas Risk Management
28Sensor Technology
- Catalytic Bead
- Infrared
- Electrochemical
- Semiconductor
29Catalytic Bead
- No Temperature or Humidity Effect
- Silicone and Sulfide Resistant
- 0-100 L.E.L. Scale
- Responds to All Combustible Gases
- Wheatstone Bridge
30Catalytic Bead
Wheatstone Bridge
Compensator
DC Supply
Detector
Output
31Infrared
- Methane or Propane
- Carbon Dioxide
- Accurate Stable
- Large Measurement Range
- Low Maintenance
32Electrochemical
- Current Generating Electrolytic Reaction
- High sensitivity for PPM levels of Toxic Gas
- Specificity to Gas of Interest
- Percent Volume for Oxygen Measurement
Diffusion Point
Electrolyte
Electrodes
33Semiconductor (Solid State)
- Long Life Sensor
- Semiconductor Resistive Film
- PPM Range
- High Sensitivity
- Poor Selectivity
- Non-Linear Response
34Detection Techniques
- Combustible Catalytic bead, Semiconductor,
Infrared - Oxygen Electrochemical
- Toxic Gases Semiconductor, Electrochemical,
Infrared
35Gas Risk Management
- Explanation of hazardous gases
- Characteristics of common toxic gases
- Sensor Technology
- Portable and Fixed systems
- Placement of fixed sensors
- Elements of risk reduction
- Overview of available equipment
- Resources and reference
- Applications and usage
36Portables vs. Fixed
- Use Portables
- When area is not normally occupied
- When area has no power or infrastructure
- When temporary work crew must maintain their own
safety equipment - When fixed system is down for maintenance
- Use of Fixed Systems
- When area is regularly occupied
- When automatic systems must react to a hazardous
gas condition - When insurance or regulatory issues require it
- When risk assessment concludes that area must be
monitored continuously 24/7
37Portable Devices
- Battery Powered
- Can be moved from area to area
- Monitor is attached to the individual who is
performing the work - Prone to damage
- Should be calibrated before every use
38Permanent Fixed Installations
SCADA
39Calibration Validation
- Factory Mutual (FM) requires that all approved
sensors be calibrated periodically - Sensor must be exposed to live gas standard to
validate performance - Regular calibration compensates for environmental
changes - Records must be maintained to meet OSHA Due
Diligence requirements - Calibration gas must be certified as primary gas
standard
40Gas Risk Management
41Gas Sensor Placement
- Use engineering judgement
- Consider
- Probability of gas leak
- Quantity of gas that could leak
- Environmental conditions
- Dilution rates and convection currents
- Density of gas
- Interfering gases
42Gas Sensor Placement
- Place sensors close to possible gas source
- Place sensors in areas where gas might accumulate
- Place toxic gas and oxygen deficiency sensors in
the breathing zone - Consider accessibility and maintenance issues
43Gas Weight in Relation to Air
- Ammonia Lighter
- Butane Heavier
- Carbon Dioxide Heavier
- Carbon Monoxide Slightly Lighter
- Methane Lighter
- Chlorine Heavier
- Ethane Slightly Heavier
- Ethylene Slightly Lighter
- Heptane Heavier
- Hydrogen Lighter
44Gas Weight in Relation to Air
- Hydrogen Chloride Heavier
- Hydrogen Cyanide Lighter
- Hydrogen Sulfide Heavier
- Methyl Alcohol Heavier
- Nitric Oxide Slightly Heavier
- Nitrogen Dioxide Heavier
- Pentane Heavier
- Propane Heavier
- Sulfur Dioxide Heavier
- Toluene Heavier
45Gas Risk Management
46Responsible Risk Management
- Identify hazards...
- Assess risk of hazardous event...
- Comply with laws, insurance requirements...
- Consider liability, financial risks...
- Develop and implement a strategy of comprehensive
event response and prudent risk management
47Risk Reduction
48Proper Equipment Selection
- Portable systems
- Minimal risk of hazardous event
- Battery powered, must be carried on person
- Gas Alarm Monitors
- Minimal risk of hazardous event
- Simple alarm alert, relay output
- Analog Monitors
- Moderate risk in defined location
- Continuous display, warning and high alarms,
limited diagnostics
49Proper Equipment Selection
- Gas Alarm Monitors/Systems
- Analog Monitors (Single Point)
- Distributed Digital Systems (Multi-Point)
Multi-Point Systems
Gas Alarm Systems
Single Point Systems
50Proper Equipment Selection
- Risk Management Systems
- Constant risk of hazardous event, defined areas
or facility-wide - Distributed intelligence for local control and
remote monitoring - Comprehensive event response
- Configurable alarm logic
- Extensive calibration, diagnostic capabilities
- Documentation of due diligence
51Sentry - Basic Configuration
110 VAC or 220 VAC
12 - 28 VDC
Low Alarm
High Alarm
Trouble
RS232 Serial Output to Printer
52Resources Reference
- ANSI/NFPA 325 Guide to fire hazard properties of
flammable liquids, gases and volatile solids - ANSI/NFPA 820 Fire protection in wastewater
treatment and collection facilities - NIOSH Guide to chemical hazards
- OSHA Guide for confined space hazards
53Markets - Gas Detection
- Water/Wastewater Treatment Plants
- Chemical/Petrochemical Plants
- Landfills Solid Waste
- Alternate Fueled Vehicles
- Food Drug
- Parking Garages
- Gas/Oil Operations
- Pulp Paper
54Water/Wastewater Treatment
- Pumping Stations
- Combustible gases, H2S, O2
- Influent/Barscreen Rooms
- Combustible gas, O2
- Grit Chamber Wet Wells
- Combustibles, O2, H2S
- Digester
- Combustible gas, H2S
- Furnace Room
- Combustible gas, CO
- Disinfection/ Dechlorination
- Cl2, SO2, NH3
55Chemical/Petrochemical Plants
- Pipelines compressor stations
- Combustible gas, H2S, flame
- Laboratories
- Toxic gases, O2 deficiency
- Railroad/truck loading stations
- Combustibles, toxics, flame
- Storage tanks
- Combustibles, flame
56Gas/Oil Operations
- Well site perimeters
- Combustible gas, H2S
- Sweetening plants, sour gas wells H2S
- Pipelines compressor stations
- Combustibles, toxics, flame
- Drilling operations
- Combustible gas, H2S, oxygen deficiency, flame
- Combustible gas leaks
57Remote Site Monitoring
- Modbus RTU serial communication link from Sentry
interfaces to a FieldServer WebServer - WebServer uses Sentry data to build dynamic
browser pages - Browser pages may be viewed over LAN, WAN or
Internet
58Sentry WebServer
- The Main screen ranges from the default layout of
a single Sentry system to custom graphics that
can include a photo or drawing of the building
with buttons to specific zones
Default
Custom
59Review Discussion
- Sierra Monitor Corporation
- www.sierramonitor.com
- 800-72-SIERRA
- 800-727-4377
- FieldServer Technologies
- www.fieldserver.com
- 888 509-1970