Title: Aucun titre de diapositive
1Evolution of Si-SiO2 interface trap density under
electrical stress in MOSFETs with ultrathin oxides
F. Rahmoune and D. Bauza Institut de
Microélectronique, Electromagnétisme et
Photonique (IMEP), UMR CNRS 5130, INPG, ENSERG,
23 rue des Martyrs, BP 257, 38016 Grenoble Cedex
1, France.
2 OUTLINE
1. Introduction 2. Extraction of Dit 2.1 Ghetti
et al model 2.2 Bauzas method 3. Results 3.1
Evolution of Dit with electrical stress 3.2
Discussion 4. Conclusion
3 1. Introduction
Dit extraction (ultra thin oxide) - Infeasible
up to recently due to QM effects, - Crucial for
evaluating the technological process, as
before, and for studying oxide degradation (at
low voltages the tunneling current is trap
assisted)
Bauzas method (EDL 2002) Small gate
pulse Decisive features allowing Dit
extraction 1. Tunneling current is strongly
reduced. 2. QM effects in the accumulation and
inversion layers can be overlooked. 3. Carrier
emission does not contribute to the CP
current.
Ghetti et al. Model (ED 2000) SILC
approach 1. Relies on the tunneling current with
Dit 2. Better understanding of SILC in MOS
devices with ultra thin oxides. 3. But numerous
parameters (Dit(E), ?, Dit(xox), mox, Eb )
and several possible mechanisms.
4 2. Extraction of Dit 2.1 Ghetti et al Model
(1/2) (IEEE TED Vol.
47 N12, 2000)
At high enough doping levels (? 8 1018 cm-3) and
at Vg lt 0, the main mechanism responsible for
the low voltage tunneling current is the
tunneling of gate electrons into the anode
interface states (TEDit). TEDit is given by the
numerical model
The possible components of low negative voltage
tunneling current.
5 2. Extraction of Dit 2.1 Ghetti et al
Model (2/2) (IEEE TED Vol. 47 N12, 2000)
JTEDit is very sensitive to 1. The
interface state distribution 2. The electrical
stress
Therefore, this technique can be exploited to
estimate Dit(E) in ultra thin oxides, as long as
Ig is detectable in the voltage range -Vfblt Vg
lt0.
6 2. Extraction of Dit -Principle of Charge
pumping
CP set up
Elliot curves
7 2. Extraction of Dit 2.2 Bauzas method
(1/3) (IEEE EDL Vol. 23
N11, 2002)
This method is based on small gate pulses. ? If
emission does not contribute to the CP current
and ? if all the traps, from fast to slow traps,
between the Fermi level position Ehand El at the
interface, are filled
Eq. 1
Procedure 1. Extract Elliot curves for a given
Vsw at different frequencies. 2.
Repeat procedure 1 for different values of
Vsw. 3. In the region of reliable extraction,
Dit (Eq. 1) should be independent of frequency
and gate pulse amplitude.
8 2. Extraction of Dit 2.2 Bauzas method
(2/3) (IEEE EDL Vol. 23 N11,
2002)
To obtain Elliot curves, the tunneling current
must be suppressed 1. Measure Icp (Vl)
2. Suppress the tunneling current by
measuring the same Elliot curves using
the lowest possible frequency (P.
Masson s method ) (EDL Vol.20 N2,1999)
Icp(Vl)
Elliot curve
9 2. Extraction of Dit 2.2 Bauzas method
(3/3) (IEEE EDL Vol. 23 N11,
2002)
In the region of reliable extraction, Dit (Eq.
1) should be independent of frequency
and pulse amplitude.
Dit 2 1010 eV-1cm-2
10 3. Results 3.1 Evolution of Dit with
electrical stress (1/4 )
In the SILC approach The relative variation of
the gate current density with stress, ?J/J0,
are equal to the relative variations of the
interface trap density ?J/J0 ?Dit/Dit0
11 3. Results 3.1 Evolution of Dit with
electrical stress (2/4 )
Dit0 of SILC value measured by CP
12 3. Results 3.1 Evolution of Dit with
electrical stress (3/4 )
Case of other oxide thickness
?Dit/Dit0 SILC gtgt ?Dit/Dit0 CP
13 3. Results 3.1 Evolution of Dit with
electrical stress (4/4 )
Sensing Vg lt 0
Sensing Vg gt 0
At Vg gt 0, electrons tunnel from the interface
states towards the gate. The lower part of the Si
bandgap is probed.
?Dit/Dit0 SILC gt ?Dit/Dit0 CP
14 3. Results 3.2 Discussion
1. Results, i.e. SILC with regard to CP, are
similar whatever dox is. 2. SILC 2.1 The Dit
variations depend on the sensing bias used. 2.2
This corresponds to Dit (or ?) increasing faster
with stress from the
valence band edge towards the conduction
band edge (EC). A---------gt
EC C---------gt Ei C -------gt EV 2.3
?Dit always greater for SILC than for CP. 2.4 ?
variations can not explain the results also. 3.
CP - Averages Dit in the energy region scanned
(?0.35 to ?0.42 eVfrom Ei depending on the
devices). ? SILC and CP results can
not be reconciled.
15 4. Conclusion
1. The evolution of Dit under electrical stress
has been studied using a recent CP based
technique. 2. The results have been compared
with those obtained from SILC measurements. 3.
The variations of Dit under electrical stress are
found larger in the SILC approach than when
measured by CP, regardless of the oxide
thickness. 4. Ghettis model (Tunneling from the
gate towards Si-SiO2 interface states) holds for
high doping levels. 5. Our results are similar
regardless of the doping level and always give
much lower ?Dit values than SILC. ? It
seems that there is not a simple explanation for
SILC results, i.e. large
variations and mechanism. ? Interest of
CP for Dit extraction and SILC study in
state-of-the art MOS devices.