COMPACT HIGH POWER LASER DAZZLER™ (CHPLD)

1
COMPACT HIGH POWERLASER DAZZLER(CHPLD)
INITIALTRAINING PRESENTATION
2
TOPICS

• Introduction 3-7
• Warnings/Safety 8-9
• Specifications 10
• Nomenclature 11
• Battery Replacement 12
• On-Off Push Button 13
• Intermittent Button Switch 13
• Remote Switch Tail Module 14
• Make Safe When Not In Use 15
• Delrin Fixture 16
• Diffuser 17
• Cleaning 18-19
• Tips 20
• Questions 21

3
CHP LASER DAZZLER
A Portable, Non-Lethal, Eye-Safe, Multi-Purpose
Device Effective Both Day and Night
4
CHP LASER DAZZLER

• It is the most rugged/powerful/compact laser
  device available that is suitable for this
  purpose
• The CHPLD engages the target in a wall of green
  laser (532nm) light, which disorients and
  distracts the subject
• This is accomplished by overloading the optic
  nerve rendering the subject nearly sightless for
  a short period of time there is no doubt the
  individual will see the CHPLD, even in bright
  sunlight at 200 meters

5
CHP LASER DAZZLER

• Specifically designed for applications where
  gaining the instant attention of individuals in
  varying light conditions including clear, bright
  sunny days is critical
• IDEAL FOR CONVOY AND ENTRY CONTROL OPERATIONS
• Immediate recognition by approaching vehicles or
  pedestrians which avoids the use of lethal force
  due to confusion or unseen /unrecognized hand
  signals

6
Drivers approaching a convoy or checkpoint may
not see hand signals or realize they are entering
a restricted/danger zone
CHPLD at 100 yards bright daylight
They cannot fail to see the CHPLD even if
distracted by traffic, sunlight, pedestrians, or
other activities
7

• OTHER USES
• Mark your position and identify friendly units at
  long distances
• Distraction disruption of hostile groups
• Counter sniper
• Block line of sight when approaching target
• Counter surveillance

Mounted on Tripod
Front view showing 4 lasers
8
WARNINGS/SAFETY

• Laser Dazzlers are non-lethal devices, HOWEVER,
  with the potential for permanent eye damage if
  used improperly the CHPLD should always be
  TREATED LIKE A LOADED WEAPON
• DO NOT point this device at any person unless it
  is operationally required
• The user is solely responsible for the safe
  operation of the CHPLD and for adhering to the
  instructions and warnings provided
• DO NOT look at the CHPLD thru optical devices
  such as binoculars or telescopes
• This device has sufficient energy densities to
  cause irreversible eye damage and or permanent
  blindness if used on a subject at close distances
  or reflected onto a subjects eyes from a highly
  reflective surface

9
WARNINGS/SAFETY

• DO NOT use on subjects at distances closer than
  20 meters or reflect back on subjects at
  distances equivalent to 20 meters or closer
  without the holographic diffuser installed
• DO NOT use on subjects at distances closer than 3
  meters or reflect back on subjects at distances
  equivalent to 3 meters or closer with the with
  the holographic diffuser installed
• The CHPLD is powered by lithium sulfur dioxide
  primary batteries and are therefore NOT
  RECHARGEABLE
• DO NOT attempt to charge the battery pack. Any
  attempt to do so is dangerous

10
SPECIFICATIONS

• 500 Milliwatt, 532nm (green) flashing laser
• Overall length - 11 inches
• Maximum diameter - 2.5 inches
• Powered by lithium sulfur dioxide primary
  batteries
• BATTERIES ARE NOT RECHARGABLE
• Safe Ranges
• Minimum eye safe range 20 meters (Without
  holographic diffuser)
• Minimum eye safe range 3 meters (With
  holographic diffuser)
• Maximum effective range
• 200 meters bright sunlight
• 2 kilometers night
• Construction
• Anodized aluminum
• Weight 2.0 lbs.
• Weight as shown 2.6 lbs.
• All parts produced in the USA
• Operating Conditions
• All-weather, general purpose and water tight

11
NOMENCLATURE
Aiming Device
DELRIN FIXTURE
CHPLD
12
BATTERY REPLACEMENT

• Unscrew tail module
• Install battery positive end first
• Rotate battery for best fit when installing
• Check to confirm O-Ring (3) is still in place
• DO NOT over tighten switch module

13
ON-OFF PUSH BUTTON

• Push and release to turn on
• Push and release again to turn off

INTERMITTENT BUTTON SWITCH

• Operate laser by push and release of intermittent
  button switch

14
REMOTE SWITCH TAIL MODULE

• This module contains an electronic switch circuit
  powered by a capacitor which is charged by the
  battery pack when the laser is OFF
• INITIAL CHARGE REQUIRES 4 MINUTES

• The laser can be operated for 45 minutes
  continuously from the initial charge
• When the laser is turned off the capacitor is
  fully charged
• The cable connectors for this module are
  male/female pin type
• Mate each connector
• Secure by gently rotating the locking collar
  until it engages the mating part
• Rotate clockwise approximately 1/8 of a turn to
  lock in place

15
MAKE SAFE WHEN NOT IN USE

• Integral On-Off Push Button Switch Module
• Unscrew ¼ to ½ turn
• Press button to ensure laser does not fire
• If necessary unscrew additional ¼ turn increments
  until laser will not fire
• Remote Switch Tail Module
• Disconnect cable connectors
• DO NOT unscrew module since the capacitor charge
  may dissipate and the initial charge time (4
  minutes) would be required to operate the laser
• Press button switch to ensure laser does not fire
• Long Period of Non-use
• Remove battery pack
• Reinstall Tail Switch Module to prevent dirt and
  moisture from entering the device

16
DELRIN FIXTURE

• The laser is provided in the Delrin Fixture and
  sighted to the red dot reticule scope.
• An intermittent on/off button is built into the
  fixture and is armed by connecting the cable on
  the Tail Module to the mating connector on the
  Delrin Fixture
• Secure by gently rotating the locking collar
  until it engages the mating part
• Rotate clockwise approximately 1/8 of a turn to
  lock in place

17
DIFFUSER

• Adding the provided Holographic Diffuser reduces
  the minimum eye safety distance from 20 meters to
  only 3 meters
• Unscrew window module
• Remove white washer
• Place diffuser on window
• Reinstall white nylon washer
• Reinstall module on device

18
CLEANING

• Remove the laser from the Delrin Fixture
• Disconnect cable
• Remove the Tail Module
• Loosen the 6-32 set screws
• Slide the laser forward
• Make sure not to lose the O-Ring (3)
• It is not necessary to remove the set screws
• To reinstall just reverse the process

19
CLEANING

• Window
• With device front facing down unscrew window
  module
• Remove white nylon washer
• Turn module over and clean surface underneath
• The window O-Ring will drop out
• Clean window with appropriate cleaner such as
  Windex sprayed onto a cloth
• Reinstall in reverse order
• Make sure O-Ring (1) is in the groove
• Make sure O-Ring (2) is still on the laser body
• CHPLD
• Wipe with damp cloth and or a cleaner such as
  Windex sprayed onto the cloth
• DO NOT immerse in water or cleaning fluids
• NO OTHER FIELD DISASSEMBLY OF THE LASER OTHER
  THAN AS DESCRIBED ABOVE IS PERMITTED. DOING SO
  WILL DAMAGE THE DEVICE AND VOID THE WARRANTY

20
TIPS

• TIPS FOR EFFECTIVE USE
• Individuals or groups Aim at the center of the
  chest then raise the beam to eye level for a very
  short period of time repeat as necessary
• Vehicles Aim at the center of the windshield
  then move to the drivers side for a very short
  period of time repeat as necessary

21
QUESTIONS ?
Easily seen at 1 mile in bright sunlight