A Guide to Hardware, 4e - PowerPoint PPT Presentation

1 / 56
About This Presentation
Title:

A Guide to Hardware, 4e

Description:

Adapter (MAC, physical, or hardware) address: 48-bit (6-byte) id number ... Hardware, ... A Guide to Hardware, 4e. 14. Figure 10-10 A star bus network uses ... – PowerPoint PPT presentation

Number of Views:68
Avg rating:3.0/5.0
Slides: 57
Provided by: siski
Category:

less

Transcript and Presenter's Notes

Title: A Guide to Hardware, 4e


1
A Guide to Hardware, 4e
  • Chapter 10
  • PCs on a Network

2
Objectives
  • Learn about different types of physical network
    architectures
  • Learn how networking works with Windows
  • Learn how to install a network card and connect
    to a network
  • Learn how to set up and secure a wireless network
  • Learn about troubleshooting tools and tips for
    network connections

3
Introduction
  • Topics covered in this chapter
  • Technologies used to build networks
  • How Windows supports a network connection
  • How to connect a computer to a network
  • How switches and routers interface networks
  • How to setup and secure a wireless network
  • How to troubleshoot a network connection

4
Physical Network Architectures
  • Elements providing an overview of networks
  • The different sizes of networks
  • The different technologies used by networks
  • Some networking terms
  • Network types commonly encountered
  • Ethernet
  • Wireless networks
  • Telephone networks
  • Mostly outdated token ring and FDDI networks

5
Sizes of Networks
  • A network links two or more computers
  • PAN (personal area network)
  • Consists of personal devices at close range
  • LAN (local area network)
  • Covers a small local area such as a home, or
    office
  • MAN (metropolitan area network)
  • Covers a large campus or city
  • WAN (wide area network)
  • Covers a large geographical area e.g., the
    Internet

6
Networking Technologies
  • Factors driving network evolution
  • The type of data the network is intended to
    support
  • The data capacity on the network
  • How a network is to fit among other networks
  • Bandwidth (data throughput or line speed)
  • Analog systems measured in cycles/sec (hertz or
    Hz)
  • Digital systems measured in bps, Kbps, or Mbps
  • As networks grow, the need for bandwidth grows

7
Additional Terms Used in Networking
  • Node (host) one device on a network e.g.,
    server
  • Network adapter interfaces a PC with a network
  • Network interface card (NIC) fits in a PCI slot
  • Adapter (MAC, physical, or hardware) address
  • 48-bit (6-byte) id number hard-coded on card
  • Example 00-0C-6E-4E-AB-A5
  • Network protocols rules of communication
  • Packets (datagrams or frames)
  • Basic unit of data transmitted on a network

8
Figure 10-1 Ethernet network card showing its MAC
address
9
Introducing Ethernet
  • Ethernet types (categorized by speed)
  • 10-Mbps Ethernet
  • 100-Mbps or Fast Ethernet
  • 1000-Mbps or Gigabit Ethernet
  • 10-Gigabit Ethernet
  • Types of cabling used
  • Two kinds of twisted-pair
  • Unshielded twisted pair (UTP) four pairs of
    twisted wire
  • Shielded twisted pair (STP) protected from EMI
  • Coaxial cable single copper wire with braided
    shield
  • Fiber-optic glass strands inside protective
    tubing

10
Table 10-2 Variations of Ethernet and Ethernet
cabling
11
Figure 10-4 Fiber-optic cables contain a glass
core for transmitting light
12
Introducing Ethernet (continued)
  • Topology arrangement of nodes in a network
  • Bus topology connects all nodes with a line (no
    hub)
  • Star topology
  • Connects nodes to central hub (or switch)
  • The hub broadcasts a data packet to every device
  • Switch uses a table to route packet to receiving
    device
  • Scale networks by adding switches
  • Star bus topology
  • Multiple switches form a bus network
  • Nodes connected to each switch form a star

13
Figure 10-6 Nodes on an Ethernet network can be
connected to one another in a star or bus
formation
14
Figure 10-10 A star bus network uses more than
one switch
15
Introducing Ethernet (continued)
  • Attenuation the weakening of a transmitted
    signal
  • Repeater device used to amplify a signal in a
    LAN
  • Amplifier repeater simply amplifies incoming
    signal
  • Signal-regenerating repeater
  • Reads and copies the signal (without noise)
  • Transmits an exact duplicate of the original
  • Ethernet uses a signal-regenerating repeater
  • A switch or hub can act as the repeater

16
Quick Quiz 1
  • 1. A(n) ____________________, such as the
    Internet, covers a large geographical area and is
    made up of many smaller networks.
  • Answer WAN (wide area network)
  • 2. ____________________ cables transmit signals
    as pulses of light over glass strands inside
    protected tubing.
  • Answer Fiber-optic
  • 3. A(n) ____________________ is a device that
    amplifies signals on a network.
  • Answer repeater
  • 4. All wireless phone systems, including
    cellular, use ____________________ transmission,
    which means both persons in a conversation can
    talk or transmit at the same time.
  • Answer full-duplex

17
Figure 10-14 A repeater on a network restores the
clarity of the signal, which degrades over a
distance because of attenuation
18
Wireless Networks
  • Use radio waves or infrared light to connect PCs
  • Popular in places where cables are difficult to
    install
  • 802.11wireless (Wi-Fi or Wireless Fidelity)
  • Types 802.11g (most popular), 802.11b, 802.11a
  • Two new standards 802.11k and 802.11r
  • Ad hoc mode directly links two wireless devices
  • Access point (AP) connects wireless device to
    LAN
  • WiMAX (802.16 Wireless/802.16d and 802.16e)
  • Used in public hot spots and as a last mile
    solution
  • Bluetooth short range standard e.g., optical
    mouse

19
Figure 10-16 Nodes on a wireless LAN connect to a
cabled network by way of an access point
20
Telephone Networks
  • Plain old telephone service (POTS)
  • Switching creates closed circuits between phones
  • VoIP (Voice over Internet Protocol)
  • Uses packets of data to communicate
  • Cellular WAN
  • Made up cells created by base stations
  • Cellular WAN standards
  • GSM (Global System for Mobile Communications)
  • CDMA (Code Division Multiple Access)
  • TDMA (Time Division Multiple Access)

21
Figure 10-20 A cellular WAN is made up of many
cells that provide coverage over a wide area
22
Telephone Networks (continued)
  • General Packet Radio Service (GPRS)
  • New communication protocol using data packets
  • Two types of transmission
  • Full-duplex allows both users to talk and
    transmit
  • Half-duplex allows only one user on a channel
  • Satellite phone communicates with satellites
  • Cordless phone communicates with phone base
  • Radio phone uses VHF radio waves

23
Token Ring and FDDI
  • Token Ring is physically a star, logically a ring
  • Components of a token ring
  • Controlled Access Unit (CAU)
  • Multistation Access Unit (MSAU or MAU)
  • Token Ring LAN card connecting node to MSAU
  • UTP or STP cables with two twisted pairs
  • RJ-45 or Universal Data Connector (UDC)
  • Fiber Distributed Data Interface (FDDI)
  • Uses a token that travels in a ring like a Token
    Ring
  • Data frames travel on the ring without the token

24
Figure 10-21 Full-duplex and half-duplex
transmissions
25
Windows on a Network
  • Major software components on a network
  • An operating system installed on each PC
  • Network operating system (NOS) for larger
    networks
  • Peer-to-peer network (workgroup)
  • Each PC has the same authority on the network
  • Client/server model (domain)
  • Access to network resources controlled by an NOS
  • Server is called a domain controller
  • A few network operating systems
  • Windows 2003 Server, Novell NetWare, Linux

26
Four Suites of Protocols
  • TCP/IP (Transmission Control Protocol/Internet
    Protocol)
  • Primary protocol used on the Internet
  • IPX/SPX (Internetwork Packet Exchange/Sequenced
    Packet Exchange)
  • Designed for use with Novell NetWare
  • NetBEUI (NetBIOS Extended User Interface)
  • Supports NetBIOS (Network Basic Input/Output
    System)
  • AppleTalk
  • Proprietary networking protocol suite for Macs

27
Figure 10-25 An operating system can use more
than one method to address a computer on the
network, but at the network level, a MAC address
is always used to address a device on the network
28
Four Suites of Protocols (continued)
  • Using a protocol on the network
  • Install a NIC card in the computer
  • Connect network cable to network device e.g., a
    switch
  • NIC card binds to higher level protocol e.g.,
    TCP/IP
  • How to identify which protocols are used in
    Windows
  • Look at the properties of a network connection
  • More than one OS protocol can be used on a
    network
  • New protocols may be installed
  • Network printers can be accessed in various ways

29
Figure 10-26 Three Windows XP network protocols
are installed and two protocols are bound to this
network card
30
Addressing on a Network
  • Four methods used to identify devices and
    programs
  • Using a MAC address
  • Using an IP address
  • Using character-based names (host, domain,
    NetBIOS)
  • Using a Port address
  • IP addresses
  • Used in TCP/IP to identify any device on the
    network
  • 4 bytes (octets) separated by dots e.g.,
    190.180.40.120
  • System allows for up to 4.3 billion IP addresses
  • First part identifies network, last part
    identifies host

31
Figure 10-27 Computers on the same LAN use MAC
addresses to communicate, but computers on
different LANs use IP addresses to communicate
over the Internet
32
Installing a NIC and Connecting to a Network
  • Components needed to connect a PC to a network
  • NIC and network port or wireless NIC card in the
    PC
  • Patch cable
  • Device for the PC to connect to, such as a router
  • NIC card selection criteria
  • NIC should match type of bus on motherboard
  • NIC should match speed and type of network
  • Wireless NIC should match network technology

33
Installing a NIC Using Windows 2000/XP
  • Overview of installation steps
  • Determine whether driver or NIC is installed
    first
  • If NIC precedes driver, install NIC and turn on
    PC
  • Follow instructions in Found New Hardware Wizard
  • Verify driver installation using the Device
    Manager
  • Update the driver if necessary
  • Connect patch cable to NIC port and network
    switch
  • Configuring Windows 2000/XP to use a network
  • Name computer in System Properties dialog box

34
Figure 10-32 Windows XP uses the Computer Name
Changes dialog box to assign a host name to a
computer on a network
35
Installing a NIC Using Windows 2000/XP (continued)
  • Questions to ask before configuring TCP/IP
  • Will the PC use dynamic or static IP addressing?
  • What are the IP address, subnet mask, default
    gateway?
  • A question to ask if static IP addressing is used
  • Do you use DNS?
  • If so, what are the IP addresses of your DNS
    servers?
  • Is a proxy server used to connect to other
    networks?
  • If so, what is the IP address of the proxy
    server?
  • Gateway device that connects two networks

36
Quick Quiz 2
  • 1. A(n) ____________________ computer provides a
    user ID and password to a server that validates
    the data against the security database.
  • Answer client
  • 2. A(n) ____________________ name is a name of a
    network.
  • Answer domain
  • 3. A(n) ____________________ is a computer or
    other device that allows a computer on one
    network to communicate with a computer on another
    network.
  • Answer gateway

37
Installing a NIC Using Windows 2000/XP (continued)
  • Internet Protocol (TCP/IP) Properties dialog box
  • Used to configure TCP/IP under Windows XP
  • Dialog opened from Properties of Local Area
    Connection
  • NWLink or NetBEUI protocol
  • Used for network communication (excluding the
    Internet)
  • Can be used in combination with TCP/IP
  • Installed from Properties of Local Area
    Connection

38
Figure 10-34 To configure TCP/IP under Windows
XP, use the Internet Protocol (TCP/IP) Properties
dialog box
39
Installing a NIC Using Windows 9x/Me
  • Overview of installation steps
  • Physically install the NIC and turn on the PC
  • Follow instructions of the Wizard
  • Verify the installation using Device Manager
  • Assigning a computer name
  • Access Identification tab in Network dialog box
  • Enter names of computer and workgroup
  • Verify assignment in Network Neighborhood window
  • Installing and configuring TCP/IP using Windows
    98
  • Use functions in the Network window

40
Figure 10-40 To configure TCP/IP in Windows 98,
select the binding and click Properties to view
the TCP/IP Properties dialog box
41
Installing a Wireless Adapter in a Notebook
  • Wireless adapter uses a USB port or PC Card slot
  • Installation package includes a CD and
    accessories
  • Overview of steps for installing a Linksys
    adapter
  • Install the software from the setup CD
  • Plug the wireless adapter into a USB port
  • Launch Found New Hardware and follow instructions
  • Managing the issue of an unsigned driver
  • Find approved driver or continue installation
  • Deciding which installation utility to use
  • Choose manufacturers utility over Windows XPs

42
Figure 10-45 Plug the wireless USB adapter into
the USB port
43
Installing a Wireless Adapter in a Notebook
(continued)
  • Information displayed about a current connection
  • MAC address of access point device used by
    adapter
  • The current channel the connection is using
  • Transfer rate, throughput, link quality, signal
    strength
  • Configuration changes you can make
  • Mode or network type
  • The SSID (service set identifier)
  • Encryption settings
  • Tx rate
  • TCP/IP configuration

44
Figure 10-49 Opening screen to configure a
Linksys wireless adapter
45
Installing a Wireless Adapter in a Notebook
(continued)
  • Connecting to a public hot spot using Windows XP
  • Open Wireless Network Connection dialog box
  • Select unsecured network from list and click
    Connect
  • Open a browser to test the connection
  • View link in Wireless Network Connection Status
    box
  • Two ways to troubleshoot a connection
  • Add network SSID in Wireless network properties
  • Provide MAC address to network administrator

46
Figure 10-57 Enter the SSID of a hot spot to
which you want to connect
47
How to Set Up Your Own Wireless Network
  • Two principal steps
  • Buy a wireless access point
  • Configure AP and wireless PC for communication
  • Providing security is critical for a successful
    network

48
Security on a Wireless LAN
  • Methods for securing a wireless connection
  • Disable SSID broadcasting
  • Filter MAC addresses
  • Data encryption e.g., WPA (WiFi Protected
    Access)
  • Change firmware default settings
  • Update firmware
  • Use a firewall
  • Virtual private network (VPN)

49
Figure 10-60 With tunneling, packets can travel
over a wireless LAN and the Internet in a virtual
private network (VPN), but WEP or WPA applies
only to the wireless connection
50
Choosing a Wireless Access Point
  • Selection criteria
  • The ability to use multiple security measures
  • Supports for the 802.11 b/g wireless standards
  • Good hardware reviews from other users
  • An access point can be a standalone device
  • An access point can also serve multiple purposes

51
Quick Quiz 3
  • 1. ____________________for Microsoft Networks is
    the Windows component that allows you to use
    resources on the network made available by other
    computers.
  • Answer Client
  • 2. A network drive ____________________ is one of
    the most powerful and versatile methods of
    communicating over a network.
  • Answer map
  • 3. A VPN (virtual private network) uses a
    technique called ____________________, in which a
    packet of data is encrypted.
  • Answer tunneling
  • 4. A ferrite ____________________ installed close
    to the device end of the cable protects against
    electrical interference.
  • Answer clamp

52
Configure and Test Your Wireless Network
  • Installing the hardware
  • Position device and plug it in
  • Connect the device using a network or USB cable
  • Access point configuration is saved on firmware
  • Configuring the access point
  • Change default password to the administrative
    utility
  • Select basic wireless settings, such as the
    channel
  • Set up data encryption
  • Choose whether to filter MAC addresses
  • Save the settings and test the connection

53
Figure 10-65 This wireless access point supports
several encryption methods
54
Troubleshooting a Network Connection
  • Some symptoms indicating a faulty NIC
  • You cannot make a connection to the network.
  • My Network Places does not show any other PCs
  • An error message displays during driver
    installation
  • Displaying TCP/IP connection information
  • Use Ipconfig under Windows 2000/XP
  • Use Winipcfg under Windows 9x/Me
  • Ping (Packet Internet Groper) diagnostic tool
  • Sends a signal to a remote computer
  • If remote PC is online and senses signal, it
    responds

55
Summary
  • Network system interconnecting two or more PCs
  • Basic network types PANs, LANs, MANs, and WANs
  • Bandwidth amount of data transmitted per unit
    time
  • Ethernet topologies bus, star, star bus
  • Wireless standards 802.11g/b/a/k/r, WiMAX,
    Bluetooth

56
Summary (continued)
  • Telephone technologies POTS, VoIP, Cellular WAN,
    satellite phone, cordless phone, and radio phone
  • OS level protocols TCP/IP, IPX/SPX, Net BEUI,
    AppleTalk
  • IP address 32-bit address identifying network
    node
  • Local Area Connection dialog box used to install
    and modify communication protocols
Write a Comment
User Comments (0)
About PowerShow.com